Marlin_FB4S

Commit Graph

Author	SHA1	Message	Date
Scott Lahteine	dd2949922b	Consolidate 3-point leveling point options	7 years ago
Scott Lahteine	c6ff39cc14	Spacing cleanup	7 years ago
Scott Lahteine	14c03cb6f4	[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) (#10069 ) Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.	7 years ago
Scott Lahteine	28f1276286	[2.0.x] Add Z_AFTER_PROBING option (#10058 ) Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.	7 years ago
Scott Lahteine	419d12ca1b	Add UNKNOWN_Z_NO_RAISE option With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.	7 years ago
Scott Lahteine	a2a672449a	Updated boot screen description	7 years ago
Scott Lahteine	4953fb1c88	Standardize encoder defaults	7 years ago
Scott Lahteine	5684beae90	Bring some configs up to speed	7 years ago
Scott Lahteine	2024775e07	Spanish (UTF8) Language (#9786 ) From #7314 by @MrAmericanMike	7 years ago
Scott Lahteine	b2cf253a13	Add RESTORE_LEVELING_AFTER_G28 option	7 years ago
Marcio Teixeira	716a22498f	Changed temp type from uint8_t to int16_t - Also deleted old implementation files which had been renamed.	7 years ago
Scott Lahteine	7d8c6b3f3c	Add 20x4 option for Sainsmart LCD (#9740 )	7 years ago
Marcio Teixeira	aada1e698f	Removed unused configuration options.	7 years ago
Studiodyne	d3ca82d8c2	Support for multiple filament runout sensors	7 years ago
Scott Lahteine	ca55f2927a	Pulldown pin mode support (#9701 ) Implemented for LPC1768.	7 years ago
Scott Lahteine	79272f98fc	Proposed changes to ST7920 lightweight status screen	7 years ago
Marcio Teixeira	24eb275b99	Added a light-weight status screen for the ST7920 - The status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen. - Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.	7 years ago
Scott Lahteine	08d685c97a	Followup to `21e60fd`	7 years ago
Roxy-3D	21e60fd3ed	Allow user to control Z-Height correction for off mesh movements (#9661 )	7 years ago
Marcio Teixeira	4880ac6533	Added a light-weight status screen for the ST7920 - The status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen. - Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.	7 years ago
Scott Lahteine	2ec65051fd	Fix serial comment sp.	7 years ago
Scott Lahteine	2014d38e10	NEOPIXEL_BRIGHTNESS parity	7 years ago
Scott Lahteine	b5e92f4f90	[2.0.x] Enable / disable PSU automatically (#9503 )	7 years ago
Scott Lahteine	16739264d3	Add UltiController v2.1 support Add compatibility with the original screen bord from Ultimaker 2 printer (UltiController v2.1 with the PG-2864ALBP I2C display)	7 years ago
Scott Lahteine	4925f60cff	Add MALYAN_LCD to configs	7 years ago
Scott Lahteine	7d6c009104	Add thermistor 15 tuned for JGAurora A5	7 years ago
Scott Lahteine	348b454401	Probe bounds based on bed size	7 years ago
Scott Lahteine	58ed9901d7	Consistent NEOPIXEL_TYPE options	7 years ago
Scott Lahteine	fa432508b0	Followup to Ender config	7 years ago
Scott Lahteine	048486390e	Bring some configs up to date	7 years ago
Thomas Moore	f7efac57b7	Multi-host support	7 years ago
GMagician	5295b4713d	[2.0.x] add semitec 104NT-4 (#9119 ) Table is very very similar to old 104-GT2 so I added only the name and recycled old ID	7 years ago
Scott Lahteine	0b4a46fa6c	Bring configs up to date with 1.1.x	7 years ago
Thomas Moore	f0a8a1a853	[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE (#8866 ) * Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE	7 years ago
Scott Lahteine	28fc8741d6	Reduce default jerk. XY by half. Z by 1/4	7 years ago
Even	ea1a8d1223	add original RADDS LCD + Controller adds setup for the original Radds Display+Controller+SD Card Reader PCB http://doku.radds.org/dokumentation/lcd-display/	7 years ago
Dan Delaney	b055d8c39c	[2.0.x] Adding support for using the MKS_12864OLED with the SSD1306 controller (#8814 ) * Adding support for using the MKS_12864OLED with the SSD1306 controller * Update comment for correct controller type	7 years ago
Scott Lahteine	15d05748df	Adding support for the Tronxy and Zonestar LCD	7 years ago
Scott Lahteine	69d49a2438	Shorter segments may be better	7 years ago
Scott Lahteine	ae663a4198	PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING	7 years ago
Richard Wackerbarth	c1184552ac	Change K1 to required option PID_K1	7 years ago
Scott Lahteine	aa7efb96bf	Bring configurations up to date	7 years ago
Scott Lahteine	0154e3480c	New feature: BED_SKEW_CORRECTION	7 years ago
Scott Lahteine	ef2531558c	Add an option to segment leveled moves	7 years ago
Scott Lahteine	5926c9c97b	Followup for MESH_EDIT_GFX_OVERLAY	7 years ago
Scott Lahteine	5ce7f23afa	Config option G26_MESH_VALIDATION for all meshes	7 years ago
Scott Lahteine	3f0a982b8c	Move Filament Width Sensor to Configuration_adv.h	7 years ago
Scott Lahteine	b76e173205	Move test extrusion options under G26	7 years ago
Scott Lahteine	81b91b3f9d	Clean up some trailing white-space	7 years ago
Roxy-3D	967104e1ce	Default Extrusion Settings were off a few lines in some of the example config files. (#8333 )	7 years ago

1 2 3 4 5 ...

837 Commits (c5730cf711aaec8f8fe46d35f66340cccd3a5f9b)