912704a0d8
Enable ISRs inside temperature ISR
to capture chars at UART at 250000 baud.
8 years ago
00662b8635
Minor babystep cleanup patches
8 years ago
24f6612551
Reduce and optimize endstop_monitor code
8 years ago
c7f1f0dae6
Add endstop monitor & make pins report pretty
8 years ago
9cbedab91b
Use DPM where possible
8 years ago
b6aa894893
Rename auto fan pins and add auto fan flags
8 years ago
2aa12d78dc
Only issue MAXTEMP when heating
8 years ago
70e287ca8c
Extend measuring range of thermocouple for MAX31855
8 years ago
f888597197
Reduce, clean up code for mintemp/maxtemp tests
8 years ago
ad64723354
Move MAX_EXTRUDERS to pins.h
8 years ago
385bd8a4a3
Fix freezing and MINTEMP Error with MAX31855 thermocouple
8 years ago
149b8d9e4b
Handle MAX31855 error conditions
8 years ago
1e551c0688
Revert "Squashed - Removal of PID functional range"
8 years ago
3752d9aca8
Fix timer comments
8 years ago
c63cb45268
Fix thermal runaway timeout
8 years ago
d80a79eb77
Use right-shift instead of / 2, why not?
8 years ago
02fe9cf558
Removal of functional range constraint
Also lined up the >> 1 and / 2 mentioned earlier in the unconstrained I term issue,
8 years ago
761593b74b
Cleanup some vars, use of min/max
8 years ago
1a2f1d4974
Update temperature.cpp
8 years ago
16461900c2
Fix for HEATERS_PARALLEL
8 years ago
076f3a8284
unsigned char => uint8_t
8 years ago
6ac9d895ca
Tweak Filament Width variables
8 years ago
e9bfca5870
Additional comments for Temperature::isr
8 years ago
37ac540a26
Fix unsigned/signed comparison in fanPin loop
8 years ago
1749a7fae3
Suppress warning
8 years ago
2f223b8c79
Use ABC and XYZ for "3"
8 years ago
01d4703429
PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
8 years ago
3a0a94b21a
Always init configured fan pins
8 years ago
c63003ed3e
Use matching auto-fan flags
8 years ago
3475fd7b0f
Init PWM-able auto fan pins with `SET_OUTPUT`
8 years ago
abf9696db1
Loop fan-pins based on array size
8 years ago
e88575c8ec
Init next_auto_fan_check_ms to zero
8 years ago
b63d70b186
Fix serial output for MBL, M303
8 years ago
b7b5b50a84
Throw bed min temp error only if heating
8 years ago
d3ba878f70
Drop intermediate float in HEATER_0_USES_MAX6675 test
8 years ago
3e8f9ecd1c
Extend min/max_temp_error for the bed
8 years ago
aa9b52b2e7
MISO is an input
8 years ago
9ab94bd2c1
fix-babysrepping
8 years ago
63fd1f49a6
PID_EXTRUSION_SCALING, disabled by default
8 years ago
e4942d2163
Switch SD2cadrLib to fastio
Replace all fastDigitalRead/Write() with READ/WRITE()
Define SCK_PIN, MISO_PIN, MOSI_PIN in pins.h if not already defined in the pins_*.h files.
Remove these conditional pin definitions from the pin-files. They are now always defined.
Define separate sets of SPI-pins for AT90USB with and without Teensy support in fastio.h.
Likely this was the main reason for all that confusion about the AT90USB-SPI pins.
8 years ago
2d378fac1b
No need to include thermistortables.h in Configuration.h
8 years ago
d8f2876753
Replace some float division with multiplication
8 years ago
f8b5749235
Replace division in planner with multiplication
8 years ago
3ebad4e020
Moves all global enums to a central file
8 years ago
c2c8ab4698
Follow-up the PR #4278 (Fixups for PID_ADD_EXTRUSION_RATE and HOTENDS==1)
8 years ago
cdd77d23bb
Neaten up temperature member data
9 years ago
d4c68279c8
Add "P" parameter to M302
9 years ago
11dcbae7a2
Only a single E axis. Can tool-change reseed position[E_AXIS]?
8 years ago
182c8d7f8f
Dyze High Temp Thermistor Support
9 years ago
ee0983ab57
Further reduction when HOTENDS == 1
9 years ago
Sebastianv650
Scott Lahteine
Bob-the-Kuhn
Benoit Miller
esenapaj
Scott Lahteine
Rerouter
AnHardt
João Brázio