1e9cf905c7
Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
ZigZag has been disabled by fault due to do_topography_map
10 years ago
6ab7b560af
Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
10 years ago
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
10 years ago
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
10 years ago
eb81982fcd
Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
10 years ago
55b23c896a
Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
10 years ago
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
10 years ago
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
10 years ago
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
10 years ago
96a3fba8ac
Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
10 years ago
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
10 years ago
ad09d6a60f
3 Step Allen Key Probe
10 years ago
17b0ec84ed
Fix out_of_range_error()
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
10 years ago
e7e964432b
consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
10 years ago
76306f9073
Insert Debug DRYRUN Repetier Host compatible
10 years ago
881146bc22
Fix problem Width Cura
10 years ago
be5236e839
Reduce setTargetedHotend by removing the switch
10 years ago
06f401e7e5
Redo "invalid extruder" to save 264 bytes
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
10 years ago
9beed830eb
Drop commented code_is_good lines
10 years ago
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
10 years ago
0564625757
Update M33 for new gcode parser
10 years ago
af7e3f5076
Print active extruder with M105 for MAX6675
Was omitted when T0 is a MAX6675.
10 years ago
f0523b5816
Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
10 years ago
03d5709b09
M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
68f6f149d0
Reduce code size with out_of_range_error function
- Affects code size when automatic bed leveling is enabled
10 years ago
b55f8718c3
Indent G90/G91, G92
10 years ago
b0d520b109
Indent G30, G31/G32
10 years ago
ffe27a6225
Indent G29
10 years ago
86083badc2
Indent G4, G10/G11, G28
10 years ago
47d7a9cb5e
Indent G2/G3
10 years ago
350f239d84
Indent G0/G1
10 years ago
15a2351675
No need for +1 on initial seen_pointer
10 years ago
550dd87b2a
Set seen_pointer before calling code_value
10 years ago
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
10 years ago
bde9c70d42
Suppress the line mismatch error after M303
10 years ago
735bf2d35f
Describe Custom M Code
10 years ago
f39658c822
M120 and M121 are reversed
10 years ago
89d2ee6f13
Make output on display dependant of ULTRA_LCD
10 years ago
f4a93ed997
Add a string parameter to kill()
Makes the output on the LCD adjustable.
10 years ago
a0f362c735
Simplify & optimize with current_command_args
10 years ago
adc8fcb77f
More parser comments, optimize code_seen, save with goto
10 years ago
c6d8dd19d9
use fetched value
10 years ago
1116e13f5a
Further optimization of command parser
10 years ago
3a4c3ab76e
Pre-sanitize the command before handling
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
10 years ago
0f2c9bacfd
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
3feaef6526
Have G92 set the nozzle position on Delta and SCARA
10 years ago
d580a0d186
Use "+=" in plane rotation
10 years ago
2f3a410cb0
Fix a potential hanging "else" bug
10 years ago
schlotzz
AnHardt
Scott Lahteine
Scott Lahteine
MagoKimbra
paclema
Richard Wackerbarth
wurstnase