5cc7916e69
Add G29_RETRY_AND_RECOVER feature
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
6 years ago
4f184ba5da
[2.0.x] Add BOARD_MKS_BASE_15 with digital micro-stepping ( #10454 )
* Add BOARD_MKS_BASE_15 with digital micro-stepping
* Rename MKS_13 to MKS_GEN_13
6 years ago
39c6f65ce7
Ignore LCD_BED_LEVELING with UBL
6 years ago
c9aed73987
Fix missed includes from HAL macro patch ( #10416 )
6 years ago
cc6d41e1d3
Use a macro for HAL header redirection ( #10380 )
6 years ago
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
6 years ago
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
6 years ago
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
6 years ago
2d9b0a66fe
Add Filament Change accelerations
6 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
6 years ago
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
As suggested by @GMagician
6 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
6 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
6 years ago
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
6 years ago
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
6 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
6 years ago
49f384a2ab
Note about MKS_MINI_12864 in sanitycheck
6 years ago
f6d13e2295
Allow Z_SAFE_HOMING sanity checks to handle floats
6 years ago
1be955e52a
Alert users about low Z jerk values
6 years ago
a891af2f7a
Enforce minimum TMC2130 / TMC2208 libs
6 years ago
433e984d1f
move comment to fix compile error
6 years ago
b756a15aba
another needs to be deleted
6 years ago
50c81ebe0d
remove check that always fails
6 years ago
3ac135cef3
Enforce minimum TMC2130 / TMC2208 libs
6 years ago
97e8a6ebd9
Various fixes for DUE... ( #10152 )
- Watchdog reset during SD Card initialization.
- Move `DebugMonitor` to `DebugMonitor_Due.cpp`.
- Since the watchdog is enabled on boot do extra resets during init.
- Have `thermalManager` do watchdog reset before its ISR starts to prevent reset.
- Ensure that timers are stopped before reprogramming them to address tone issues.
- Improve SAM3XE reset when reflashed through the native port.
6 years ago
987597532c
For MK2_MULTIPLEXER undef DISABLE_INACTIVE_EXTRUDER
Fix #10098
6 years ago
dd2949922b
Consolidate 3-point leveling point options
6 years ago
1d22609473
MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS
6 years ago
d603e655d3
Fix SWITCHING_EXTRUDER manual movement
6 years ago
5f77816772
Reduce size of "only one" sanity checks
6 years ago
e7570f3195
Improve TMC config organization, naming
6 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
6 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
6 years ago
0d8c15c01f
restore PR 9661 files & V1 fix
6 years ago
bf59a4a6df
Revert "[2.0.x] DUE compatibility with shared SPI LCDs, USB mass storage, add pin defs & update examples\MakerParts\Configuration.h"
6 years ago
914bb80bde
removed SDSS init
added device & comm drivers for shared SPI LCDs
mistyped some updates in ultralcd_impl_DOGM.h
remove unwanted changes in onfiguration.h
still can't type
Update HAL_LCD_class_defines.h
include USB mass storage & misc
6 years ago
eb212ae073
Add suspend_auto_report flag to suppress auto-report
6 years ago
ffbf63e6af
Add HAS_TEMP_SENSOR conditional
6 years ago
6d7f4f84e2
Add board MKS_BASE_HEROIC ( #9926 )
Followup to #9008
- Don't define micro-stepping pins for boards that lack them.
- Allow setting of 128 microsteps with `M350`.
6 years ago
c37b3f995a
Sanity-check some graphical LCD-only options
6 years ago
c1f4112bdc
[2.0.x] Add 1284 support & misc. bug fixes ( #9864 )
6 years ago
118899357d
Add sanity checks to Linear Advance 1.5 ( #9873 )
6 years ago
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics ( #9868 )
6 years ago
8c03ce4d80
Fix Z safe homing sanity check for no probe
Fix #9851
6 years ago
3f89bbeab5
Drop a conditional only used once
6 years ago
b2cf253a13
Add RESTORE_LEVELING_AFTER_G28 option
6 years ago
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
6 years ago
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD ( #9740 )
6 years ago
c4ec01d59b
Conditionals for SWITCHING_EXTRUDER
In reference to #5367 . SWITCHING_EXTRUDER was not fully implemented for EXTRUDERS > 2.
6 years ago
d3ca82d8c2
Support for multiple filament runout sensors
6 years ago
Marcio Teixeira
Scott Lahteine
Scott Lahteine
Chris Pepper
Luc Van Daele
Yunhui Fu
Eduardo José Tagle
Sean
Lenbok
Karl Andersson
Bob-the-Kuhn
Studiodyne