fce1e843b9
Patch steps rate comment in trapezoid function
8 years ago
a4062a47ac
Rename baricuda variables
8 years ago
e087a99a10
Some cleanup of st_get_pos functions
8 years ago
386140f361
Test time difference in safe way
8 years ago
1b7356b3a1
Account for home_offset in G29 handler
8 years ago
865dcf3fb4
Fix FILAMENT_WIDTH_SENSOR measurement
Only measure and store filament width when E is going forward.
8 years ago
1a79b13b7a
FILAMENT_SENSOR -> FILAMENT_WIDTH_SENSOR
8 years ago
05765fb570
Add DEBUGGING macro
8 years ago
3252df7998
Minor cleanup to filament sensor code
8 years ago
0da744b7b0
Further cleanup of comments, partial Doxygen-style
Following up on #3231
8 years ago
5e5d250832
Added gplv3 header to all Marlin files
8 years ago
ba4eebad2f
Fix Fan KICKSTART
Sorting ot what else belongs to what if was not so hard.
But the static `ms = ms = millis();` was a bit surpising.
8 years ago
4bbea5124d
Support for multiple PWM fans
8 years ago
6e1bc03d3b
Additional wrapping for #3140
8 years ago
4b648793f2
Use ENABLED with DISABLE_[INACTIVE_][XYZ]
8 years ago
f9ded2a7c4
Wrap macros to prevent bad expansions
8 years ago
614febaaf3
Fix acceleration limits
See: https://github.com/Ultimaker/Marlin/pull/7
8 years ago
71718d888a
Fix typos in check_axes_activity
8 years ago
ff13070b59
Use _BV macros, patch up others
8 years ago
209f5f21e0
Use macros where possible
Apply `constrain`, `NOMORE`, `NOLESS` and `CRITICAL_SECTION` macros
wherever possible.
8 years ago
772460a7b8
Various minor spelling corrections
Redo of #2939 rebased against RCBugFix
8 years ago
373e8a1ad4
Fixes for COREXY and COREXZ coordinates
9 years ago
7a670e3911
Improve planner & stepper PR #263
9 years ago
78a347a01a
change nx, ny, nz and ne from float to long
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
9 years ago
6d691aceee
change dx, dy, dz and de from float to long
anything is long, we don't need float there
9 years ago
0fbfb22506
Renaming delta speeds (PR2824)
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
9 years ago
9bdab4f3a8
Clean up "else" and other spacing
9 years ago
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
Keep "astyled" reformatting
9 years ago
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
9 years ago
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
9 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
29b456ae07
Suppress some compiler warnings
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
Apply `ENABLED` / `DISABLED` macros to planner files.
9 years ago
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
9 years ago
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
9 years ago
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
9 years ago
fa00e1d97f
Explode conditions common to corexy and cartesian
9 years ago
54ddc1d417
Simplify DRY RUN (PR#2358)
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
9 years ago
788eb6e647
planner.cpp: remove tab
planner.cpp: single evil and hidden tab removed ♻️ 😏
9 years ago
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
9 years ago
e7e964432b
consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
9 years ago
76306f9073
Insert Debug DRYRUN Repetier Host compatible
9 years ago
d76a01194d
Slight size reduction by adding idle()
9 years ago
513077c317
Minor change to fan kick
9 years ago
35493e1af9
Tweak to planner.cpp position.debug
9 years ago
0fca084ea6
Make EEPROM reproducible in GCode
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.
- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
9 years ago
3f02da646c
Make sure axis_active is cleared for #1908
9 years ago
ccddc280be
Apply three more commits
9 years ago
8857b9e921
Use the extruder argument in plan_buffer_line
9 years ago
Scott Lahteine
jbrazio
AnHardt
Richard Wackerbarth
Wurstnase
Andrew Lenharth
CONSULitAS
MagoKimbra