7231a20dba
Put #ifdef around servo pins in pins.h. This allows the pins to be used for M42.
12 years ago
424101110c
Add Panelolu2 support for Melzi
12 years ago
dc59f07d24
First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple.
12 years ago
9cc15876be
Add support for RUMBA thermocouple add on
12 years ago
bd2cd4903e
Added #ifdef BARICUDA around the BariCUDA changes
12 years ago
fbd899a37d
Support for BariCUDA Paste Extruder derived from MakerBot Frostruder. Using Ultimachine RAMBo board. M126/M127 and M128/M129.
12 years ago
2739c26c4f
changes:
- changed the variables from keypad to reprapworld_keypad
- added a missing ifdef check
12 years ago
6fb9573157
added support for the reprapworld keypad
12 years ago
d5ee2a5a62
Make Gen7 1.4 heater pins match silkscreen
12 years ago
0d075378d5
Add LARGE_FLASH define and enable it for some of the beefier boards
The LARGE_FLASH flag allows superfluous features to be excluded
on boards with less memory
12 years ago
91bea43332
Added rumba pinout
12 years ago
9a78f321a4
Add pins for Motherboard variant 64
These definition contain also the definition for the graphics LCD.
12 years ago
140e095c6e
Add pins for Motherboard variant 64
These definition contain also the definition for the graphics LCD.
12 years ago
1292d735ba
Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575)
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
12 years ago
12c41423ad
Fixed typo in comment
12 years ago
0995eaa492
Chenged LED_PIN for Melzi boards, added comment about broken versions of the Sanguino libraries
12 years ago
408b349a84
Fixed #368 . Commented out the wrong pin definition, but explained why it is there.
12 years ago
86358dd6cd
Panelolu pin assignment for sanguinololu from http://reprap.org/wiki/Panelolu
12 years ago
bbe7d3d0fe
Fixed #312
12 years ago
8caf5d252d
Remove bogus blank line.
12 years ago
b39f5d614a
For boards with only one endstop per axis, automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
12 years ago
ab09fa4bbf
fixed pwm generation at pin D12 and D13 when one of them is used as FAN_PIN on Sanguino, added soft pwm entry for FAN_PIN in temperature.cpp
12 years ago
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
ca409e5531
Fix X/Y/Z_MIN_PIN for Printrboard.
12 years ago
33247733e0
Teensylu and Printrboard use different analog pins for thermistors.
12 years ago
6cba11f087
Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.
12 years ago
4d351b4846
Improved formatting and comments for consistency.
12 years ago
a30007caa4
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
12 years ago
b1c38d4c82
Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.
12 years ago
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
57429cb9fe
Fix for keypad
12 years ago
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
0f73afb0b0
Avoid defining overriding definitions for the RepRapDiscount Smart
Controller. Remove common definitions. Harmonize declaration order.
12 years ago
36b452c7ac
Remove abbrs.
12 years ago
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
f5631a89e8
Add dummy Emergancy Pin to Gen7 1.4
Change required after pulling from ErikZalm.
12 years ago
2873d67b17
Put bogus temp override back in Gen7 up to 1.3
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
12 years ago
d07b6e93d5
Add support for Megatronics
12 years ago
8016f058bc
fix max endstop pins
12 years ago
abf0693e8e
Added KILL_PIN -1 to gen7 boards
12 years ago
d728e35658
Update Marlin/pins.h
12 years ago
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
motor current and microstepping pins.
12 years ago
47d4f55bc0
Fix Gen7 1.4 pinout
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
12 years ago
50cde90324
Added support for dual Z axis stepper drivers
12 years ago
538189cc19
Fixed soft limits when the origin is in the middle.
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
13 years ago
e9bec9b6fe
Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6)
13 years ago
602c8ee02b
Melzi support
13 years ago
464b755918
added support for the UltiController
13 years ago
5550e893d5
New board variant, Open Motion Controller
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/
Signed-off-by: Michel Pollet <buserror@gmail.com>
13 years ago
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
13 years ago
Erik van der Zalm
Bas Spaans
Gord Christmas
MaikStohn
Jordan Miller
gregor
Bracken Dawson
Colin Edwards
blddk
Dirk Eichel
Robert F-C
daid303
Yuri Valentini
Johann Rocholl
oni303
brupje
Jonathan Bastien-Filiatrault
johnnyr
Drakelive
tonokip
Enchiridion
Chris Palmer
Guan Yang
Bernhard
Michel Pollet