Browse Source

Improve SKR mini E3 + Ender 3 settings (#16247)

pull/1/head
salami738 5 years ago
committed by Scott Lahteine
parent
commit
329f5b4df9
  1. 2
      config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h
  2. 14
      config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h
  3. 12
      config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h

2
config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h

@ -2090,7 +2090,7 @@
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
* M913 X/Y/Z/E to live tune the setting
*/
//#define HYBRID_THRESHOLD
#define HYBRID_THRESHOLD
#define X_HYBRID_THRESHOLD 100 // [mm/s]
#define X2_HYBRID_THRESHOLD 100

14
config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h

@ -498,7 +498,7 @@
* heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
*/
//#define PIDTEMPBED
#define PIDTEMPBED
//#define BED_LIMIT_SWITCHING
@ -516,9 +516,9 @@
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 10.00
#define DEFAULT_bedKi .023
#define DEFAULT_bedKd 305.4
//#define DEFAULT_bedKp 10.00
//#define DEFAULT_bedKi .023
//#define DEFAULT_bedKd 305.4
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from pidautotune
@ -527,6 +527,10 @@
//#define DEFAULT_bedKd 1675.16
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#define DEFAULT_bedKp 50.71
#define DEFAULT_bedKi 9.88
#define DEFAULT_bedKd 173.43
#endif // PIDTEMPBED
// @section extruder
@ -1199,7 +1203,7 @@
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
// Set the number of grid points per dimension.
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Probe along the Y axis, advancing X after each column

12
config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h

@ -1150,7 +1150,7 @@
*
* :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
*/
//#define SDCARD_CONNECTION LCD
#define SDCARD_CONNECTION ONBOARD
#endif
#endif // SDSUPPORT
@ -1573,16 +1573,16 @@
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
#if ENABLED(SDSUPPORT)
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#define BLOCK_BUFFER_SIZE 32 // maximize block buffer
#endif
// @section serial
// The ASCII buffer for serial input
#define MAX_CMD_SIZE 96
#define BUFSIZE 4
#define BUFSIZE 32
// Transmission to Host Buffer Size
// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@ -1591,7 +1591,7 @@
// For debug-echo: 128 bytes for the optimal speed.
// Other output doesn't need to be that speedy.
// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
#define TX_BUFFER_SIZE 0
#define TX_BUFFER_SIZE 32
// Host Receive Buffer Size
// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
@ -2090,7 +2090,7 @@
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
* M913 X/Y/Z/E to live tune the setting
*/
//#define HYBRID_THRESHOLD
#define HYBRID_THRESHOLD
#define X_HYBRID_THRESHOLD 100 // [mm/s]
#define X2_HYBRID_THRESHOLD 100

Loading…
Cancel
Save