c07bbd4154
Prettify some EEPROM code
7 years ago
d6aa127c76
Remove I2CPEM workspace offset
7 years ago
79772219ae
Fix Fan Multiplexer init
7 years ago
ca7d36d9ed
RAMPS pins for ANET_KEYPAD_LCD
7 years ago
e0a6ee8da5
[2.0] Fix up G33, LPC1768 + SDCARD_SORT_ALPHA ( #8250 )
* Update Conditionals_post.h
* Add a cast to round() to convert to a unsigned int
Add's a cast to round() so that it will compile properly. round() returns a float which must be cast to a integer for the following % operation. Use a unsigned int as a negative index to an array is wrong. Should never be more than 255 points allowing us to use a 8 bit cast.
* Update G33.cpp
7 years ago
dac1f6fe74
Tweaks to cubic_b_spline code style
7 years ago
601ccded89
Fix case-insensitive config issue
7 years ago
f8393a0908
Operate in Native Machine Space
7 years ago
93ba72ea83
Add SERIAL_PORT -1, set on SBASE, STM32F103RET6
7 years ago
7e43dd1d23
Fix probes configuration url
Based on #8241 by @machaj
7 years ago
ca0e4b4e96
Some cleanup around 'lcd_bootscreen()' and 'lcd_kill_screen()'
Move 'lcd_bootscreen()' from `lcd_init()` to 'setup()' where it is cexecute exactly once. Saves 'bool show_bootscreen'.
Move the call of 'lcd_custom_bootscreen()' to the begin of 'lcd_bootscreen()'.
Move the delays into the related functions.
Move the picture loop around 'lcd_kill_screen()' into the function.
7 years ago
70be4d206e
[2.0.x] UltiMachine Archim2 ( #8190 )
* UltiMachine Archim2 support
* SPI gets included by the library
* Invert TMC2130 diag pin state
* Clean up Archim2 pins
* Update Archim2 config
* FAN2 -> FAN1
* Cleanup
* Add brief Archim installation instructions
* Bring pins into compliance
* Update 1.0 SD Detect pin for 1.1
* Update Configuration.h
* Update pins_ARCHIM2.h
7 years ago
31f112cf58
Cleanup trailing whitespace
7 years ago
2f9e42feb9
M303 thermal runaway protection
7 years ago
e5ae545647
Remove ADCKey steps acceleration
7 years ago
6827e243a0
[2.0.x] G33 magic numbers ( #8171 )
* [2.0.x] G33 magic numbers
* oops
* Comments
* oops
* warning
* better comment section
* remarks
* extra grids
7 years ago
c72a0610b4
Fix watchdog in WATCHDOG_RESET_MANUAL mode AVR
7 years ago
13d839795c
LPC1768: updates to use the new pin_t typedef
7 years ago
eb13b8d985
Add MKS Gen L board
7 years ago
063e957fc4
Update pins_MKS_SBASE.h ( #8188 )
* Update pins_MKS_SBASE.h
Deleted E_MUX2, not used.
Changed #define LCD_PINS_D4 P0_14 // EXP1.5 to #define LCD_PINS_D4 P0_15 // EXP1.5, wrong in MKS's pinout schematic.
Swapped TEMP_BED_PIN and TEMP_0_PIN port's, request from user, more logical...
* Update pins_MKS_SBASE.h
Moved MUX signals to J8 and re added MUX2, cleaner wiring..
7 years ago
f7133e53fd
Fix case light off
Addressing #8205
7 years ago
0108d5181f
Allow asterisks in G-Code commands
Addressing #6655
7 years ago
34745b2183
Organize boards.h by architecture
7 years ago
9cc1d8e312
[2.0.x] Support for SilverGate Board
7 years ago
03e5369411
Faster menu navigation for Anet A8
Addressing #8166
7 years ago
571ced712d
Add SDCARD_SORT_ALPHA options for LPC1768
7 years ago
778e4e4c23
Update InterruptVectors_Due.cpp
const pfnISR_Handler *isrtab = get_relocated_table_addr();
What compiler do you use? Arduino 1.8.5 can't compile this "const".
7 years ago
a516856df9
Only show custom bootscreen once
7 years ago
727a403ba1
[2.0.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour ( #8176 )
* [2.0.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour
NO_MOTION_BEFORE_HOMING should prevent XYZ movements only when homing is not done.
E axes should be allowed
* Update G0_G1.cpp
* Update G0_G1.cpp
7 years ago
577659cacf
Basic support for Azteeg_X5_GT ( #8139 )
* Basic support for Azteeg_X5_GT
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
* Add fan pins for AZTEEG X5 GT
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
* Fix endstop pins
* Add servo0 pin
7 years ago
04c0d9f3c3
Implement kinematic software endstops
7 years ago
9f89b5d876
Fix for MAX_VFAT_ENTRIES sanity check
7 years ago
2cdde08339
Apply items specified in code review
Followup to #8122
7 years ago
34be5d33c0
The plural of 'axis' is 'axes'
7 years ago
b7a66742dd
tested
add sort alpha section to other LPC1768 boards
7 years ago
bbc2e66634
Fix AZSMZ MINI pins for new LPC1768 pinmapping
7 years ago
31e96935f7
Fix EXTRA_FAN_SPEED
Addressing #8158
7 years ago
ce1c9c0808
Tweak QUICK_HOME description
7 years ago
12458cefc4
Remove 5s timer hack. Encoder pos is saved on print start!
7 years ago
9a4cf11835
Remove return_to_status_ms hack, just use defer...
7 years ago
8949c8c0a5
Move SD_REPRINT_LAST_SELECTED_FILE to ultralcd.cpp
7 years ago
723f2a77f6
Implement support for Dual X and Y endstops
7 years ago
e04425281d
Add Dual Steppers / Endstops to configs
7 years ago
edff2c917b
Cleanup for DIGIPOTS settings
7 years ago
3e8754a38a
Add/correct time units on planner vars / M205 B
7 years ago
b2a48f1a04
Provide a SERVO0_PIN for non-standard LCD
7 years ago
b232f39341
AVR: Hidden option to use 8s watchdog
7 years ago
eae0aea1e0
Fix M303 thermal protection
7 years ago
a1a4fc277e
(2.0.x) serious bug G33 ( #8136 )
* (2.0.x) serious bug G33
* Revert config changes
This reverts commit 74b5a98223b7b7fb970d05b8541f4a079c3cfe56.
7 years ago
325233b454
Fix automatic stepper assignment for X/Y/Z dual stepper drivers ( #8130 )
7 years ago
Scott Lahteine
Colten Edwards
AnHardt
teemuatlut
Luc Van Daele
Thomas Moore
Morten
Scott Lahteine
android444
rafaljot
GMagician
Alexey Shvetsov
Bob-the-Kuhn
Jeffrey Li
Thomas Moore