4c8330c15c
Trim Adjustments for Delta Configurations
9 years ago
962120d1d2
Fix spacing in some conditional blocks
9 years ago
20b4772155
Create DEBUG_LEVELING_FEATURE
9 years ago
194f98ff95
Debug messages for homing and leveling
10 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
9897a9147c
Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
9 years ago
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
9 years ago
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
9 years ago
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
9 years ago
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
9 years ago
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
9 years ago
d8860f9ad9
Alway end at the same point
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
9 years ago
4ca8f4a9a7
Always zigzag
Use the shortest way between probing-points.
9 years ago
3d23424121
Add array indexIntoAB[xx][yy]
and use it.
9 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
9 years ago
9d8cc24abf
Continue from the line following the M999 (PR#60)
If the printer is going to accept the M999,
then it should continue from that line number.
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
b227d8c128
Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
9 years ago
4f46df5dab
Make bootscreen configurable for the graphic displays
Saves about 473 byte of progmem and 28 bytes of RAM.
9 years ago
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
9 years ago
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
9 years ago
1f63293624
servo_endstops -> servo_endstop_id
9 years ago
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
9 years ago
ae9274be05
Fix minor compiler warnings in for loops
9 years ago
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
9 years ago
d03f037a92
Get rid of malloc() and free() (PR#2549)
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
9 years ago
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
9 years ago
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
9 years ago
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
9 years ago
ae00fad75b
Rename as M100
9 years ago
a401d738df
There is an echo in here
10 years ago
ed7d45e8f5
Memory watcher
10 years ago
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
9 years ago
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
9 years ago
e2957df05c
Shorthand for do_blocking_move_to
9 years ago
819c5b9b50
Adjust comment on Z adjustment
9 years ago
5a7356b6fc
Patch for G29 final Z position
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
9 years ago
088e09e052
Add forgotten Marlin_main.cpp
9 years ago
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
9 years ago
469843427d
Reduce code in gcode_M81 (PR#2497)
9 years ago
c66955aaf9
Mark unchanging arrays as const (PR#2494)
The compiler may be able to optimize if it knows an array won’t be
changing.
9 years ago
278aa15301
Add COUNT macro and apply
9 years ago
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
9 years ago
e83eac312e
Move plan_arc next to prepare_move
9 years ago
5c5936508d
G2/G3 Arcs for Delta
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
9 years ago
3b23ccd366
Patch servos code for move
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
9 years ago
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
9 years ago
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
to make clear - it's not a question but an order.
9 years ago
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
9 years ago
0f1df62389
Fixup comments in code_seen
10 years ago
Shane Francis
Scott Lahteine
Richard Wackerbarth
Christian Lefrançois
AnHardt
Patrick Bogen