03b01e2500
Folger Tech i3-2020 now defaults to 2 Max7219 units
6 years ago
db85ca93c4
Change Max7219_idle_task() to use a column instead of row if Y-Axis as 16 LED's
6 years ago
9660996cc3
Add Multi Unit Support for Max7219 to bugfix_2.0.0 ( #11285 )
* Add Multi Unit Support for Max7219 to bugfix_2.0.0
* Apply multi-MAX7219 to example configs
* Tweak some spacing, macros
6 years ago
39c8aed8ba
Add MANUAL_PROBE_START_Z to example configs
6 years ago
2106fa26b1
Add MANUAL_PROBE_START_Z for manual probing
6 years ago
17ed0f815c
Fix tool_change call in UBL G29
Fix #11279 , #11252
6 years ago
63a146d424
planner.synchronize at start of tool_change
See https://github.com/MarlinFirmware/Marlin/issues/10949#issuecomment-398540498
6 years ago
665ac1e4d0
Add POWER_LOSS_PIN support
6 years ago
2243f72523
Add POWER_LOSS_PIN to example configs
6 years ago
47d5fcbbcc
[2.0.x] Change MKS SBASE default serial port to avoid confusion ( #11301 )
6 years ago
64f007580b
Fix some header comments
6 years ago
aed1d17a2d
Initialize default units ( #11295 )
When `INCH_MODE_SUPPORT` is enabled no default unit is set. This fixes it.
6 years ago
8c40f0c6c7
Reduce TQ message code size
6 years ago
b04e0c0cbb
Malyan LCD feedrate, better temp handling.
6 years ago
065e9c3d66
Add card.longest_filename method
6 years ago
71df1f7f57
Don't display M421 information for UBL at startup
It takes too long to display the mesh data for large mesh's at startup. We should consider ways to speed this up.
Perhaps it makes sense to display an entire row of the mesh instead of just one mesh point?
6 years ago
8f686aa449
[2.0.x] Fix change filament crash ( #11269 )
Prevent crash, on filament change, when printer is not homed
6 years ago
f38c81cdde
LPC176x: Expand HW SPI class
7 years ago
3b5dec4b13
Add new LPC include folder
6 years ago
e486326910
Vellemann K8400 Y bed size is 180
Co-Authored-By: kaimimue <kaimimue@users.noreply.github.com>
6 years ago
e5ea9d200f
[2.0.x] fix kill printer ( #11260 )
This will fix kill message on dual printer with 0 alignment offset
6 years ago
8c57cadbe7
Include stdlib in fontutils ( #11251 )
When `REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER` is defined and Re-ARM build is attempted, `u8g_fontutf8.cpp` includes `fontutils.h` which uses `abs()`.
However, `abs()` is defined in `stdlib.h` which is not included in `fontutils.h`, so compile fails with an error.
Include `stdlib.h` in `fontutils.h` so that `abs()` is defined before `u8g_fontutf8.cpp` needs to use it, resolving the compile error.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
6 years ago
bf7d0ba859
Assert that XY probe offsets are integers
6 years ago
12854f1909
Add Z_CLEARANCE_MULTI_PROBE to example configs
Co-Authored-By: nightgryphon <ngryph@gmail.com>
6 years ago
25e2ca8896
Add Z_CLEARANCE_MULTI_PROBE
Co-Authored-By: nightgryphon <ngryph@gmail.com>
6 years ago
fd8a76493b
Unify M91x parameter I meaning, simplify reports ( #11249 )
6 years ago
566d05006d
report_state > event_handler
Make the endstop report method track endstop changes on its own.
6 years ago
6b521b6df2
Loosen thermistor table size limit
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
6 years ago
603e136e87
Resolve issue where user can't edit UBL's mesh
6 years ago
ed720194d2
[2.0.x][HD44780] Remove unused include
The <binary.h> header is not available in STM32 toolchain
and is not used anywhere in ultralcd_common_HD44780.h.
If it is used anywhere in HD44780 support for other platforms,
it must be included in the corresponding .cpp file directly
and put under appropriate conditional compilation directives
for the platform requiring it.
As I was unable to find such code, I consider the file unused
and hence remove the inclusion.
6 years ago
d05e832f29
Add STM32F1 support for SD-based EEPROM
6 years ago
63f4c9bdb9
Followup to float maths patch
6 years ago
2992112da0
Optimize delta kinematics
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
6 years ago
1367df2875
Replace double with float, optimize calculation
6 years ago
d960d448fa
Optimize calculations with LROUND
6 years ago
68e6650df7
Remove Quake Fast Inverse SQRT (it isn't faster)
6 years ago
e7e896e7d7
More tweaks to fastio_Due.h
6 years ago
55f4744e54
[LPC176x] Endstop Interrupts Feature ( #11202 )
Enable the endstop interrupts feature for LPC176x boards. Although Smoothieboard chose to use non-interrupt capable pins for their endstops, and this has been copied by clones, so they can't use it.
6 years ago
5abf5bc8a7
[LPC176x] Fix Interrupt forward declarations ( #11200 )
6 years ago
cbea385ed7
[2.0.x] Fix LCD_LANGUAGE options list formatting in config ( #11198 )
* Fix LCD_LANGUAGE options list formatting in config
* Remove 'cn' language option from list
6 years ago
5379c115c8
Fix Trigorilla include typo
6 years ago
9c058091e9
No M914 or SGT set for non-sensorless axes
6 years ago
c7ec6c68e7
Patch SCARA config to match 1.1.x
6 years ago
480a3d3d0c
Apply sensorless homing requirements only for specified axes
6 years ago
8c0ec81a19
Followup to #11187
6 years ago
48c1f32b3e
Add configurations for Tronxy X3A
6 years ago
568cfe7caa
Add thermistor 501 (100K Zonestar)
6 years ago
1a0f4dedad
Fix and improve POWER_LOSS_RECOVERY ( #11187 )
6 years ago
e0ab8acf19
Add "Marlin Dev Mode" option
6 years ago
4b2af6ab48
Minor patches to POWER_LOSS_RECOVERY
6 years ago
Roxy-3D
Scott Lahteine
Chris Pepper
Giuliano
xC0000005
teemuatlut
Jamie Bainbridge
Scott Lahteine
Alexander Amelkin
etagle