Browse Source

Add support for Printrboard (from https://github.com/lincomatic/Marlin) and Brainwave (from https://github.com/metrix/Sprinter).

pull/1/head
Johann Rocholl 12 years ago
parent
commit
42e21bb06e
  1. 2
      Marlin/Configuration.h
  2. 200
      Marlin/pins.h

2
Marlin/Configuration.h

@ -37,6 +37,8 @@
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
// 8 = Teensylu
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 9 = Gen3+
// 70 = Megatronics
// 90 = Alpha OMCA board

200
Marlin/pins.h

@ -1015,6 +1015,206 @@
#endif
#endif
/****************************************************************************************
* Printrboard Rev. B pin assingments (ATMEGA90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in arduino IDE!
http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
****************************************************************************************/
#if MOTHERBOARD == 81
#define MOTHERBOARD 8 // Disable MarlinSerial etc.
#define KNOWN_BOARD 1
#ifndef __AVR_AT90USB1286__
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 28
#define X_DIR_PIN 29
#define X_ENABLE_PIN 19
#define X_MIN_PIN 47
#define X_MAX_PIN -1
#define Y_STEP_PIN 30
#define Y_DIR_PIN 31
#define Y_ENABLE_PIN 18
#define Y_MIN_PIN 20
#define Y_MAX_PIN -1
#define Z_STEP_PIN 32
#define Z_DIR_PIN 33
#define Z_ENABLE_PIN 17
#define Z_MIN_PIN 36
#define Z_MAX_PIN -1
#define E0_STEP_PIN 34
#define E0_DIR_PIN 35
#define E0_ENABLE_PIN 13
#define HEATER_0_PIN 15 // Extruder
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 14 // Bed
#define FAN_PIN 16 // Fan
#define TEMP_0_PIN 1 // Extruder - ANALOG PIN NUMBERING
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 0 // Bed - ANALOG PIN NUMBERING
#define SDPOWER -1
#define SDSS 26
#define LED_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
#define SCK_PIN 21
#define MISO_PIN 22
#define MOSI_PIN 23
#endif
#ifdef ULTRA_LCD
#ifdef NEWPANEL
//arduino pin which triggers an piezzo beeper
#define BEEPER 33 // Beeper on AUX-4
#ifndef MCP28017_LCD
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
#endif // MCP28017_LCD
//buttons are directly attached using AUX-2
#define BTN_EN1 11 // PC1
#define BTN_EN2 12 // PC2
#ifndef VERSAPANEL
#define BTN_ENC 31 //the click
#endif
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT -1 // Ramps does not use this port
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
#else //old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 33 No Beeper added
//buttons are attached to a shift register
// Not wired this yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
#endif
#endif //ULTRA_LCD
#endif
/****************************************************************************************
* Brainwave 1.0 pin assignments (AT90USB646)
* Requires hardware bundle for Arduino:
https://github.com/unrepentantgeek/brainwave-arduino
****************************************************************************************/
#if MOTHERBOARD == 82
#define MOTHERBOARD 8 // Disable MarlinSerial etc.
#define KNOWN_BOARD 1
#ifndef __AVR_AT90USB646__
#error Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 27
#define X_DIR_PIN 29
#define X_ENABLE_PIN 28
#define X_MIN_PIN 7
#define X_MAX_PIN -1
#define X_ATT_PIN 26
#define Y_STEP_PIN 31
#define Y_DIR_PIN 33
#define Y_ENABLE_PIN 32
#define Y_MIN_PIN 6
#define Y_MAX_PIN -1
#define Y_ATT_PIN 30
#define Z_STEP_PIN 17
#define Z_DIR_PIN 19
#define Z_ENABLE_PIN 18
#define Z_MIN_PIN 5
#define Z_MAX_PIN -1
#define Z_ATT_PIN 16
#define E0_STEP_PIN 21
#define E0_DIR_PIN 23
#define E0_ENABLE_PIN 22
#define E0_ATT_PIN 20
#define HEATER_0_PIN 4 // Extruder
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 38 // Bed
#define FAN_PIN 3 // Fan
#define TEMP_0_PIN 7 // Extruder / Analog pin numbering
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 6 // Bed / Analog pin numbering
#define SDPOWER -1
#define SDSS -1
#define LED_PIN 39
#define PS_ON_PIN -1
#define KILL_PIN -1
#define ALARM_PIN -1
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
#define SCK_PIN 21
#define MISO_PIN 22
#define MOSI_PIN 23
#endif
#endif
/****************************************************************************************
* Gen3+ pin assignment
*

Loading…
Cancel
Save