e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
10 years ago
a8a8f236d2
Merge pull request #2180 from thinkyhead/fix_radian
Fix DEGREES macro
10 years ago
f0523b5816
Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
10 years ago
790c697c19
Fix DEGREES macro
10 years ago
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
M110 is a known command
10 years ago
03d5709b09
M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
22c8bc5ef4
Merge pull request #2157 from AnHardt/bed-mintemp
Activate BED_MINTEMP error
10 years ago
97a48e36e9
Merge pull request #2156 from AnHardt/kill3
Call kill() only once when triggered by a temperature error
10 years ago
2deb5a8ac5
Temporary Hack
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
da246f5cb1
Activate BED_MINTEMP error.
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
10 years ago
959da98d8e
Call kill() only once when triggered by a temperature error
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
10 years ago
ffc39dc182
Merge pull request #2153 from thinkyhead/leveling_shrink
Reduce code size with out_of_range_error function
10 years ago
68f6f149d0
Reduce code size with out_of_range_error function
- Affects code size when automatic bed leveling is enabled
10 years ago
f8aabd670e
Notes about Development in its README.md
10 years ago
94120740d8
faster compare
!(~(ab)&0x3) and ab == 0x3 are equal
10 years ago
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
Indentation in process_commands
10 years ago
3778362f88
Merge pull request #2143 from thinkyhead/fix_command_parser_M110
Cleanup pins in RAMPS_13_EFB boards
10 years ago
b55f8718c3
Indent G90/G91, G92
10 years ago
b0d520b109
Indent G30, G31/G32
10 years ago
ffe27a6225
Indent G29
10 years ago
86083badc2
Indent G4, G10/G11, G28
10 years ago
47d7a9cb5e
Indent G2/G3
10 years ago
350f239d84
Indent G0/G1
10 years ago
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
10 years ago
f4584c51c5
Merge pull request #2142 from thinkyhead/fix_command_parser_M110
No need for +1 on initial seen_pointer
10 years ago
15a2351675
No need for +1 on initial seen_pointer
10 years ago
8cba3bd811
Merge pull request #2141 from thinkyhead/fix_command_parser_M110
Set seen_pointer before calling code_value
10 years ago
550dd87b2a
Set seen_pointer before calling code_value
10 years ago
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
Introduction of Bulgarian - language_bg.h
10 years ago
04a1622172
Merge pull request #2127 from Wackerbarth/Kossel_Pro
Kossel Pro
10 years ago
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
Witbox and Hephestos are RAMPS EFB
10 years ago
f919a2fed1
Merge pull request #2134 from AnHardt/preheat-all
Shift call of start_watching_heater() into setTargetHotend()
10 years ago
65343e8ae8
Merge pull request #2138 from thinkyhead/tweak_swh
Fix a couple of doubled semicolons
10 years ago
063881b5bd
Fix a couple of doubled semicolons
10 years ago
94dff5b36a
Merge pull request #2137 from thinkyhead/tweak_swh
Move millis call in start_watching_heater
10 years ago
70d2f48d4e
Merge pull request #2136 from thinkyhead/M303_suppress_error
Suppress the line mismatch error after M303
10 years ago
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
10 years ago
00716d0ca0
Small start_watching_heater adjustment
10 years ago
834747deb7
Merge pull request #2135 from Wurstnase/new_endstop_bits
new endstop bits
10 years ago
bde9c70d42
Suppress the line mismatch error after M303
10 years ago
50bd7493cc
Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
4d11b29959
Merge pull request #2113 from thinkyhead/command_sanitizer
Command sanitizer
10 years ago
71ff9adb12
Merge pull request #2132 from thinkyhead/fix_M120_M121
M120 and M121 are reversed
10 years ago
ff98b8632b
new endstop bits
10 years ago
9b0fa9c309
Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS
10 years ago
bc0764894a
Shift call of start_watching_heater() into setTargetHotend()
to warrant watching is set or reset.
Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED.
Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.
10 years ago
b878bc5620
Introducing the Kossel Pro Build Configuration
10 years ago
Jonathan Bastien-Filiatrault
AnHardt
Scott Lahteine
Scott Lahteine
Richard Wackerbarth
wurstnase