|
|
|
@ -1,9 +1,9 @@ |
|
|
|
/**
|
|
|
|
* Marlin 3D Printer Firmware |
|
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
* |
|
|
|
* Based on Sprinter and grbl. |
|
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm |
|
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|
|
|
* |
|
|
|
* This program is free software: you can redistribute it and/or modify |
|
|
|
* it under the terms of the GNU General Public License as published by |
|
|
|
@ -19,29 +19,25 @@ |
|
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
|
* |
|
|
|
*/ |
|
|
|
#pragma once |
|
|
|
|
|
|
|
/**
|
|
|
|
* HJC2560-C Rev2.x pin assignments |
|
|
|
*/ |
|
|
|
|
|
|
|
/**
|
|
|
|
* Rev 2.x 2 Aug 2018 |
|
|
|
*/ |
|
|
|
|
|
|
|
#ifndef __AVR_ATmega2560__ |
|
|
|
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu." |
|
|
|
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" |
|
|
|
#endif |
|
|
|
|
|
|
|
// BOARD Info
|
|
|
|
#define DEFAULT_MACHINE_NAME "HCMaker7" |
|
|
|
#define BOARD_NAME "HJC2560-C" |
|
|
|
#define BOARD_REV "Rev: 2.1" //主板版本：Rev 2.1, Rs=0.05R
|
|
|
|
#define R_SENSOR "R-sensor: R050" //检测电阻
|
|
|
|
|
|
|
|
// FIRMWARE Info
|
|
|
|
#define FIRMWARE_NAME "Marlin 1-1-9" |
|
|
|
#define FIRMWARE_REV "Rev: 1.4" //固件版本：Rev 1.4
|
|
|
|
#define BOARD_INFO_NAME "HJC2560-C" |
|
|
|
|
|
|
|
//
|
|
|
|
// Servos
|
|
|
|
//
|
|
|
|
//#ifndef SERVO0_PIN
|
|
|
|
// #define SERVO0_PIN 11
|
|
|
|
//#endif
|
|
|
|
|
|
|
|
//
|
|
|
|
// Limit Switches
|
|
|
|
@ -49,7 +45,7 @@ |
|
|
|
#define X_STOP_PIN 22 |
|
|
|
#define Y_STOP_PIN 26 |
|
|
|
#define Z_STOP_PIN 29 |
|
|
|
#define EXP_STOP_PIN 28 |
|
|
|
//#define EXP_STOP_PIN 28
|
|
|
|
|
|
|
|
//
|
|
|
|
// Steppers
|
|
|
|
@ -97,9 +93,9 @@ |
|
|
|
#define HEATER_1_PIN 3 |
|
|
|
#define HEATER_BED_PIN 4 |
|
|
|
|
|
|
|
//#ifndef FAN_PIN
|
|
|
|
#ifndef FAN_PIN |
|
|
|
#define FAN_PIN 7 //默认不使用PWM_FAN冷却喷嘴，如果需要，则取消注释
|
|
|
|
//#endif
|
|
|
|
#endif |
|
|
|
|
|
|
|
//
|
|
|
|
// Misc. Functions
|
|
|
|
@ -108,49 +104,55 @@ |
|
|
|
#define SD_DETECT_PIN 39 |
|
|
|
//#define LED_PIN 8
|
|
|
|
#define CASE_LIGHT_PIN 8 // 8 默认挤出机风扇作为Case LED，如果需要PWM FAN,则需要将FAN_PIN置为7，LED_PIN置为8
|
|
|
|
|
|
|
|
//#define SAFETY_TRIGGERED_PIN 28 // PIN to detect the safety circuit has triggered
|
|
|
|
//#define MAIN_VOLTAGE_MEASURE_PIN 14 // ANALOG PIN to measure the main voltage, with a 100k - 4k7 resitor divider.
|
|
|
|
|
|
|
|
//
|
|
|
|
// M3/M4/M5 - Spindle/Laser Control
|
|
|
|
//
|
|
|
|
#if ENABLED(SPINDLE_LASER_ENABLE) |
|
|
|
#define SPINDLE_DIR_PIN 16 |
|
|
|
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
|
|
|
|
#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM
|
|
|
|
#endif |
|
|
|
|
|
|
|
//
|
|
|
|
// LCD / Controller
|
|
|
|
//
|
|
|
|
#if ENABLED(ULTRA_LCD) |
|
|
|
#if HAS_SPI_LCD |
|
|
|
|
|
|
|
#define BEEPER_PIN 18 |
|
|
|
|
|
|
|
#if ENABLED(NEWPANEL) |
|
|
|
|
|
|
|
#if ENABLED(HJC_LCD_SMART_CONTROLLER) |
|
|
|
#define LCD_PINS_RS 20 // LCD_CS
|
|
|
|
#define LCD_PINS_ENABLE 15 // LCD_SDA
|
|
|
|
#define LCD_PINS_D4 14 // LCD_SCK
|
|
|
|
|
|
|
|
#if ENABLED(HJC_LCD_SMART_CONTROLLER) |
|
|
|
#define LCD_BACKLIGHT_PIN 5 // LCD_Backlight
|
|
|
|
//#ifndef LCD_CONTRAST_PIN
|
|
|
|
// #define LCD_CONTRAST_PIN 5 // LCD_Contrast
|
|
|
|
//#endif
|
|
|
|
// define digital pin 24 for the filament runout sensor.
|
|
|
|
#ifndef FIL_RUNOUT_PIN |
|
|
|
#define FIL_RUNOUT_PIN 24 // Filament runout
|
|
|
|
#endif |
|
|
|
#else |
|
|
|
#define LCD_PINS_RS 20 //LCD_CS
|
|
|
|
#define LCD_PINS_ENABLE 15 //LCD_SDA
|
|
|
|
#define LCD_PINS_D4 14 //LCD_SCK
|
|
|
|
#define LCD_PINS_D5 21 |
|
|
|
#define LCD_PINS_D6 5 |
|
|
|
#define LCD_PINS_D7 6 |
|
|
|
#endif |
|
|
|
|
|
|
|
// buttons are directly attached
|
|
|
|
#define BTN_EN1 41 |
|
|
|
#define BTN_EN2 40 |
|
|
|
#define BTN_ENC 19 |
|
|
|
|
|
|
|
#define SD_DETECT_PIN 39 |
|
|
|
|
|
|
|
#else // !NEWPANEL - Old style panel with shift register
|
|
|
|
#else |
|
|
|
|
|
|
|
// buttons are attached to a shift register
|
|
|
|
// Buttons attached to a shift register
|
|
|
|
#define SHIFT_CLK 38 |
|
|
|
#define SHIFT_LD 42 |
|
|
|
#define SHIFT_OUT 40 |
|
|
|
@ -163,31 +165,6 @@ |
|
|
|
#define LCD_PINS_D6 20 |
|
|
|
#define LCD_PINS_D7 19 |
|
|
|
|
|
|
|
#define SD_DETECT_PIN -1 |
|
|
|
|
|
|
|
#endif // !NEWPANEL
|
|
|
|
|
|
|
|
#endif // ULTRA_LCD
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
// M3/M4/M5 - Spindle/Laser Control，默认，主轴/激光器使用独立的PWM引脚(D9)控制
|
|
|
|
// 如果使用了PWM_FAN,Case_Light和Spindle/Laser, 并希望Spindle/Laser使用CASE_Light的线，则将
|
|
|
|
//SPINDLE_LASER_PWM_PIN 定义为8
|
|
|
|
//
|
|
|
|
#if ENABLED(SPINDLE_LASER_ENABLE) // use the LED_PIN for spindle speed control or case light
|
|
|
|
// #undef LED_PIN
|
|
|
|
#define SPINDLE_DIR_PIN 16 |
|
|
|
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
|
|
|
|
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM，
|
|
|
|
//#else
|
|
|
|
// #undef LED_PIN
|
|
|
|
// #define CASE_LIGHT_PIN 7
|
|
|
|
#endif |
|
|
|
|
|
|
|
//
|
|
|
|
// Servos
|
|
|
|
//
|
|
|
|
//#ifndef SERVO0_PIN
|
|
|
|
// #define SERVO0_PIN 11
|
|
|
|
//#endif
|
|
|
|
#endif // HAS_SPI_LCD
|
|
|
|
|
Scott Lahteine
5 years ago
Scott Lahteine