Browse Source

Updated bq Hephestos 2 example configuration

pull/1/head
João Brázio 8 years ago
parent
commit
3f75edb1d6
  1. 46
      Marlin/example_configurations/Hephestos_2/Configuration.h
  2. 22
      Marlin/example_configurations/Hephestos_2/Configuration_adv.h
  3. 1
      Marlin/example_configurations/Hephestos_2/README.md
  4. 12
      Marlin/pins_BQ_ZUM_MEGA_3D.h

46
Marlin/example_configurations/Hephestos_2/Configuration.h

@ -122,7 +122,7 @@
* *
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000] * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
*/ */
#define BAUDRATE 250000 #define BAUDRATE 115200
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -190,7 +190,7 @@
* *
* :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
*/ */
#define POWER_SUPPLY 1 #define POWER_SUPPLY 0
#if POWER_SUPPLY > 0 #if POWER_SUPPLY > 0
// Enable this option to leave the PSU off at startup. // Enable this option to leave the PSU off at startup.
@ -308,7 +308,7 @@
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with gcode: M301 E[extruder number, 0-2] // Set/get with gcode: M301 E[extruder number, 0-2]
#define PID_FUNCTIONAL_RANGE 250 // If the temperature difference between the target temperature and the actual temperature #define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define K1 0.95 //smoothing factor within the PID #define K1 0.95 //smoothing factor within the PID
@ -457,7 +457,7 @@
// Enable this feature if all enabled endstop pins are interrupt-capable. // Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
//#define ENDSTOP_INTERRUPTS_FEATURE #define ENDSTOP_INTERRUPTS_FEATURE
//============================================================================= //=============================================================================
//============================== Movement Settings ============================ //============================== Movement Settings ============================
@ -480,7 +480,7 @@
* Override with M92 * Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3]]] * X, Y, Z, E0 [, E1[, E2[, E3]]]
*/ */
#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 210.02 } #define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 204 }
/** /**
* Default Max Feed Rate (mm/s) * Default Max Feed Rate (mm/s)
@ -495,7 +495,7 @@
* Override with M201 * Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3]]] * X, Y, Z, E0 [, E1[, E2[, E3]]]
*/ */
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 20, 1000 } #define DEFAULT_MAX_ACCELERATION { 800, 800, 20, 1000 }
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
@ -505,8 +505,8 @@
* M204 R Retract Acceleration * M204 R Retract Acceleration
* M204 T Travel Acceleration * M204 T Travel Acceleration
*/ */
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves #define DEFAULT_ACCELERATION 800 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts #define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
/** /**
@ -517,10 +517,10 @@
* When changing speed and direction, if the difference is less than the * When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously. * value set here, it may happen instantaneously.
*/ */
#define DEFAULT_XJERK 20.0 #define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK 20.0 #define DEFAULT_YJERK 10.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 2.0 #define DEFAULT_EJERK 1.0
//=========================================================================== //===========================================================================
@ -625,11 +625,11 @@
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// The Z_MIN_PIN will then be used for both Z-homing and probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// To use a probe you must enable one of the two options above! // To use a probe you must enable one of the two options above!
@ -650,7 +650,7 @@
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
*/ */
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_DEPLOY_PROBE 0 // Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points #define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points
// //
@ -880,8 +880,8 @@
#endif #endif
// Homing speeds (mm/m) // Homing speeds (mm/m)
#define HOMING_FEEDRATE_XY (150*60) #define HOMING_FEEDRATE_XY (60*60)
#define HOMING_FEEDRATE_Z 200 #define HOMING_FEEDRATE_Z 120
//============================================================================= //=============================================================================
//============================= Additional Features =========================== //============================= Additional Features ===========================
@ -911,7 +911,7 @@
// every couple of seconds when it can't accept commands. // every couple of seconds when it can't accept commands.
// //
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. #define DEFAULT_KEEPALIVE_INTERVAL 10 // Number of seconds between "busy" messages. Set with M113.
// //
// M100 Free Memory Watcher // M100 Free Memory Watcher
@ -956,11 +956,11 @@
// P2: The nozzle height will be raised by Z-park amount but never going over // P2: The nozzle height will be raised by Z-park amount but never going over
// the machine's limit of Z_MAX_POS. // the machine's limit of Z_MAX_POS.
// //
//#define NOZZLE_PARK_FEATURE #define NOZZLE_PARK_FEATURE
#if ENABLED(NOZZLE_PARK_FEATURE) #if ENABLED(NOZZLE_PARK_FEATURE)
// Specify a park position as { X, Y, Z } // Specify a park position as { X, Y, Z }
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 10 }
#endif #endif
// //
@ -997,18 +997,18 @@
// Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
// may change to add new functionality like different wipe patterns. // may change to add new functionality like different wipe patterns.
// //
//#define NOZZLE_CLEAN_FEATURE #define NOZZLE_CLEAN_FEATURE
#if ENABLED(NOZZLE_CLEAN_FEATURE) #if ENABLED(NOZZLE_CLEAN_FEATURE)
// Number of pattern repetitions // Number of pattern repetitions
#define NOZZLE_CLEAN_STROKES 12 #define NOZZLE_CLEAN_STROKES 12
// Specify positions as { X, Y, Z } // Specify positions as { X, Y, Z }
#define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} #define NOZZLE_CLEAN_START_POINT { X_MIN_POS + 10, Y_MAX_POS - 9, (Z_MIN_POS + 0.5)}
#define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} #define NOZZLE_CLEAN_END_POINT { X_MIN_POS + 90, Y_MAX_POS - 0, (Z_MIN_POS + 0.5)}
// Moves the nozzle to the initial position // Moves the nozzle to the initial position
#define NOZZLE_CLEAN_GOBACK //#define NOZZLE_CLEAN_GOBACK
#endif #endif
// //

22
Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@ -171,7 +171,7 @@
// Extruder runout prevention. // Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP // If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS. // then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT #define EXTRUDER_RUNOUT_PREVENT
#if ENABLED(EXTRUDER_RUNOUT_PREVENT) #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190 #define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30 #define EXTRUDER_RUNOUT_SECONDS 30
@ -335,7 +335,7 @@
#define Y_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5
#define Z_HOME_BUMP_MM 2 #define Z_HOME_BUMP_MM 2
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate) #define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. #define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
// When G28 is called, this option will make Y home before X // When G28 is called, this option will make Y home before X
#define HOME_Y_BEFORE_X #define HOME_Y_BEFORE_X
@ -369,7 +369,7 @@
#if ENABLED(ULTIPANEL) #if ENABLED(ULTIPANEL)
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder //#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
#endif #endif
// @section extras // @section extras
@ -420,10 +420,10 @@
// @section lcd // @section lcd
// Include a page of printer information in the LCD Main Menu // Include a page of printer information in the LCD Main Menu
//#define LCD_INFO_MENU #define LCD_INFO_MENU
// On the Info Screen, display XY with one decimal place when possible // On the Info Screen, display XY with one decimal place when possible
//#define LCD_DECIMAL_SMALL_XY #define LCD_DECIMAL_SMALL_XY
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
@ -440,7 +440,7 @@
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
// using: // using:
#define MENU_ADDAUTOSTART //#define MENU_ADDAUTOSTART
// Show a progress bar on HD44780 LCDs for SD printing // Show a progress bar on HD44780 LCDs for SD printing
//#define LCD_PROGRESS_BAR //#define LCD_PROGRESS_BAR
@ -470,7 +470,7 @@
#if ENABLED(DOGLCD) #if ENABLED(DOGLCD)
// A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
//#define USE_BIG_EDIT_FONT #define USE_BIG_EDIT_FONT
// A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
@ -527,7 +527,7 @@
// interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from // interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
// draining. // draining.
// //
//#define ENSURE_SMOOTH_MOVES #define ENSURE_SMOOTH_MOVES
#if ENABLED(ENSURE_SMOOTH_MOVES) #if ENABLED(ENSURE_SMOOTH_MOVES)
//#define ALWAYS_ALLOW_MENU // If enabled, the menu will always be responsive. //#define ALWAYS_ALLOW_MENU // If enabled, the menu will always be responsive.
// WARNING: Menu navigation during short moves may cause stuttering! // WARNING: Menu navigation during short moves may cause stuttering!
@ -622,9 +622,9 @@
// The number of linear motions that can be in the plan at any give time. // The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller #define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else #else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer #define BLOCK_BUFFER_SIZE 64 // maximize block buffer
#endif #endif
// @section serial // @section serial
@ -640,7 +640,7 @@
// For debug-echo: 128 bytes for the optimal speed. // For debug-echo: 128 bytes for the optimal speed.
// Other output doesn't need to be that speedy. // Other output doesn't need to be that speedy.
// :[0, 2, 4, 8, 16, 32, 64, 128, 256] // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
#define TX_BUFFER_SIZE 0 #define TX_BUFFER_SIZE 32
// Enable an emergency-command parser to intercept certain commands as they // Enable an emergency-command parser to intercept certain commands as they
// enter the serial receive buffer, so they cannot be blocked. // enter the serial receive buffer, so they cannot be blocked.

1
Marlin/example_configurations/Hephestos_2/README.md

@ -12,3 +12,4 @@ NOTE: The look and feel of the Hephestos 2 while navigating the LCD menu will ch
SD printing now disables the heater when finished SD printing now disables the heater when finished
* 2016/07/13 - Update the `DEFAULT_AXIS_STEPS_PER_UNIT` for the Z axis * 2016/07/13 - Update the `DEFAULT_AXIS_STEPS_PER_UNIT` for the Z axis
Increased the `DEFAULT_XYJERK` Increased the `DEFAULT_XYJERK`
* 2016/12/13 - Configuration updated.

12
Marlin/pins_BQ_ZUM_MEGA_3D.h

@ -83,3 +83,15 @@
// //
#undef PS_ON_PIN // 12 #undef PS_ON_PIN // 12
#define PS_ON_PIN 81 // External Power Supply #define PS_ON_PIN 81 // External Power Supply
// This board has headers for Z-min, Z-max and IND_S_5V *but* as the bq team
// decided to ship the printer only with the probe and no additional Z-min
// endstop and the instruction manual advises the user to connect the probe to
// IND_S_5V the option Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN will not work.
#ifdef Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
#define Z_MIN_PIN 19 // IND_S_5V
#define Z_MAX_PIN 18 // Z-MIN Label
#endif

Loading…
Cancel
Save