Move Filament Width Sensor to Configuration_adv.h

Marlin/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/default/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/default/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1720,38 +1720,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -1859,38 +1859,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -1708,38 +1708,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -1695,38 +1695,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -1691,38 +1691,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -1701,38 +1701,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         2.00 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.60 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -1252,6 +1252,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         2.00 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.60 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -1691,38 +1691,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -1699,38 +1699,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -1710,41 +1710,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#define DEFAULT_STDDEV_FILAMENT_DIA 0.05    // Typical estimate for cheap filament
-//#define DEFAULT_STDDEV_FILAMENT_DIA 0.02  // Typical advertised for higher quality filament
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT        (DEFAULT_NOMINAL_FILAMENT_DIA+4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT        (DEFAULT_NOMINAL_FILAMENT_DIA-4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -1255,6 +1255,43 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#define DEFAULT_STDDEV_FILAMENT_DIA 0.05    // Typical estimate for cheap filament
+//#define DEFAULT_STDDEV_FILAMENT_DIA 0.02  // Typical advertised for higher quality filament
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT        (DEFAULT_NOMINAL_FILAMENT_DIA+4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT        (DEFAULT_NOMINAL_FILAMENT_DIA-4*DEFAULT_STDDEV_FILAMENT_DIA) // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Felix/Configuration.h

@@ -1682,38 +1682,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -1682,38 +1682,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -1697,38 +1697,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -1715,40 +1715,6 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 /**
  * Customize common displays for GT2560
  */

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -1704,38 +1704,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -1728,38 +1728,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -1249,6 +1249,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -1704,38 +1704,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -1704,38 +1704,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -1259,6 +1259,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -1675,38 +1675,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -1277,6 +1277,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/SCARA/Configuration.h

@@ -1712,38 +1712,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -1703,38 +1703,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -1731,38 +1731,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -1244,6 +1244,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -1756,38 +1756,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -1701,38 +1701,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -1735,38 +1735,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -1263,6 +1263,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -1700,38 +1700,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1834,38 +1834,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         1.95 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.20 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         1.95 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.20 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1827,38 +1827,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -1822,38 +1822,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -1825,38 +1825,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -1825,38 +1825,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

@@ -1262,6 +1262,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -1834,38 +1834,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -1257,6 +1257,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -1714,38 +1714,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/makibox/Configuration.h

@@ -1703,38 +1703,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -1695,38 +1695,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -1255,6 +1255,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *

Marlin/src/config/examples/wt150/Configuration.h

@@ -1705,38 +1705,4 @@
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
-  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -1256,6 +1256,40 @@
   //#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
+ *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO       : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
+
+  #define MEASURED_UPPER_LIMIT         3.30 // (mm) Upper limit used to validate sensor reading
+  #define MEASURED_LOWER_LIMIT         1.90 // (mm) Lower limit used to validate sensor reading
+  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
 /**
  * CNC Coordinate Systems
  *