1b6bc19427
Add external closed loop controller support
6 years ago
beb51c2d58
Show manual extrusion moves as relative in LCD
- Implements FR#11724
- Old behavior can be restored by commenting out MANUAL_E_MOVES_RELATIVE
6 years ago
e3fc9aa35f
Update some config comments
6 years ago
f8c52c9c29
Azteeg X5 Mini WiFi support ( #11601 )
6 years ago
2d3317a35b
Prettify Dual X Carriage description
6 years ago
a1a5367380
Smoothieboard V1.0/1.1 and A5984 support
6 years ago
9c62c47579
[2.0.x] Fix Dual X Carriage tool change crash ( #11447 )
6 years ago
fbcdf5eaeb
Simplify stepper driver per-axis selection
6 years ago
9660996cc3
Add Multi Unit Support for Max7219 to bugfix_2.0.0 ( #11285 )
* Add Multi Unit Support for Max7219 to bugfix_2.0.0
* Apply multi-MAX7219 to example configs
* Tweak some spacing, macros
6 years ago
665ac1e4d0
Add POWER_LOSS_PIN support
6 years ago
e0ab8acf19
Add "Marlin Dev Mode" option
7 years ago
bd7f5848f1
Remove JUNCTION_DEVIATION_INCLUDE_E option ( #11147 )
7 years ago
5b49fccf80
Add stepper driver DIR delay configuration option
...and recommended pulse width configuration for A4988
7 years ago
d4795e5b8e
[2.0.x] Tweaks and additions for MAX7219 ( #11034 )
7 years ago
e2aeda61ed
HAL for Espressif ESP32 Wifi
7 years ago
6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
7 years ago
39a7e7720d
Adaptive multiaxis step smoothing
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
7 years ago
8a376e6beb
Update MINIMUM_STEPPER_PULSE description
7 years ago
2deff0d9b9
Fix/Improve junction deviation
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
7 years ago
2e139fe50f
Tweak configuration spacing
7 years ago
931ab4ec40
Rename Junction Deviation options
7 years ago
43ddb29f9e
Add FAN_MAX_PWM for M106-controlled fans
7 years ago
acacee80a2
Add JUNCTION_ACCELERATION_FACTOR to configs
Part of #10688
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
4d4bf7897d
Junction Deviation jerk limiting option
7 years ago
840ff60952
Bring some configs up to date
7 years ago
e911635fb1
Add thermocouple with AD8495 support
7 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
7 years ago
11ab017dd0
Creality3D Power-Loss Recovery
7 years ago
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
7 years ago
2d9b0a66fe
Add Filament Change accelerations
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
2fa0a73c2c
Implement filament change continuous purge
7 years ago
1d22609473
MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS
7 years ago
c24dbcbfe1
When STATUS_EXPIRE_SECONDS is 0, hide the position. ( #10081 )
Some users may prefer to hide the position updates on the `LIGHTWEIGHT_UI` altogether. This leads to an even less cluttered display (it also saves on SPI traffic and one byte of RAM).
7 years ago
e7a61de8af
[2.0] FWRetract Reset (Best way) ( #10083 )
7 years ago
e7570f3195
Improve TMC config organization, naming
7 years ago
6b4a928145
2uS default step pulse ( #9989 )
7 years ago
94f5204629
Move AUTO_REPORT_SD_STATUS to SDSUPPORT block
7 years ago
b198b49d15
Followup to AUTO_REPORT_SD_STATUS
Followup to #9832
7 years ago
23a576faf7
[2.0] Fix for FW retract ( #9878 )
7 years ago
b8485528b2
Prettify LCD_PROGRESS_BAR options
7 years ago
e65a853c59
Fix LCD_PROGRESS_BAR
Fix #9208
7 years ago
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
7 years ago
532bb3aaa1
Lightweight status screen for ST7920
- This status screen uses the ST7920 character generator to greatly
reduce SPI traffic and MCU load when updating the status screen.
- Has been tested with the RepRapDiscount Full Graphics Smart Controller
but should work with any LCD that uses an ST7920 or fully compatible
controller.
7 years ago
59c98d6fd5
Hephestos2 heated bed kit for all ( #9757 )
7 years ago
79272f98fc
Proposed changes to ST7920 lightweight status screen
7 years ago
9019ea0fce
Option to force X or Y to home first when homing the other axis
7 years ago
330437ad7c
Update LCD_SET_PROGRESS_MANUALLY in configs
7 years ago
349dafa728
config update (set to -1)
7 years ago
5b70d3da1c
Update DIGIPOT_I2C_MOTOR_CURRENTS comments
7 years ago
Sam Lane
Marcio Teixeira
Scott Lahteine
Michael Triffon
Greg Nutt
Scott Lahteine
teemuatlut
Roxy-3D
etagle
Simon Jouet
Jiri Jaburek
nightdemonx
Sean
Lenbok
Studiodyne
Bob-the-Kuhn
Kevin
blye