849dea92a8
Move probe extras below probe types
6 years ago
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
6 years ago
bae8f82ba8
[2.0] Fix Mixing Extruder mixing factors ( #11861 )
6 years ago
f5c210d33d
Config changes supporting up to 6 extruders
6 years ago
1a6f2b29b8
Add support for Triple-Z steppers/endstops
6 years ago
e25d2ae4a2
[2.0.x] SWITCHING_TOOLHEAD ( #11623 )
6 years ago
2a61c9a939
Various fixups to configs, spacing, etc.
6 years ago
3e81745e81
Fix issues, make optional
6 years ago
66966dbd69
Tweak comments for newer multiplexer
6 years ago
6483285bc5
HOTEND_OFFSET_Z always available ( #11603 )
6 years ago
bd6d032628
Update default driver configuration
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
846bd24eb9
MALYAN_LCD is ok without SD
6 years ago
a1a5367380
Smoothieboard V1.0/1.1 and A5984 support
6 years ago
bd3ec66a78
[2.0.x] typo fix ( #11365 )
Typo fix
6 years ago
fbcdf5eaeb
Simplify stepper driver per-axis selection
6 years ago
14e2b11195
Fix spelling in configs
6 years ago
2106fa26b1
Add MANUAL_PROBE_START_Z for manual probing
6 years ago
25e2ca8896
Add Z_CLEARANCE_MULTI_PROBE
Co-Authored-By: nightgryphon <ngryph@gmail.com>
6 years ago
cbea385ed7
[2.0.x] Fix LCD_LANGUAGE options list formatting in config ( #11198 )
* Fix LCD_LANGUAGE options list formatting in config
* Remove 'cn' language option from list
6 years ago
568cfe7caa
Add thermistor 501 (100K Zonestar)
6 years ago
6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
6 years ago
aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
6 years ago
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
6 years ago
b7dfc79988
Disable SERIAL_PORT_2 by default and sanity-check it ( #10748 )
6 years ago
e978e6e782
[2.0.x] Arrange LCD options by type ( #10630 )
6 years ago
e911635fb1
Add thermocouple with AD8495 support
6 years ago
b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
6 years ago
c87b0e21be
Add units to probe speed comments
6 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
6 years ago
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
6 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
6 years ago
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
6 years ago
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
6 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
6 years ago
dca69efc11
Update Bed PID comments
6 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
6 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
6 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
6 years ago
dd2949922b
Consolidate 3-point leveling point options
6 years ago
c6ff39cc14
Spacing cleanup
6 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
6 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
6 years ago
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
6 years ago
a2a672449a
Updated boot screen description
6 years ago
4953fb1c88
Standardize encoder defaults
6 years ago
5684beae90
Bring some configs up to speed
6 years ago
2024775e07
Spanish (UTF8) Language ( #9786 )
From #7314 by @MrAmericanMike
6 years ago
b2cf253a13
Add RESTORE_LEVELING_AFTER_G28 option
6 years ago
716a22498f
Changed temp type from uint8_t to int16_t
- Also deleted old implementation files which had been renamed.
6 years ago
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD ( #9740 )
6 years ago
Scott Lahteine
Hannes Brandstätter-Müller
Scott Lahteine
Holger Müller
Kevin
Greg Nutt
Giuliano
teemuatlut
Chris Pepper
etagle
nightdemonx
KangDroid
Yunhui Fu
Lenbok
Marcio Teixeira