fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
9 years ago
8b876241bd
Some more servo code tweaks
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
9 years ago
90f8ddfc1e
Apply MINIPANEL to other configs
9 years ago
00dbf69b6d
add MINIPANEL defines
9 years ago
d85861d296
Move macros, add ENABLED/DISABLED, add includes
9 years ago
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
9 years ago
129f986ccf
Add COREXZ option to configurations
10 years ago
de25a48dec
Remove PID examples from preconfigured configs
9 years ago
7456710a1f
Update configs formatting
9 years ago
391386dd94
Update configs for new servo deactivation
9 years ago
a0351bdb73
Remove STEPPER_RESET_FIX option
9 years ago
8e61314323
Use RIGIDBOT_PANEL for consistency with online docs
9 years ago
536f86e896
RigidBot CONTROLLERFAN_PIN in Configuration_adv.h
9 years ago
9ebcae496d
RIGIDBOARD / RIGIDPANEL
9 years ago
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
9 years ago
dc40a5f6e0
Patch up more outdated config lines
10 years ago
98c9111a7d
Update delta configs with latest settings
10 years ago
e6baf8afd9
Fix up allen key settings in delta configs
10 years ago
3b293fc5d1
Move Delta settings lower in delta files
10 years ago
df21857583
Move extruder offset settings next to extruders setting
10 years ago
2dd1859247
Cleanup spaces and comments in configs and conditionals
10 years ago
a274769f4f
Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
10 years ago
d3bce05d54
Fix up spacing for filament sensor values
10 years ago
b4b10a57fe
Fix configurator section directives and values lists
10 years ago
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
10 years ago
c85a486445
make the dual z-endstop optional (PR#2277)
it's disabled by default
10 years ago
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
10 years ago
3a5963c0e7
Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
10 years ago
303d47228e
Define Probe Path in new format
10 years ago
08968c29bb
Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples
10 years ago
d46d9d998e
Add maximum bed integral term in example configurations.
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
b878bc5620
Introducing the Kossel Pro Build Configuration
10 years ago
9d1961ebe3
Witbox and Hephestos are just RAMPS_13_EFB
10 years ago
082ed3beed
Propagate Configuration.h changes
Updated all the example Configuration.h files for the new display type.
10 years ago
258bcdefe0
move dogm font selection to configuration_adv.h
10 years ago
7750180c93
transpire -> expire
Minor wording correction.
10 years ago
0f2c9bacfd
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
76438195f0
NO_TIMEOUTS and ADVANCED_OK off by default
10 years ago
78beef2d73
Use Mendel default for INVERT_Y_DIR
10 years ago
d693e0f378
Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit
10 years ago
b2bd9aae7c
SCARA_SEGMENTS_PER_SECOND
10 years ago
429c6ccad2
Neaten config formatting
10 years ago
526ad82d20
activate advanced_ok and no_timeout
10 years ago
2445ae3d3a
Combine thermal runaway and watch-period
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
10 years ago
79106638a8
Fix documentation of heating sanity check
10 years ago
6110494a56
Change default to 4°C in 16s
10 years ago
54deb9eea3
Enable WATCH_TEMP_PERIOD by default
10 years ago
deedb00c18
Document WATCH_TEMP_PERIOD
10 years ago
AnHardt
Scott Lahteine
AndySze
Richard Wackerbarth
wurstnase
CONSULitAS
Ed Boston
Jonathan Bastien-Filiatrault
Christian Bohn