Browse Source

Support FYSETC_MINI_12864 on Re-ARM, RAMPS_FD, MKS SBASE (#13717)

pull/1/head
Bob Kuhn 6 years ago
committed by Scott Lahteine
parent
commit
9b578ca343
  1. 68
      Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp
  2. 2
      Marlin/src/inc/Conditionals_LCD.h
  3. 6
      Marlin/src/lcd/dogm/ultralcd_DOGM.h
  4. 35
      Marlin/src/pins/pins_MKS_SBASE.h
  5. 5
      Marlin/src/pins/pins_RAMPS_FD_V1.h
  6. 41
      Marlin/src/pins/pins_RAMPS_RE_ARM.h

68
Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp

@ -65,10 +65,76 @@
#undef SPI_SPEED #undef SPI_SPEED
#define SPI_SPEED 2 // About 2 MHz #define SPI_SPEED 2 // About 2 MHz
#include <algorithm>
#include <LPC17xx.h>
#include <gpio.h>
#include <Arduino.h>
uint8_t swSpiTransfer_mode_0(uint8_t b, const uint8_t spi_speed, const pin_t sck_pin, const pin_t miso_pin, const pin_t mosi_pin ) {
for (uint8_t i = 0; i < 8; i++) {
if (spi_speed == 0) {
gpio_set(mosi_pin, !!(b & 0x80));
gpio_set(sck_pin, HIGH);
b <<= 1;
if (miso_pin >= 0 && gpio_get(miso_pin)) b |= 1;
gpio_set(sck_pin, LOW);
}
else {
const uint8_t state = (b & 0x80) ? HIGH : LOW;
for (uint8_t j = 0; j < spi_speed; j++)
gpio_set(mosi_pin, state);
for (uint8_t j = 0; j < spi_speed + (miso_pin >= 0 ? 0 : 1); j++)
gpio_set(sck_pin, HIGH);
b <<= 1;
if (miso_pin >= 0 && gpio_get(miso_pin)) b |= 1;
for (uint8_t j = 0; j < spi_speed; j++)
gpio_set(sck_pin, LOW);
}
}
return b;
}
uint8_t swSpiTransfer_mode_3(uint8_t b, const uint8_t spi_speed, const pin_t sck_pin, const pin_t miso_pin, const pin_t mosi_pin ) {
for (uint8_t i = 0; i < 8; i++) {
const uint8_t state = (b & 0x80) ? HIGH : LOW;
if (spi_speed == 0) {
gpio_set(sck_pin, LOW);
gpio_set(mosi_pin, state);
gpio_set(mosi_pin, state); // need some setup time
gpio_set(sck_pin, HIGH);
}
else {
for (uint8_t j = 0; j < spi_speed + (miso_pin >= 0 ? 0 : 1); j++)
gpio_set(sck_pin, LOW);
for (uint8_t j = 0; j < spi_speed; j++)
gpio_set(mosi_pin, state);
for (uint8_t j = 0; j < spi_speed; j++)
gpio_set(sck_pin, HIGH);
}
b <<= 1;
if (miso_pin >= 0 && gpio_get(miso_pin)) b |= 1;
}
return b;
}
static uint8_t SPI_speed = 0; static uint8_t SPI_speed = 0;
static void u8g_sw_spi_HAL_LPC1768_shift_out(uint8_t dataPin, uint8_t clockPin, uint8_t val) { static void u8g_sw_spi_HAL_LPC1768_shift_out(uint8_t dataPin, uint8_t clockPin, uint8_t val) {
swSpiTransfer(val, SPI_speed, clockPin, -1, dataPin); #if ENABLED(FYSETC_MINI_12864)
swSpiTransfer_mode_3(val, SPI_speed, clockPin, -1, dataPin);
#else
swSpiTransfer_mode_0(val, SPI_speed, clockPin, -1, dataPin);
#endif
} }
uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) { uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {

2
Marlin/src/inc/Conditionals_LCD.h

@ -143,6 +143,8 @@
#define DOGLCD #define DOGLCD
#define ULTIPANEL #define ULTIPANEL
#define LCD_CONTRAST_MIN 0
#define LCD_CONTRAST_MAX 255
#define DEFAULT_LCD_CONTRAST 255 #define DEFAULT_LCD_CONTRAST 255
#define LED_COLORS_REDUCE_GREEN #define LED_COLORS_REDUCE_GREEN

6
Marlin/src/lcd/dogm/ultralcd_DOGM.h

@ -112,7 +112,11 @@
//#define U8G_CLASS U8GLIB_MINI12864 //#define U8G_CLASS U8GLIB_MINI12864
//#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes //#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes
#define U8G_CLASS U8GLIB_MINI12864_2X #define U8G_CLASS U8GLIB_MINI12864_2X
#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes #if EITHER(FYSETC_MINI_12864, TARGET_LPC1768)
#define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI
#else
#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI
#endif
#elif ENABLED(U8GLIB_SH1106_EINSTART) #elif ENABLED(U8GLIB_SH1106_EINSTART)
// Connected via motherboard header // Connected via motherboard header
#define U8G_CLASS U8GLIB_SH1106_128X64 #define U8G_CLASS U8GLIB_SH1106_128X64

35
Marlin/src/pins/pins_MKS_SBASE.h

@ -253,6 +253,41 @@
#define DOGLCD_SCK SCK_PIN #define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN #define DOGLCD_MOSI MOSI_PIN
#endif #endif
#if ENABLED(FYSETC_MINI_12864)
/**
* The Fysetc display can NOT use the SCK and MOSI pins on EXP2, so a
* special cable is needed to go between EXP2 on the FYSETC and the
* controller board's EXP2 and J8. It also means that a software SPI
* is needed to drive those pins.
*
* The Fysetc requires mode 3 SPI interface.
*
* Pins 6, 7 & 8 on EXP2 are no connects. That means a second special
* cable will be needed if the RGB LEDs are to be active.
*/
#define DOGLCD_CS LCD_PINS_ENABLE // EXP1.3 (LCD_EN on Fysetc schematic)
#define DOGLCD_A0 LCD_PINS_RS // EXP1.4 (LCD_A0 on Fysetc schematic)
#define DOGLCD_SCK P2_11 // J8-5 (SCK on Fysetc schematic)
#define DOGLCD_MOSI P4_28 // J8-6 (MOSI on Fysetc schematic)
#define RGB_LED
//#define RGBW_LED
#if EITHER(RGB_LED, RGBW_LED)
#define RGB_LED_R_PIN P2_12 // J8-4 (LCD_D6 on Fysetc schematic)
#define RGB_LED_G_PIN P1_23 // J8-3 (LCD_D5 on Fysetc schematic)
#define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on Fysetc schematic)
//#define RGB_LED_W_PIN -1
#endif
#elif ENABLED(MINIPANEL)
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#endif
#endif #endif
/** /**

5
Marlin/src/pins/pins_RAMPS_FD_V1.h

@ -156,7 +156,10 @@
#define LCD_PINS_D7 29 #define LCD_PINS_D7 29
#endif #endif
#if ENABLED(MINIPANEL) #if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_CS LCD_PINS_ENABLE
#define DOGLCD_A0 LCD_PINS_RS
#elif ENABLED(MINIPANEL)
#define DOGLCD_CS 25 #define DOGLCD_CS 25
#define DOGLCD_A0 27 #define DOGLCD_A0 27
#endif #endif

41
Marlin/src/pins/pins_RAMPS_RE_ARM.h

@ -269,11 +269,21 @@
#elif ENABLED(ULTRA_LCD) #elif ENABLED(ULTRA_LCD)
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
#if ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN P1_01
#define BTN_ENC P1_04
#else
#define BEEPER_PIN P1_30 // (37) not 5V tolerant #define BEEPER_PIN P1_30 // (37) not 5V tolerant
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#endif
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4
@ -296,13 +306,6 @@
#if ANY(VIKI2, miniVIKI) #if ANY(VIKI2, miniVIKI)
// #define LCD_SCREEN_ROT_180 // #define LCD_SCREEN_ROT_180
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define DOGLCD_CS P0_16 // (16) #define DOGLCD_CS P0_16 // (16)
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
#define DOGLCD_SCK SCK_PIN #define DOGLCD_SCK SCK_PIN
@ -311,8 +314,17 @@
#define STAT_LED_BLUE_PIN P0_26 //(63) may change if cable changes #define STAT_LED_BLUE_PIN P0_26 //(63) may change if cable changes
#define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
#else #else
#if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_SCK P0_15
#define DOGLCD_MOSI P0_18
#define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals
#define DOGLCD_A0 P1_14
#else
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
#endif
#define LCD_BACKLIGHT_PIN P0_16 //(16) J3-7 & AUX-4 - only used on DOGLCD controllers #define LCD_BACKLIGHT_PIN P0_16 //(16) J3-7 & AUX-4 - only used on DOGLCD controllers
#define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
#define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
@ -323,11 +335,6 @@
#endif #endif
#endif #endif
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
#if ENABLED(MINIPANEL) #if ENABLED(MINIPANEL)
// GLCD features // GLCD features
// Uncomment screen orientation // Uncomment screen orientation
@ -362,10 +369,10 @@
#if ENABLED(LPC_SD_LCD) #if ENABLED(LPC_SD_LCD)
#define SCK_PIN P0_15 #define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
#define MISO_PIN P0_17 #define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
#define MOSI_PIN P0_18 #define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
#define SS_PIN P1_23 // Chip select for SD card used by Marlin #define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#elif ENABLED(LPC_SD_ONBOARD) #elif ENABLED(LPC_SD_ONBOARD)

Loading…
Cancel
Save