fccc97de6d
Save PROGMEM with string changes
Unlike RAM-based strings, PROGMEM strings aren’t consolidated by the
compiler.
8 years ago
27dd5acc22
Fix set_led_color for BLINKM
Follow-up to #5330
8 years ago
f60b4f8659
Allow case light pin to be active low
8 years ago
65c50e062e
Support for an RGB LED using 3 pins
8 years ago
61437d988a
Fix and optimize case-light code
8 years ago
f6f77d34a1
Add a fade factor for mesh leveling
8 years ago
2e966f8e5b
Patch Capabilities Report for "PROGRESS"
8 years ago
0c341f0c50
Added Menu entry for Case light
8 years ago
3bc2273ac9
Comment M540
8 years ago
3e0376b45e
Reorder M114 and M119 gcode cases
8 years ago
127e21ae00
Extend M122 for all steppers
8 years ago
d67c1d825f
Add TMC2130 support
8 years ago
11effeee2c
Add an option for delta to home to the top
8 years ago
29b174bfb9
Fix z feedrate value when doing mesh bed leveling. probe feedrate uses XY_PROBE_SPEED
8 years ago
87b6b19256
Patch CASE_LIGHT typo
8 years ago
181cdb3cfe
Move GCode list above include lines
8 years ago
eb120e518c
Followup to new endstop interrupts feature
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
8 years ago
98600e1433
Minor stepper cleanup
8 years ago
d08867986e
Add autotemp capabilities to M104
This allows M104 to pass the F and B parameters to enable autotemp as well
8 years ago
d7ce5d271b
Replace const bool with #define for consistency
8 years ago
99b0c1fe56
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
8 years ago
410657b050
Fix G30 with limits, print correct probe XY
8 years ago
f3eee02596
Introduce endstop interrupts
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.
The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.
This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
8 years ago
f663220e87
Store Mix factors as reciprocals and multiply
8 years ago
b31a07e261
Stateful M355 with separate P parameter
8 years ago
3c9a838651
Extended capabilities report in M115
8 years ago
68b866b5dd
Add M155 - Auto-report temperature with interval
8 years ago
75bfde9945
M155=>M260, M156=>M261
8 years ago
e765eebfb0
Patch spacing in bilinear grid report
8 years ago
1864b282c5
Implement reversed CORE options
8 years ago
dea00bbcf1
improve G30 probing
Add optional parameters
X, Y for probe point
S sets stowing on and off
8 years ago
176aeafc19
Don't define bilinear_line_to_destination on kinematic setups
8 years ago
236853df22
Corrections to bilinear_line_to_destination
- Allow more than 9x9 probe points
- Account for the probe starting position
8 years ago
0115e495fe
Fix up Dual X switch blocks
8 years ago
2495ab7af2
Make dual_x_carriage_mode an enumeration
8 years ago
d6c36f5bb9
Fix Z raise with DXC_AUTO_PARK_MODE
8 years ago
0c79553fc5
Cast int to AxisEnum for some accessors
8 years ago
adbf1f7dca
Add M355 to the GCodes list.
8 years ago
ee5b8d6dc8
Split moves on grid boundaries with bilinear ABL on cartesian
8 years ago
955d14acb0
Patch photo pin code style
8 years ago
ab3f966f5f
Case light G-code M355
implemented G-Code M355 into Marlin
8 years ago
f9bea7968f
BugFix for incorrect E-speed calculation
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
8 years ago
ff3a8ca0d1
Use NUM_DIGITAL_PINS instead of custom DIO_COUNT
8 years ago
04a1fac029
Some cleanup to M43
8 years ago
c7f1f0dae6
Add endstop monitor & make pins report pretty
8 years ago
396434a445
Fix compiler warning in M145
8 years ago
07bfc45df8
Adjust spacing in gcode_M149
8 years ago
1a2310c494
Make LCD preheat vars an array to reduce code size
8 years ago
50ee749082
Centralize click-handling in the LCD loop
8 years ago
67ab54185b
Save hotend_offset array (M218) in EEPROM
8 years ago
Scott Lahteine
Scott Lahteine
Kai
Moritz
Moshen Chan
Florian Heilmann
Petr Zahradník junior
AnHardt
Nikolay Zinov
Stanley
Sebastianv650
Bob-the-Kuhn