22d7fed60a
Fix compile error with SD_FIRMWARE_UPDATE ( #12462 )
6 years ago
779b2709ec
Change temperature pin order for RemRam V1 ( #12458 )
Beta testers suggested to adopt the RAMPS order of temperature probe connectors. This commit fixes the order to the RAMPS order.
6 years ago
8ebb4dc294
Followup to static CardReader
6 years ago
7ee5894360
Allow float XY probe offsets
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
6 years ago
43ecdb606f
Fix a compile warning ( #12452 )
6 years ago
984c4ba8c7
Enable SD Card on RepRap Display and RADDS ( #12446 )
* Enable SD Card on RepRap Display and RADDS
Define the necessary pins in `pins_RADDS.h` (copied from the `RADDS_DISPLAY` section) for the use of the SD card slot on RRD.
6 years ago
56a94c2a26
Use 'target_extruder' in M104 as with M109 ( #12448 )
6 years ago
66580f32c2
Make CardReader class static ( #12451 )
* Make CardReader a static class
* Make CardReader flags into bitfields
6 years ago
3e9ffaddb6
Consolidate, optimize some LCD menu code ( #12450 )
6 years ago
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
6 years ago
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
6 years ago
0e610815e4
No need for Cap:PAREN_COMMENTS
6 years ago
7a075a5dc9
Tweak extruder errors
6 years ago
2d92f333f5
Fix GcodeSuite::T active_extruder reference
6 years ago
d2bb53702a
Optimize target_extruder, ignore T with mixing ( #12432 )
* Optimize target_extruder, ignore T with mixing
* Give G-code Tn parity with tool_change
6 years ago
5e586a6b39
Fix to runout sensor code. ( #12431 )
- "old_state" is no longer a class static variable.
6 years ago
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
6 years ago
edfd106bc5
Rejigger Filament Runout class ( #12428 )
6 years ago
f4c128ecaa
Move RRW keypad code to a common method ( #12429 )
6 years ago
54ec5528a0
hasstatus => has_status
6 years ago
ebf585b673
Fix an old sanity check
6 years ago
052d102ded
UltiMachine Archim 1 support ( #12404 )
6 years ago
664e20754d
Clean up pins files
6 years ago
1eb5249598
Fix Formbot Trex-2+ configs
Followup to #12422
6 years ago
075a22ed65
Update Portuguese-Brazilian translation ( #12402 )
6 years ago
3ceab8474c
Add required "cardreader.h" include ( #12419 )
6 years ago
98c2fc4e42
Endstops fix followup ( #12423 )
Followup to #12413
6 years ago
f19fd642ce
Updates to Formbot T-Rex 2+ configuration files ( #12422 )
Updates to Formbot T-Rex 2+ configuration files
6 years ago
cda5ef08fa
Debug of G2-G3 for UBL ( #12386 )
Changes only affect UBL. Everything else is left alone.
6 years ago
9ad3aed0ef
Fix tool-change for MIXING_EXTRUDER with < 2 virtual tools ( #12417 )
Fix #12416
Better handling of `ENABLED(MIXING_EXTRUDER) && !MIXING_VIRTUAL_TOOLS > 1` - to not fall through to the general case. Fix compiler warnings for `#elif EXTRUDERS < 2`.
6 years ago
d631267548
Refine endstops fixes ( #12413 )
When endstops/probe are enabled `ENDSTOP_NOISE_THRESHOLD` calls to `update` are required to properly re-sync endstops/probe status.
6 years ago
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
6 years ago
690c4e8457
Clean TLM trailing whitespace
6 years ago
143b2896e0
Add M412 to enable/disable filament runout detection ( #12406 )
6 years ago
a163c89c6a
Followup to 50af1d1
6 years ago
fea2363a2e
Clear old _site contents on regeneration
6 years ago
be6271767f
Fix BABYSTEP_ZPROBE_OFFSET ( #12408 )
Fix #12399
Did not compile without `WATCH_HOTENDS || WATCH_THE_BED`.
Add condition to include "../../module/temperature.h".
6 years ago
50af1d1e08
Differentiate translated On/Off from Serial ON/OFF
6 years ago
df907a905f
Update UBL comments for debug change
6 years ago
da17f8ad37
For now (!) don't synchronize in M204 and M205
See if this has any deleterious effect on motion planning by slicers that inser their own jerk and acceleration controls. The problem I see is that these settings can take effect on blocks already in the planner, and the only way around this would be to shadow these settings in planner blocks and use the shadowed settings in the planner.
6 years ago
a3923424c7
Clean up LCD width/height determination
6 years ago
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
6 years ago
9da6809ac3
Adjust some comment spacing
6 years ago
471f403a67
Reduce code size with plain inlines
6 years ago
30a49f5ee2
Apply extra condition to LCD_PROGRESS_BAR
6 years ago
4e0c935959
Update HAL and libs formatting
6 years ago
47483e8c17
Update Raptor config
6 years ago
6093df11dc
Allow G26 to use the active extruder ( #12387 )
* Make lcd_quick_feedback argument optional
* Add click_to_cancel option to wait_for_hotend/bed
* Have G26 use the active nozzle and wait_for_hotend/bed
* Use wait_for_release in UBL G29
* Add 'T' parameter to G26 for an initial tool-change
6 years ago
4260282df7
Tevo Little Monster example configuration ( #12370 )
6 years ago
bed15fcd81
Tweak 'echo_not_entered' used by MBL's G29
6 years ago
Ludy
Nils Hasenbanck
Scott Lahteine
Giuliano Zaro
Ph0non
Scott Lahteine
Mateusz Krawczuk
Marcio Teixeira
Ryan
thiagodesacosta
Roxy-3D
AnHardt
articide