servo_endstops -> servo_endstop_id

Marlin/Conditionals.h

@@ -513,7 +513,6 @@
 
   #define HAS_BUZZER ((defined(BEEPER) && BEEPER >= 0) || defined(LCD_USE_I2C_BUZZER))
 
-
   #if defined( NUM_SERVOS ) && (NUM_SERVOS > 0)
     #ifndef X_ENDSTOP_SERVO_NR
       #define X_ENDSTOP_SERVO_NR -1
@@ -527,6 +526,7 @@
     #if (X_ENDSTOP_SERVO_NR >= 0) || (Y_ENDSTOP_SERVO_NR >= 0) || (Z_ENDSTOP_SERVO_NR >= 0)
       #define SERVO_ENDSTOPS {X_ENDSTOP_SERVO_NR, Y_ENDSTOP_SERVO_NR, Z_ENDSTOP_SERVO_NR}
       #define HAS_SERVO_ENDSTOPS true
+      #define SERVO_ENDSTOP_IDS { X_ENDSTOP_SERVO_NR, Y_ENDSTOP_SERVO_NR, Z_ENDSTOP_SERVO_NR }
     #endif
   #endif
 

Marlin/Marlin_main.cpp

@@ -314,8 +314,8 @@ bool target_direction;
   };
 #endif
 
-  const int servo_endstops[] = SERVO_ENDSTOPS;
 #if HAS_SERVO_ENDSTOPS
+  const int servo_endstop_id[] = SERVO_ENDSTOP_IDS;
   const int servo_endstop_angles[][2] = SERVO_ENDSTOP_ANGLES;
 #endif
 
@@ -580,8 +580,8 @@ void servo_init() {
   // Set position of Servo Endstops that are defined
   #if HAS_SERVO_ENDSTOPS
     for (int i = 0; i < 3; i++)
-      if (servo_endstops[i] >= 0)
-        servo[servo_endstops[i]].move(servo_endstop_angles[i][1]);
+      if (servo_endstop_id[i] >= 0)
+        servo[servo_endstop_id[i]].move(servo_endstop_angles[i][1]);
   #endif
 
 }
@@ -1325,7 +1325,7 @@ static void setup_for_endstop_move() {
     #if HAS_SERVO_ENDSTOPS
 
       // Engage Z Servo endstop if enabled
-      if (servo_endstops[Z_AXIS] >= 0) servo[servo_endstops[Z_AXIS]].move(servo_endstop_angles[Z_AXIS][0]);
+      if (servo_endstop_id[Z_AXIS] >= 0) servo[servo_endstop_id[Z_AXIS]].move(servo_endstop_angles[Z_AXIS][0]);
 
     #elif defined(Z_PROBE_ALLEN_KEY)
       feedrate = Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE;
@@ -1415,7 +1415,7 @@ static void setup_for_endstop_move() {
     #if HAS_SERVO_ENDSTOPS
 
       // Retract Z Servo endstop if enabled
-      if (servo_endstops[Z_AXIS] >= 0) {
+      if (servo_endstop_id[Z_AXIS] >= 0) {
 
         #if Z_RAISE_AFTER_PROBING > 0
           if (doRaise) {
@@ -1425,7 +1425,7 @@ static void setup_for_endstop_move() {
         #endif
 
         // Change the Z servo angle
-        servo[servo_endstops[Z_AXIS]].move(servo_endstop_angles[Z_AXIS][1]);
+        servo[servo_endstop_id[Z_AXIS]].move(servo_endstop_angles[Z_AXIS][1]);
       }
 
     #elif defined(Z_PROBE_ALLEN_KEY)
@@ -1678,8 +1678,8 @@ static void homeaxis(AxisEnum axis) {
 
     #if HAS_SERVO_ENDSTOPS
       // Engage Servo endstop if enabled
-      if (axis != Z_AXIS && servo_endstops[axis] >= 0)
-        servo[servo_endstops[axis]].move(servo_endstop_angles[axis][0]);
+      if (axis != Z_AXIS && servo_endstop_id[axis] >= 0)
+        servo[servo_endstop_id[axis]].move(servo_endstop_angles[axis][0]);
     #endif
 
     // Set a flag for Z motor locking
@@ -1780,8 +1780,8 @@ static void homeaxis(AxisEnum axis) {
     {
       #if HAS_SERVO_ENDSTOPS
         // Retract Servo endstop if enabled
-        if (servo_endstops[axis] >= 0)
-          servo[servo_endstops[axis]].move(servo_endstop_angles[axis][1]);
+        if (servo_endstop_id[axis] >= 0)
+          servo[servo_endstop_id[axis]].move(servo_endstop_angles[axis][1]);
       #endif
     }