Group manual move options

Marlin/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/default/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/A2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/A2plus/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/A6/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/A8/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/A8plus/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Anet/E16/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/ArmEd/Configuration_adv.h

@@ -646,12 +646,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60}  // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  //#define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60}  // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Cartesio/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/CR-10/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/CR-8/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 0} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 0 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 2*60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 2*60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Einstart-S/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Felix/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  //#define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    //#define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -646,12 +646,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -646,12 +646,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/A10/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/JGAurora/A5/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {80*60, 80*60, 12*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 80*60, 80*60, 12*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/MakerParts/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Malyan/M150/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Malyan/M200/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Mks/Robin/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Mks/Sbase/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/RigidBot/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/SCARA/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 10*60, 60}  // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 }  // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Sanguinololu/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/TheBorg/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/TinyBoy2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/VORONDesign/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Velleman/K8200/Configuration_adv.h

@@ -655,12 +655,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Velleman/K8400/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {70*60, 70*60, 15*60, 6*60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 70*60, 70*60, 15*60, 6*60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/generic/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -641,11 +641,13 @@
 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE_XYZ 50*60
   #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/makibox/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras

config/examples/wt150/Configuration_adv.h

@@ -642,12 +642,11 @@
 // @section lcd
 
 #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-#endif
-
-#if ENABLED(ULTIPANEL)
-  #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
+  #if ENABLED(ULTIPANEL)
+    #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
+    #define ULTIPANEL_FEEDMULTIPLY  // Encoder sets the feedrate multiplier on the Status Screen
+  #endif
 #endif
 
 // @section extras