Scott Lahteine
19f189b4e5
Add UBL support for G2/G3 and G5 ( #10648 )
6 years ago
Scott Lahteine
4d4bf7897d
Junction Deviation jerk limiting option
6 years ago
Scott Lahteine
0436e16fb2
Apply shorthand Assembler macros
6 years ago
Scott Lahteine
d1b619be52
Standardize some hexadecimals
6 years ago
Scott Lahteine
55f1f8446b
Show correct current units in M503
6 years ago
Scott Lahteine
1f11b0f612
Fully init planner sync block
6 years ago
Scott Lahteine
bfe223e120
Adjust usage of stepper.synchronize
6 years ago
Scott Lahteine
af1950a63e
Improve sync of stepper positions
6 years ago
Scott Lahteine
0c23792344
Apply int32_t to stepper
6 years ago
Scott Lahteine
81b632c255
Additional temp-oriented improvements
6 years ago
nightdemonx
e911635fb1
Add thermocouple with AD8495 support
6 years ago
Scott Lahteine
d7b699ec34
Fewer includes of vector_3.h
6 years ago
Scott Lahteine
2c1205d8b1
Improve debug of homing move feedrate
6 years ago
Scott Lahteine
c8e4b7c8a6
Fix XY homing move away rate
6 years ago
MagoKimbra
1f92b9a4ed
Fix do_probe_move with fr_mm_s ( #10576 )
6 years ago
Scott Lahteine
4dfc011d86
Fix homing with probe feedrates
6 years ago
Scott Lahteine
59fda986ea
Allow Z_AFTER_PROBING to be 0
6 years ago
Scott Lahteine
1dab44213a
Fix the TMC26X initializer CS pin argument
From #10531
Co-Authored-By: chriscg9 <chriscg9@users.noreply.github.com>
6 years ago
Scott Lahteine
7546f87949
Allow a home bump of 0 when homing Z with probe
6 years ago
Scott Lahteine
683dc24e0f
When homing with Z probe bump at Z_PROBE_SPEED_SLOW
6 years ago
Scott Lahteine
5ac226aa93
Further cleanup of inline delays
6 years ago
Chris Pepper
2242b98248
[LPC176x] Emergency Parser Feature ( #10516 )
6 years ago
Scott Lahteine
9789c1c719
Fix current_temperature_chamber compile error
Fix #10505
6 years ago
Eduardo José Tagle
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
6 years ago
Scott Lahteine
f423e54f77
Strip trailing spaces
6 years ago
Scott Lahteine
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
6 years ago
Scott Lahteine
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
6 years ago
Scott Lahteine
5a064d0e94
Fix bug in planner.set_position_mm
6 years ago
Scott Lahteine
8f57e098de
Use end-of-line comments in planner.cpp
6 years ago
Scott Lahteine
36b97bde9f
clear_block_buffer, kill_current_block in quick_stop
6 years ago
Luc Van Daele
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
6 years ago
Luc Van Daele
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
6 years ago
Luc Van Daele
ac2e0afb62
Low Point for delta calibration ( #10363 )
6 years ago
Eduardo José Tagle
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
6 years ago
Sean
2d9b0a66fe
Add Filament Change accelerations
7 years ago
Scott Lahteine
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
6 years ago
etagle
a29adde5c0
Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
6 years ago
Lenbok
0e8242180d
Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
Marcio Teixeira
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
6 years ago
Scott Lahteine
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
6 years ago
Scott Lahteine
1c36606886
Fix MSG_HEATING_FAILED_LCD_BED macro evaluation
6 years ago
Scott Lahteine
fe91514395
MBL should add z_offset regardless of fade ( #10308 )
6 years ago
Marcio Teixeira
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
6 years ago
GMagician
21a47b50f4
Additional tool-change fixes ( #10304 )
Followup to #10257
6 years ago
Karl Andersson
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
6 years ago
Scott Lahteine
4c79dc1093
Fix a Serial+EEPROM compile error
Fixes #10278
6 years ago
Scott Lahteine
adcb87f0db
Z Endstop Servo => Z Probe Servo
6 years ago
Scott Lahteine
02f0f95d40
Handle disabled HYBRID_THRESHOLD in EEPROM ( #10275 )
6 years ago
Scott Lahteine
2672120a97
Do a small raise for all move-back
6 years ago
Scott Lahteine
5acccbacc1
Simplified leveling-based tool change
6 years ago