8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
* Re-bump speed divisor should be the same for delta printer.
9 years ago
703df2cb6c
Fix error message for probe region sanity check
9 years ago
4c8330c15c
Trim Adjustments for Delta Configurations
9 years ago
962120d1d2
Fix spacing in some conditional blocks
9 years ago
20b4772155
Create DEBUG_LEVELING_FEATURE
10 years ago
194f98ff95
Debug messages for homing and leveling
10 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)
reads better than
10 years ago
91fd66ffba
add Lulzbot TAZ4 example configuration (PR#104)
10 years ago
7a275773ee
remove colon in utf_mapper.h (PR#106)
9 years ago
6b4b6fa315
update for newest version of U8glib_Arduino
9 years ago
9897a9147c
Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
9 years ago
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
* Fix a couple of renames omission and macro expansion errors.
9 years ago
ad90e851b3
Use a small unsigned integer type
10 years ago
29b456ae07
Suppress some compiler warnings
10 years ago
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
10 years ago
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
10 years ago
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
10 years ago
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
10 years ago
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
10 years ago
d8860f9ad9
Alway end at the same point
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
10 years ago
4ca8f4a9a7
Always zigzag
Use the shortest way between probing-points.
10 years ago
3d23424121
Add array indexIntoAB[xx][yy]
and use it.
10 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
10 years ago
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
10 years ago
e09ff79635
Update pins_RAMPS_13.h (PR#64)
Now all ramps configuration can enable Filament sensor not only EEB
10 years ago
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
10 years ago
9d8cc24abf
Continue from the line following the M999 (PR#60)
If the printer is going to accept the M999,
then it should continue from that line number.
10 years ago
f3ab1dba54
Z babystepping for coreXY (PR#47)
only X and Y were not implemented
10 years ago
35afea1c0e
Restore test
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
10 years ago
6af75f4b5d
Squish down deprecated tests in sanity check
10 years ago
edeb58288e
Use PIN_EXISTS in sanity check
10 years ago
c30b7693e0
Clean up RUMBA pins conditions
10 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
10 years ago
b227d8c128
Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
10 years ago
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
10 years ago
4e2f5618c1
Pick up Default_version when needed
10 years ago
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
10 years ago
5a11d32a85
Move deprecation test to SanityCheck.h
10 years ago
7bb7a52940
Bring config up-to-date
10 years ago
244ea2014a
Boot-screen for text-displays improvements
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
10 years ago
80f2a20842
Enable bootscreen in all Configurations
10 years ago
2684d061ed
Scroll too long strings on bootscreen
10 years ago
4f46df5dab
Make bootscreen configurable for the graphic displays
Saves about 473 byte of progmem and 28 bytes of RAM.
10 years ago
09571b7753
Boot-screen for the character displays
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
10 years ago
866efc14fe
Add Danish translations
10 years ago
267f3479d7
Adjust spacing in pins_RAMPS_13.h
10 years ago
56702e7bb9
Define servo pins just like other pins
10 years ago
4b9d5cd352
Use lowercase names for serial instances
10 years ago
1e2deff4fd
Rename BTENABLED to BLUETOOTH
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
10 years ago
68055a5959
Include RIGIDBOT_PANEL in Conditionals
10 years ago
Christian Lefrançois
Scott Lahteine
Shane Francis
Richard Wackerbarth
Richard Marko
Wurstnase
Chris Bruner
AnHardt
RicardoGA
Fourmi