bfe223e120
Adjust usage of stepper.synchronize
6 years ago
af1950a63e
Improve sync of stepper positions
6 years ago
d7b699ec34
Fewer includes of vector_3.h
6 years ago
05fca752d6
Clean up autostart handling
6 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
6 years ago
59fda986ea
Allow Z_AFTER_PROBING to be 0
6 years ago
9e0d99c0c6
Round all floats in string conversion functions ( #10566 )
6 years ago
cd08f01bb4
Fix M421 comment in gcode.h
6 years ago
8db7fb226a
Fix M420 C for UBL
6 years ago
724e9f56c8
Removed "const" to match parser. ( #10548 )
6 years ago
2e1939e85c
[2.0.x] report error on unsupported commands ( #10553 )
Raise an error when an unknown/unsupported G/M command is requires.
This will address #10546
6 years ago
a51ba6e3f6
Fix ABL grid bounds test for Delta/SCARA
Addressing #10538
6 years ago
63e0b36f8b
Fix G29_RECOVER_COMMANDS typo
6 years ago
eef0248a1c
Add M420 C to adjust the whole mesh ( #10522 )
6 years ago
02a711c4d6
[2.0.x] Fix crash upon repeated calls to process_subcommands_now_P ( #10509 )
6 years ago
f06c3c38b9
Fix M0_M1 with no LCD
6 years ago
f423e54f77
Strip trailing spaces
6 years ago
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
6 years ago
1c3d49afe0
Fix G28 with Z_AFTER_PROBING
Fix #10476
6 years ago
3396671011
[2.0.x] Reset LCD status to fallbacks ( #10470 )
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
6 years ago
11ab017dd0
Creality3D Power-Loss Recovery
6 years ago
7dcd0a1cff
Add R parameter to G28 to specify pre-raise
6 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
6 years ago
d8a8eec6ea
Add THERMAL_PROTECTION capability
Based on #10465
In response to `M115` the firmware reports if Thermal Protection is enabled (1) or not (0). This information can be used by software such as OctoPrint (more precisely the Printer Safety Check plugin) to warn users when Thermal Protection is not enabled in the firmware.
Co-Authored-By: andrivet <sebastien@advtools.com>
6 years ago
65a6a86d19
Don't report point 0 in MBL G29
6 years ago
78ea4871f9
Fix up enqueue now functions
…and apply to MALYAN_LCD.
6 years ago
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
6 years ago
df2f24617b
Use 0 as the bed position (not Z_MIN_POS)
6 years ago
52c024e260
M221 with no parameters report flow
6 years ago
0746aff595
Improve UBL mesh report. Add M420 T, M421 N
6 years ago
99282a46e9
Make sure ABL (manual) starts close to the bed
6 years ago
3c5c6d478a
Prettify process_parsed_command
6 years ago
bb7064cc30
Tweak MBL move to bed code
6 years ago
daa712455b
Make sure MBL starts close to the bed
Fix #10390
6 years ago
4c8751727a
Fix M118 parameter handling
Fix #10388
6 years ago
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
6 years ago
ac2e0afb62
Low Point for delta calibration ( #10363 )
6 years ago
2d9b0a66fe
Add Filament Change accelerations
6 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
6 years ago
cea398849e
Tweak to gcode_line_error/return
6 years ago
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
6 years ago
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
6 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
6 years ago
1a75165f35
For set_z_fade_height use set_bed_leveling_enabled
6 years ago
55e9b85ad6
Clear the "Wait for user" message set by M0/M1
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
6 years ago
c1f58a238d
No delay in sensorless quick homing ( #10254 )
6 years ago
1be955e52a
Alert users about low Z jerk values
6 years ago
9e4c037cef
Wait before turning off PRINTER_EVENT_LEDS at print end ( #10248 )
6 years ago
7b8bb2519e
Fix gcode_line_error call
Followup to 3007eee
6 years ago
aa20b3ef7c
Fix linear/3-point manual leveling buffer overrun
Fixes #10137
6 years ago
Scott Lahteine
Scott Lahteine
Marcio Teixeira
Giuliano
Luc Van Daele
Sean
AnHardt