a215725df6
Fix stepper pulse timing
Always honor minimum period on stepper pulse generation, and fix timing calculations
Signed-off-by: etagle <ejtagle@hotmail.com>
6 years ago
0d79128c8d
Localize stepper-specific defines
6 years ago
4dbec774b5
HAL_*_TIMER_RATE => *_TIMER_RATE
6 years ago
6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
6 years ago
39a7e7720d
Adaptive multiaxis step smoothing
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
6 years ago
3701869e6c
Add HAL_timer_start for AVR, use stepper timer to time pulses
6 years ago
ad8d3150aa
Cleanup for dual endstops homing
6 years ago
d3c02410a8
[2.0.x] Small assorted collection of fixes and improvements ( #10911 )
* Misc fixes and improvements
- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).
* Set position immediately when possible
6 years ago
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE ( #10885 )
6 years ago
0ca9db7051
Correct HOTENDS for SWITCHING_EXTRUDER
6 years ago
7b9f0302d4
Fix Bresenham rounding errors, add link to article ( #10871 )
6 years ago
2566342979
Adjust some commentary
6 years ago
6775a16c97
Fix switching extruder stepping with LA
6 years ago
aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
6 years ago
01d37e00af
Fix up stepper ISR with linear advance timing ( #10853 )
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
6 years ago
7261f48872
Fix reset of endstops and move state
6 years ago
50fa8e01c1
Minor optimization of axis_did_move bits
6 years ago
f28e366b77
Followup for core endstops
6 years ago
9644d56b42
Patches for core motion tests
6 years ago
3e3789da85
Regression: Endstops Core compatibility ( #10823 )
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
6 years ago
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
6 years ago
435ecb6b67
Followup to stepper/planner refactor
6 years ago
569df3fc0c
Fix interrupt-based endstop detection
- Also implemented real endstop reading on interrupt.
6 years ago
a11eb50a3e
Refactor and optimize Stepper/Planner
Better encapsulation and considerably reduce stepper jitter
6 years ago
7dc03ce721
Simplified fix for babystep pulse width
Alternative to the apparently superfluous double delay
6 years ago
65270d6a96
Fix LIN_ADVANCE + SWITCHING_EXTRUDER
Followup to #10656
6 years ago
9ad42d6617
add delay between pulse edges ( #10778 )
6 years ago
ba4c32eec5
Followup to _AXIS patch
6 years ago
d9154ebdf6
Followup to math patch
6 years ago
883b0c9880
Convert custom maths to inlines ( #10728 )
6 years ago
08e36e264e
Apply _AXIS macro
6 years ago
8f8c6a9bc4
Move get_axis_position_mm to Planner ( #10718 )
6 years ago
a1062eec5b
Better handling of DELAY_NS and DELAY_US ( #10716 )
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
6 years ago
3614e6ce0f
Fix Switching Extruder with Linear Advance
6 years ago
306f0f2135
Move Stepper::synchronize to Planner ( #10713 )
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
6 years ago
722aba77f3
Fix LIN_ADVANCE + SWITCHING_EXTRUDER stepper directions ( #10656 )
6 years ago
0436e16fb2
Apply shorthand Assembler macros
6 years ago
af1950a63e
Improve sync of stepper positions
6 years ago
0c23792344
Apply int32_t to stepper
6 years ago
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
6 years ago
36b97bde9f
clear_block_buffer, kill_current_block in quick_stop
6 years ago
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
6 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
6 years ago
7d8a46519f
Output ABC for delta stepper counts
6 years ago
1cb810ff1c
[2.0.x] Automatically reset stepper timeout ( #10179 )
* Automatically reset stepper timeout in manage_inactivity
Any code that adds moves to the planner can skip resetting the stepper timeout. We can let `idle` / `manage_inactivity` reset the timer whenever it detects any moves in the planner.
* blocks_queued => has_blocks_queued
6 years ago
48d7036874
Consolidate smart stepper driver initialization
6 years ago
eaefc1e410
Add CorePQ support for BABYSTEPPING ( #10155 )
6 years ago
51bf3c9503
Fix E direction for MK2_MULTIPLEXER with LIN_ADVANCE
6 years ago
e7570f3195
Improve TMC config organization, naming
6 years ago
751785fc97
Followup to recent patches
- `M666` is static, not inline
- Disambiguate some stepper macros
6 years ago
etagle
Scott Lahteine
Scott Lahteine
Bob Kuhn