oni303
ab09fa4bbf
fixed pwm generation at pin D12 and D13 when one of them is used as FAN_PIN on Sanguino, added soft pwm entry for FAN_PIN in temperature.cpp
12 years ago
daid303
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
Johann Rocholl
ca409e5531
Fix X/Y/Z_MIN_PIN for Printrboard.
12 years ago
Johann Rocholl
2292441f0c
Use X/Y/Z_MAX_PIN instead of X/Y/Z_MIN_PIN for top endstops on deltabot.
12 years ago
Johann Rocholl
33247733e0
Teensylu and Printrboard use different analog pins for thermistors.
12 years ago
Johann Rocholl
6cba11f087
Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.
12 years ago
Johann Rocholl
4d351b4846
Improved formatting and comments for consistency.
12 years ago
Johann Rocholl
a30007caa4
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
12 years ago
Johann Rocholl
b1c38d4c82
Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.
12 years ago
Johann Rocholl
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
brupje
57429cb9fe
Fix for keypad
12 years ago
daid303
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
Jonathan Bastien-Filiatrault
0f73afb0b0
Avoid defining overriding definitions for the RepRapDiscount Smart
Controller. Remove common definitions. Harmonize declaration order.
12 years ago
Jonathan Bastien-Filiatrault
36b452c7ac
Remove abbrs.
12 years ago
Jonathan Bastien-Filiatrault
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
Bracken Dawson
f5631a89e8
Add dummy Emergancy Pin to Gen7 1.4
Change required after pulling from ErikZalm.
12 years ago
Bracken Dawson
2873d67b17
Put bogus temp override back in Gen7 up to 1.3
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
12 years ago
brupje
d07b6e93d5
Add support for Megatronics
12 years ago
johnnyr
8016f058bc
fix max endstop pins
12 years ago
Erik vd Zalm
abf0693e8e
Added KILL_PIN -1 to gen7 boards
12 years ago
Drakelive
d728e35658
Update Marlin/pins.h
12 years ago
tonokip
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
motor current and microstepping pins.
12 years ago
Bracken Dawson
47d4f55bc0
Fix Gen7 1.4 pinout
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
12 years ago
Enchiridion
50cde90324
Added support for dual Z axis stepper drivers
12 years ago
Chris Palmer
538189cc19
Fixed soft limits when the origin is in the middle.
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
12 years ago
Daid
e9bec9b6fe
Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6)
12 years ago
Guan Yang
602c8ee02b
Melzi support
12 years ago
Bernhard
464b755918
added support for the UltiController
13 years ago
Michel Pollet
5550e893d5
New board variant, Open Motion Controller
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/
Signed-off-by: Michel Pollet <buserror@gmail.com>
13 years ago
Erik van der Zalm
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
13 years ago
Erik van der Zalm
c077316b2b
Added PID autotune. (experimental)
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
13 years ago
Blair Thompson
02ee9e3d30
Changed Pin Assignment for the RAMPS motherboard so that LCD and Rotary encoder are all wired to AUX-4
This simplifies wiring for those with RAMPS 1.3 and 1.4 boards.
13 years ago
Erik van der Zalm
ed951b1977
Fixed RAMPS 1.2 support (Found and fixed by rrhb)
13 years ago
Blair Thompson
f278e1c00f
This is in my opinion a much better way of dealing with SD cards than my previous fix.
Instead of adding a momentary switch to fake the insertion of the card I have modified the ultralcd menu item:
Card Menu -> Refresh
to reinitialise the card providing that the SDCARDDETECT pin has been set to -1 in the pins.h file. This requires one less switch on the front panel and the refresh menu item is in the most relevent place for a user who wishes to inert a card and then print from it.
It also means that the "Card inserted" messages do not bother the users of these card readers (they dont make sense for users without SCCARDDETECT)
13 years ago
Daid
00d33e6b82
Typo fix
13 years ago
Daid
7d124478fa
Only protect the heater pins for the defined extruders.
Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
13 years ago
Phil Hord
b65ef8d66c
Add support for upcoming Gen7 v1.4
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
13 years ago
Phil Hord
740f0c7690
Add explicit #define for bogus temp override
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature. But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
13 years ago
Phil Hord
ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
13 years ago
Changwoo Ryu
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
13 years ago
Daid
286d5003fa
Fixed compiler warning for Sanguino compile
13 years ago
Erik van der Zalm
ce714fe306
Fixes in pins.h
13 years ago
Erik van der Zalm
35e57bf149
Added gen6 deluxe.
13 years ago
Erik van der Zalm
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
Blair Thompson
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
13 years ago
Blair Thompson
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
13 years ago
Christian Thalhammer
e661578c84
support for GEN7 1.1,1.2 and 1.3
13 years ago
Erik van der Zalm
da040fd393
Fixed ultimaker heater 1 pins. (Thanks daid)
13 years ago
Christian Thalhammer
a11f3b2d2f
- Pins for modified GEN7 assigned
- Added support for ATMega1284
13 years ago
Erik van der Zalm
9f139d6e0e
Added MAX6675 support. (Thanks to gregfrost)
Needs some work to remove the blocking in read max6675.
13 years ago