andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Merge pull request #2868 from esenapaj/esenapaj-patch-1 

Fix AUTOTEMP documentation in configs
pull/1/head
Scott Lahteine 9 years ago
parent
159ff94afd 27d918d836
commit
b03787262a
11 changed files with 110 additions and 198 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Unified View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 28
      Marlin/example_configurations/Felix/Configuration_adv.h
  2. 28
      Marlin/example_configurations/Hephestos/Configuration_adv.h
  3. 28
      Marlin/example_configurations/K8200/Configuration_adv.h
  4. 28
      Marlin/example_configurations/SCARA/Configuration_adv.h
  5. 28
      Marlin/example_configurations/WITBOX/Configuration_adv.h
  6. 28
      Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
  7. 28
      Marlin/example_configurations/delta/generic/Configuration_adv.h
  8. 28
      Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
  9. 28
      Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
  10. 28
      Marlin/example_configurations/makibox/Configuration_adv.h
  11. 28
      Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

28
Marlin/example_configurations/Felix/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/Hephestos/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/K8200/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/SCARA/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/WITBOX/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/delta/generic/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
View File

@ -40,16 +40,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -60,14 +50,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/makibox/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

28
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
View File

@ -36,16 +36,6 @@
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
/**
* Automatic Temperature:
* The hotend target temperature is calculated by all the buffered lines of gcode.
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98

Write Preview
Loading…
Cancel
Save