aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
7 years ago
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
7 years ago
b7dfc79988
Disable SERIAL_PORT_2 by default and sanity-check it ( #10748 )
7 years ago
e978e6e782
[2.0.x] Arrange LCD options by type ( #10630 )
7 years ago
e911635fb1
Add thermocouple with AD8495 support
7 years ago
b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
7 years ago
c87b0e21be
Add units to probe speed comments
7 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
7 years ago
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
7 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
7 years ago
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
7 years ago
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
7 years ago
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
7 years ago
dca69efc11
Update Bed PID comments
7 years ago
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
7 years ago
5b3bda1c16
Add Chamber Temp options to example configs
7 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
7 years ago
dd2949922b
Consolidate 3-point leveling point options
7 years ago
c6ff39cc14
Spacing cleanup
7 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
7 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
7 years ago
79e6d890d5
Add UNKNOWN_Z_NO_RAISE to example configs
7 years ago
a2a672449a
Updated boot screen description
7 years ago
54c65fc3cb
Standardize LCD buzz defaults
7 years ago
4953fb1c88
Standardize encoder defaults
7 years ago
5684beae90
Bring some configs up to speed
7 years ago
2024775e07
Spanish (UTF8) Language ( #9786 )
From #7314 by @MrAmericanMike
7 years ago
17d984eab3
Add RESTORE_LEVELING_AFTER_G28 to example configs
7 years ago
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD ( #9740 )
7 years ago
8733d5a296
Add NUM_RUNOUT_SENSORS to example configs
7 years ago
ca55f2927a
Pulldown pin mode support ( #9701 )
Implemented for LPC1768.
7 years ago
21e60fd3ed
Allow user to control Z-Height correction for off mesh movements ( #9661 )
7 years ago
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
7 years ago
eecb0188c0
Add ULTI_CONTROLLER to example configs
7 years ago
4925f60cff
Add MALYAN_LCD to configs
7 years ago
7d6c009104
Add thermistor 15 tuned for JGAurora A5
7 years ago
348b454401
Probe bounds based on bed size
7 years ago
c68ce8667d
Fix and improve Creality configs
7 years ago
57b61491d3
Set FIL_RUNOUT_PIN for Creality CR10-S
Tested with M43 and found to be connected to DIO 2
7 years ago
4a4d832344
Use standard encoder pulses/steps for CR-10S
7 years ago
fa432508b0
Followup to Ender config
7 years ago
a27fa80a7e
More featureful CR-10S configuration
7 years ago
77c2d810f9
Bring configs up to date
7 years ago
8ac246162e
Creality CR-10S configurations
Provided by printedsolid.com
7 years ago
048486390e
Bring some configs up to date
7 years ago
5295b4713d
[2.0.x] add semitec 104NT-4 ( #9119 )
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
7 years ago
0b4a46fa6c
Bring configs up to date with 1.1.x
7 years ago
7cc2193bce
Add Tronxy X1 example config ( #8972 )
7 years ago
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
7 years ago
28fc8741d6
Reduce default jerk. XY by half. Z by 1/4
7 years ago
Scott Lahteine
Scott Lahteine
nightdemonx
KangDroid
Yunhui Fu
Roxy-3D
GMagician
Thomas Moore