c3fe6e61ae
Merge pull request #2229 from AnHardt/position-out-of-range
Fix out_of_range_error()
10 years ago
38c21ff34d
Merge pull request #2236 from AnHardt/backto103def
Back to 1.0.3 dev - for now
10 years ago
b7e9ba7591
Back to 1.0.3 dev - for now
10 years ago
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
Versioning
10 years ago
17b0ec84ed
Fix out_of_range_error()
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
10 years ago
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
consistency name for multiplier
10 years ago
e7e964432b
consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
10 years ago
d4c6fc5d0a
Merge pull request #2223 from AnHardt/dualz-semicolon
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
10 years ago
0d9d21d15f
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
10 years ago
ca2dcff9d4
Merge pull request #2219 from MagoKimbra/Cura_bug
Fix problem Width Cura
10 years ago
881146bc22
Fix problem Width Cura
10 years ago
c33fffd6a7
Merge pull request #2209 from AnHardt/u8glib
Replace U8GLI v1.11 with v1.17
10 years ago
01a7b5cc97
Merge pull request #2210 from fmalpartida/bugFixing
Addes support for SDD1306 I2C OLED LCD
10 years ago
cc5d006087
Revert "updated addons for IDE 1.6.4"
This reverts commit 2724baae8b
10 years ago
2724baae8b
updated addons for IDE 1.6.4
10 years ago
11e3f3375d
Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
Updated LCD wiki location.
10 years ago
6f4873329e
Replace U8GLI v1.11 with v1.17
In Travis we already test against 1.17.
10 years ago
764e61708b
Merge pull request #2208 from alexxy/ru_translations
Update ru translation
10 years ago
a8670b66a7
Update ru translation
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
10 years ago
93da52d011
Added support for OLED SSD1306 I2C based LCDs.
10 years ago
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
faster compare
10 years ago
0f3f7d6835
clean up double endstops
10 years ago
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
Slight size reduction by adding idle()
10 years ago
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
Redo "invalid extruder" to save 304 bytes
10 years ago
be5236e839
Reduce setTargetedHotend by removing the switch
10 years ago
06f401e7e5
Redo "invalid extruder" to save 264 bytes
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
10 years ago
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
Ignore unknown commands if they start with G, M, or T
10 years ago
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
Print active extruder with M105 for MAX6675
10 years ago
9beed830eb
Drop commented code_is_good lines
10 years ago
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
10 years ago
5824f613ff
Merge pull request #2185 from jothan/bed_integral
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
10 years ago
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
Initialize the display earlier
10 years ago
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
Replace MSG_F? with MSG_N?
10 years ago
eecabf0b00
Merge pull request #2190 from thinkyhead/new_parser_m33
Update M33 for new gcode parser
10 years ago
0564625757
Update M33 for new gcode parser
10 years ago
f18f689c01
Replace MSG_F? with MSG_N?
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
10 years ago
af7e3f5076
Print active extruder with M105 for MAX6675
Was omitted when T0 is a MAX6675.
10 years ago
d46d9d998e
Add maximum bed integral term in example configurations.
10 years ago
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
10 years ago
a8a8f236d2
Merge pull request #2180 from thinkyhead/fix_radian
Fix DEGREES macro
10 years ago
f0523b5816
Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
10 years ago
790c697c19
Fix DEGREES macro
10 years ago
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
M110 is a known command
10 years ago
03d5709b09
M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
22c8bc5ef4
Merge pull request #2157 from AnHardt/bed-mintemp
Activate BED_MINTEMP error
10 years ago
97a48e36e9
Merge pull request #2156 from AnHardt/kill3
Call kill() only once when triggered by a temperature error
10 years ago
2deb5a8ac5
Temporary Hack
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
AnHardt
wurstnase
MagoKimbra
Bo Herrmannsen
fmalpartida
Alexey Shvetsov
Scott Lahteine
Scott Lahteine
Jonathan Bastien-Filiatrault
Richard Wackerbarth