Configurable Z move distance (#14593)

Marlin/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

Marlin/src/lcd/language/language_an.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mover Y")
 #define MSG_MOVE_Z                          _UxGT("Mover Z")
 #define MSG_MOVE_E                          _UxGT("Extrusor")
-#define MSG_MOVE_0025MM                     _UxGT("Mover 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mover %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mover 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mover 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mover 10mm")

Marlin/src/lcd/language/language_bg.h

@@ -62,7 +62,7 @@
 #define MSG_MOVE_Y                          _UxGT("Движение по Y")
 #define MSG_MOVE_Z                          _UxGT("Движение по Z")
 #define MSG_MOVE_E                          _UxGT("Екструдер")
-#define MSG_MOVE_0025MM                     _UxGT("Премести с 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Премести с %smm")
 #define MSG_MOVE_01MM                       _UxGT("Премести с 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Премести с 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Премести с 10mm")

Marlin/src/lcd/language/language_ca.h

@@ -76,7 +76,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mou Y")
 #define MSG_MOVE_Z                          _UxGT("Mou Z")
 #define MSG_MOVE_E                          _UxGT("Extrusor")
-#define MSG_MOVE_0025MM                     _UxGT("Mou 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mou %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mou 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mou 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mou 10mm")

Marlin/src/lcd/language/language_cz.h

@@ -202,7 +202,7 @@
 #define MSG_MOVE_Z                          _UxGT("Posunout Z")
 #define MSG_MOVE_E                          _UxGT("Extrudér")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Hotend je studený")
-#define MSG_MOVE_0025MM                     _UxGT("Posunout o 0,025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Posunout o %smm")
 #define MSG_MOVE_01MM                       _UxGT("Posunout o 0,1mm")
 #define MSG_MOVE_1MM                        _UxGT("Posunout o 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Posunout o 10mm")

Marlin/src/lcd/language/language_da.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Flyt Y")
 #define MSG_MOVE_Z                          _UxGT("Flyt Z")
 #define MSG_MOVE_E                          _UxGT("Extruder")
-#define MSG_MOVE_0025MM                     _UxGT("Flyt 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Flyt %smm")
 #define MSG_MOVE_01MM                       _UxGT("Flyt 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Flyt 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Flyt 10mm")

Marlin/src/lcd/language/language_de.h

@@ -199,7 +199,7 @@
 #define MSG_MOVE_Z                          _UxGT("Bewege Z")
 #define MSG_MOVE_E                          _UxGT("Bewege Extruder")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Hotend zu kalt")
-#define MSG_MOVE_0025MM                     _UxGT(" 0,025 mm")
+#define MSG_MOVE_Z_DIST                     _UxGT(" %s mm")
 #define MSG_MOVE_01MM                       _UxGT(" 0,1   mm")
 #define MSG_MOVE_1MM                        _UxGT(" 1,0   mm")
 #define MSG_MOVE_10MM                       _UxGT("10,0   mm")

Marlin/src/lcd/language/language_el-gr.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Μετακίνηση Y")
 #define MSG_MOVE_Z                          _UxGT("Μετακίνηση Z")
 #define MSG_MOVE_E                          _UxGT("Εξωθητήρας")
-#define MSG_MOVE_0025MM                     _UxGT("Μετακίνηση 0,025 μμ")
+#define MSG_MOVE_Z_DIST                     _UxGT("Μετακίνηση %s μμ")
 #define MSG_MOVE_01MM                       _UxGT("Μετακίνηση 0,1 μμ")
 #define MSG_MOVE_1MM                        _UxGT("Μετακίνηση 1 μμ")
 #define MSG_MOVE_10MM                       _UxGT("Μετακίνηση 10 μμ")

Marlin/src/lcd/language/language_el.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Μετακίνηση Y")
 #define MSG_MOVE_Z                          _UxGT("Μετακίνηση Z")
 #define MSG_MOVE_E                          _UxGT("Εξωθητήρας")
-#define MSG_MOVE_0025MM                     _UxGT("Μετακίνηση 0,025 μμ")
+#define MSG_MOVE_Z_DIST                     _UxGT("Μετακίνηση %s μμ")
 #define MSG_MOVE_01MM                       _UxGT("Μετακίνηση 0,1 μμ")
 #define MSG_MOVE_1MM                        _UxGT("Μετακίνηση 1 μμ")
 #define MSG_MOVE_10MM                       _UxGT("Μετακίνηση 10 μμ")

Marlin/src/lcd/language/language_en.h

@@ -543,8 +543,8 @@
 #ifndef MSG_HOTEND_TOO_COLD
   #define MSG_HOTEND_TOO_COLD                 _UxGT("Hotend too cold")
 #endif
-#ifndef MSG_MOVE_0025MM
+#ifndef MSG_MOVE_Z_DIST
-  #define MSG_MOVE_0025MM                     _UxGT("Move 0.025mm")
+  #define MSG_MOVE_Z_DIST                     _UxGT("Move %smm")
 #endif
 #ifndef MSG_MOVE_01MM
   #define MSG_MOVE_01MM                       _UxGT("Move 0.1mm")

Marlin/src/lcd/language/language_es.h

@@ -80,7 +80,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mover Y")
 #define MSG_MOVE_Z                          _UxGT("Mover Z")
 #define MSG_MOVE_E                          _UxGT("Extrusor")
-#define MSG_MOVE_0025MM                     _UxGT("Mover 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mover %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mover 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mover 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mover 10mm")

Marlin/src/lcd/language/language_eu.h

@@ -166,7 +166,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mugitu Y")
 #define MSG_MOVE_Z                          _UxGT("Mugitu Z")
 #define MSG_MOVE_E                          _UxGT("Estrusorea")
-#define MSG_MOVE_0025MM                     _UxGT("Mugitu 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mugitu %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mugitu 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mugitu 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mugitu 10mm")

Marlin/src/lcd/language/language_fi.h

@@ -65,7 +65,7 @@
 #define MSG_MOVE_Y                          _UxGT("Liikuta Y")
 #define MSG_MOVE_Z                          _UxGT("Liikuta Z")
 #define MSG_MOVE_E                          _UxGT("Extruder")
-#define MSG_MOVE_0025MM                     _UxGT("Liikuta 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Liikuta %smm")
 #define MSG_MOVE_01MM                       _UxGT("Liikuta 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Liikuta 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Liikuta 10mm")

Marlin/src/lcd/language/language_fr.h

@@ -195,7 +195,7 @@
 #define MSG_MOVE_Z                          _UxGT("Déplacer Z")
 #define MSG_MOVE_E                          _UxGT("Extrudeur")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Buse trop froide")
-#define MSG_MOVE_0025MM                     _UxGT("Déplacer 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Déplacer %smm")
 #define MSG_MOVE_01MM                       _UxGT("Déplacer 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Déplacer 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Déplacer 10mm")

Marlin/src/lcd/language/language_gl.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mover Y")
 #define MSG_MOVE_Z                          _UxGT("Mover Z")
 #define MSG_MOVE_E                          _UxGT("Extrusor")
-#define MSG_MOVE_0025MM                     _UxGT("Mover 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mover %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mover 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mover 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mover 10mm")

Marlin/src/lcd/language/language_hr.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Miči Y")
 #define MSG_MOVE_Z                          _UxGT("Miči Z")
 #define MSG_MOVE_E                          _UxGT("Extruder")
-#define MSG_MOVE_0025MM                     _UxGT("Miči 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Miči %smm")
 #define MSG_MOVE_01MM                       _UxGT("Miči 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Miči 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Miči 10mm")

Marlin/src/lcd/language/language_it.h

@@ -197,7 +197,7 @@
 #define MSG_MOVE_Z                          _UxGT("Muovi Z")
 #define MSG_MOVE_E                          _UxGT("Estrusore")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Ugello freddo")
-#define MSG_MOVE_0025MM                     _UxGT("Muovi di 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Muovi di %smm")
 #define MSG_MOVE_01MM                       _UxGT("Muovi di 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Muovi di 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Muovi di 10mm")

Marlin/src/lcd/language/language_jp-kana.h

@@ -82,7 +82,7 @@
 #define MSG_MOVE_Y                          _UxGT("Yジク イドウ")                  // "Move Y"
 #define MSG_MOVE_Z                          _UxGT("Zジク イドウ")                  // "Move Z"
 #define MSG_MOVE_E                          _UxGT("エクストルーダー")                // "Extruder"
-#define MSG_MOVE_0025MM                     _UxGT("0.025mm イドウ")               // "Move 0.025mm"
+#define MSG_MOVE_Z_DIST                     _UxGT("%smm イドウ")                  // "Move 0.025mm"
 #define MSG_MOVE_01MM                       _UxGT("0.1mm イドウ")                 // "Move 0.1mm"
 #define MSG_MOVE_1MM                        _UxGT("  1mm イドウ")                 // "Move 1mm"
 #define MSG_MOVE_10MM                       _UxGT(" 10mm イドウ")                 // "Move 10mm"

Marlin/src/lcd/language/language_ko_KR.h

@@ -177,7 +177,7 @@
 #define MSG_MOVE_Y                          _UxGT("Move Y")
 #define MSG_MOVE_Z                          _UxGT("Move Z")
 #define MSG_MOVE_E                          _UxGT("Extruder")
-#define MSG_MOVE_0025MM                     _UxGT("Move 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Move %smm")
 #define MSG_MOVE_01MM                       _UxGT("Move 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Move 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Move 10mm")

Marlin/src/lcd/language/language_nl.h

@@ -80,7 +80,7 @@
 #define MSG_MOVE_Y                          _UxGT("Verplaats Y")
 #define MSG_MOVE_Z                          _UxGT("Verplaats Z")
 #define MSG_MOVE_E                          _UxGT("Extruder")
-#define MSG_MOVE_0025MM                     _UxGT("Verplaats 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Verplaats %smm")
 #define MSG_MOVE_01MM                       _UxGT("Verplaats 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Verplaats 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Verplaats 10mm")

Marlin/src/lcd/language/language_pl.h

@@ -70,7 +70,7 @@
 #define MSG_MOVE_Y                          _UxGT("Przesuń w Y")
 #define MSG_MOVE_Z                          _UxGT("Przesuń w Z")
 #define MSG_MOVE_E                          _UxGT("Ekstruzja (os E)")
-#define MSG_MOVE_0025MM                     _UxGT("Przesuń co .025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Przesuń co %smm")
 #define MSG_MOVE_01MM                       _UxGT("Przesuń co .1mm")
 #define MSG_MOVE_1MM                        _UxGT("Przesuń co 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Przesuń co 10mm")

Marlin/src/lcd/language/language_pt-br.h

@@ -189,7 +189,7 @@
 #define MSG_MOVE_Z                          _UxGT("Mover Z")
 #define MSG_MOVE_E                          _UxGT("Mover Extrusor")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Extrus. mto fria")
-#define MSG_MOVE_0025MM                     _UxGT("Mover 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mover %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mover 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mover 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mover 10mm")

Marlin/src/lcd/language/language_pt.h

@@ -70,7 +70,7 @@
 #define MSG_MOVE_Y                          _UxGT("Mover Y")
 #define MSG_MOVE_Z                          _UxGT("Mover Z")
 #define MSG_MOVE_E                          _UxGT("Mover Extrusor")
-#define MSG_MOVE_0025MM                     _UxGT("Mover 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Mover %smm")
 #define MSG_MOVE_01MM                       _UxGT("Mover 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Mover 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Mover 10mm")

Marlin/src/lcd/language/language_ru.h

@@ -168,7 +168,7 @@
 #define MSG_MOVE_Y                          _UxGT("Движение по Y")
 #define MSG_MOVE_Z                          _UxGT("Движение по Z")
 #define MSG_MOVE_E                          _UxGT("Экструдер")
-#define MSG_MOVE_0025MM                     _UxGT("Движение 0.025мм")
+#define MSG_MOVE_Z_DIST                     _UxGT("Движение %sмм")
 #define MSG_MOVE_01MM                       _UxGT("Движение 0.1мм")
 #define MSG_MOVE_1MM                        _UxGT("Движение 1мм")
 #define MSG_MOVE_10MM                       _UxGT("Движение 10мм")

Marlin/src/lcd/language/language_sk.h

@@ -206,7 +206,7 @@
 #define MSG_MOVE_Z                          _UxGT("Posunúť Z")
 #define MSG_MOVE_E                          _UxGT("Extrudér")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Hotend je studený")
-#define MSG_MOVE_0025MM                     _UxGT("Posunúť o 0,025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Posunúť o %smm")
 #define MSG_MOVE_01MM                       _UxGT("Posunúť o 0,1mm")
 #define MSG_MOVE_1MM                        _UxGT("Posunúť o 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Posunúť o 10mm")

Marlin/src/lcd/language/language_tr.h

@@ -186,7 +186,7 @@
 #define MSG_MOVE_Z                          _UxGT("Z Hareketi")
 #define MSG_MOVE_E                          _UxGT("Ekstruder")
 #define MSG_HOTEND_TOO_COLD                 _UxGT("Nozul Çok Soğuk")
-#define MSG_MOVE_0025MM                     _UxGT("0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("%smm")
 #define MSG_MOVE_01MM                       _UxGT("0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("1mm")
 #define MSG_MOVE_10MM                       _UxGT("10mm")

Marlin/src/lcd/language/language_uk.h

@@ -72,7 +72,7 @@
 #define MSG_MOVE_Y                          _UxGT("Рух по Y")
 #define MSG_MOVE_Z                          _UxGT("Рух по Z")
 #define MSG_MOVE_E                          _UxGT("Екструдер")
-#define MSG_MOVE_0025MM                     _UxGT("Рух по 0.025mm")
+#define MSG_MOVE_Z_DIST                     _UxGT("Рух по %smm")
 #define MSG_MOVE_01MM                       _UxGT("Рух по 0.1mm")
 #define MSG_MOVE_1MM                        _UxGT("Рух по 1mm")
 #define MSG_MOVE_10MM                       _UxGT("Рух по 10mm")

Marlin/src/lcd/language/language_zh_CN.h

@@ -164,7 +164,7 @@
 #define MSG_MOVE_Y                          _UxGT("移动Y")  //"Move Y"
 #define MSG_MOVE_Z                          _UxGT("移动Z")  //"Move Z"
 #define MSG_MOVE_E                          _UxGT("挤出机")  //"Extruder"
-#define MSG_MOVE_0025MM                     _UxGT("移动 0.025 mm")  //"Move 0.025mm"
+#define MSG_MOVE_Z_DIST                     _UxGT("移动 %s mm")  //"Move 0.025mm"
 #define MSG_MOVE_01MM                       _UxGT("移动 0.1 mm")  //"Move 0.1mm"
 #define MSG_MOVE_1MM                        _UxGT("移动 1 mm")  //"Move 1mm"
 #define MSG_MOVE_10MM                       _UxGT("移动 10 mm")  //"Move 10mm"

Marlin/src/lcd/language/language_zh_TW.h

@@ -164,7 +164,7 @@
 #define MSG_MOVE_Y                          _UxGT("移動Y")  //"Move Y"
 #define MSG_MOVE_Z                          _UxGT("移動Z")  //"Move Z"
 #define MSG_MOVE_E                          _UxGT("擠出機")  //"Extruder"
-#define MSG_MOVE_0025MM                     _UxGT("移動 0.025 mm")  //"Move 0.025mm"
+#define MSG_MOVE_Z_DIST                     _UxGT("移動 %s mm")  //"Move 0.025mm"
 #define MSG_MOVE_01MM                       _UxGT("移動 0.1 mm")  //"Move 0.1mm"
 #define MSG_MOVE_1MM                        _UxGT("移動 1 mm")  //"Move 1mm"
 #define MSG_MOVE_10MM                       _UxGT("移動 10 mm")  //"Move 10mm"

Marlin/src/lcd/menu/menu_motion.cpp

@@ -29,6 +29,13 @@
 #if HAS_LCD_MENU
 
 #include "menu.h"
+
+#include "../lcdprint.h"
+
+#if HAS_GRAPHICAL_LCD
+  #include "../dogm/ultralcd_DOGM.h"
+#endif
+
 #include "../../module/motion.h"
 
 #if ENABLED(DELTA)
@@ -230,6 +237,10 @@ inline void lcd_move_e() { _lcd_move_e(); }
 // "Motion" > "Move Xmm" > "Move XYZ" submenu
 //
 
+#ifndef SHORT_MANUAL_Z_MOVE
+  #define SHORT_MANUAL_Z_MOVE 0.025
+#endif
+
 screenFunc_t _manual_move_func_ptr;
 
 void _goto_manual_move(const float scale) {
@@ -240,7 +251,6 @@ void _goto_manual_move(const float scale) {
 void menu_move_10mm()   { _goto_manual_move(10); }
 void menu_move_1mm()    { _goto_manual_move( 1); }
 void menu_move_01mm()   { _goto_manual_move( 0.1f); }
-void menu_move_0025mm() { _goto_manual_move( 0.025f); }
 
 void _menu_move_distance(const AxisEnum axis, const screenFunc_t func, const int8_t eindex=-1) {
   _manual_move_func_ptr = func;
@@ -268,8 +278,18 @@ void _menu_move_distance(const AxisEnum axis, const screenFunc_t func, const int
     MENU_ITEM(submenu, MSG_MOVE_10MM, menu_move_10mm);
     MENU_ITEM(submenu, MSG_MOVE_1MM, menu_move_1mm);
     MENU_ITEM(submenu, MSG_MOVE_01MM, menu_move_01mm);
-    if (axis == Z_AXIS)
+    if (axis == Z_AXIS && (SHORT_MANUAL_Z_MOVE) > 0.0f && (SHORT_MANUAL_Z_MOVE) < 0.1f) {
-      MENU_ITEM(submenu, MSG_MOVE_0025MM, menu_move_0025mm);
+      MENU_ITEM(submenu, "", []{ _goto_manual_move(float(SHORT_MANUAL_Z_MOVE)); });
+      MENU_ITEM_ADDON_START(1);
+        char tmp[20], numstr[10];
+        // Determine digits needed right of decimal
+        const uint8_t digs = !UNEAR_ZERO((SHORT_MANUAL_Z_MOVE) * 1000 - int((SHORT_MANUAL_Z_MOVE) * 1000)) ? 4 :
+                             !UNEAR_ZERO((SHORT_MANUAL_Z_MOVE) *  100 - int((SHORT_MANUAL_Z_MOVE) *  100)) ? 3 : 2;
+        dtostrf(SHORT_MANUAL_Z_MOVE, 1, digs, numstr);
+        sprintf_P(tmp, PSTR(MSG_MOVE_Z_DIST), numstr);
+        LCDPRINT(tmp);
+      MENU_ITEM_ADDON_END();
+    }
   }
   END_MENU();
 }

config/default/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/A2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/A2plus/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/A6/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/A8/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/A8plus/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Anet/E16/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/ArmEd/Configuration_adv.h

@@ -654,6 +654,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Cartesio/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-10/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-20/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/CR-8/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 0 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Einstart-S/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Felix/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -654,6 +654,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -654,6 +654,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/A10/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/JGAurora/A1/Configuration_adv.h

@@ -655,6 +655,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/JGAurora/A5/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 80*60, 80*60, 12*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -655,6 +655,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/MakerParts/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Malyan/M150/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Malyan/M200/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Mks/Robin/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Mks/Sbase/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/RigidBot/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/SCARA/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Sanguinololu/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -646,6 +646,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/TheBorg/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/TinyBoy2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen

config/examples/VORONDesign/Configuration_adv.h

@@ -650,6 +650,7 @@
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
   #if ENABLED(ULTIPANEL)
     #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
     #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen