🧑‍💻 IS_ULTRA_LCD => HAS_WIRED_LCD

Marlin/src/inc/Conditionals_LCD.h

@@ -41,13 +41,13 @@
  *
  *  DOGLCD                  : Run a Graphical LCD through U8GLib (with MarlinUI)
  *  IS_ULTIPANEL            : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
- *  IS_ULTRA_LCD            : Ultra LCD, not necessarily Ultipanel.
+ *  HAS_WIRED_LCD           : Ultra LCD, not necessarily Ultipanel.
  *  IS_RRD_SC               : Common RRD Smart Controller digital interface pins
  *  IS_RRD_FG_SC            : Common RRD Full Graphical Smart Controller digital interface pins
  *  IS_U8GLIB_ST7920        : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
  *  U8GLIB_SH1106           : SH1106 OLED with I2C interface via U8GLib
  *  IS_U8GLIB_SSD1306       : SSD1306 OLED with I2C interface via U8GLib (U8GLIB_SSD1306)
- *  U8GLIB_SSD1309          : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, IS_ULTRA_LCD, DOGLCD)
+ *  U8GLIB_SSD1309          : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, HAS_WIRED_LCD, DOGLCD)
  *  IS_U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib
  *  IS_U8GLIB_LM6059_AF     : LM6059 with Hardware SPI via U8GLib
  */
@@ -287,7 +287,7 @@
 // 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106
 #if ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106)
   #define HAS_U8GLIB_I2C_OLED 1
-  #define IS_ULTRA_LCD 1
+  #define HAS_WIRED_LCD 1
   #define DOGLCD
 #endif
 
@@ -443,7 +443,7 @@
 #endif
 
 #if EITHER(IS_ULTIPANEL, ULTRA_LCD)
-  #define IS_ULTRA_LCD 1
+  #define HAS_WIRED_LCD 1
 #endif
 
 #if EITHER(IS_ULTIPANEL, REPRAPWORLD_KEYPAD)
@@ -502,8 +502,7 @@
   #endif
 #endif
 
-#if IS_ULTRA_LCD
+#if HAS_WIRED_LCD
-  #define HAS_WIRED_LCD 1
   #if ENABLED(DOGLCD)
     #define HAS_MARLINUI_U8GLIB 1
   #elif IS_TFTGLCD_PANEL

Marlin/src/pins/mega/pins_MEGATRONICS.h

@@ -106,7 +106,7 @@
 //
 #define BEEPER_PIN                            33
 
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
 
   #define LCD_PINS_RS                         16
   #define LCD_PINS_ENABLE                     17
@@ -122,7 +122,7 @@
 
   #define SD_DETECT_PIN                       -1  // RAMPS doesn't use this
 
-#endif // IS_ULTRA_LCD && IS_NEWPANEL
+#endif // HAS_WIRED_LCD && IS_NEWPANEL
 
 //
 // M3/M4/M5 - Spindle/Laser Control

Marlin/src/pins/pins.h

@@ -61,7 +61,7 @@
   #endif
 #endif
 
-#if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
+#if !(BOTH(HAS_WIRED_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
   #define HAS_FREE_AUX2_PINS 1
 #endif
 

Marlin/src/pins/ramps/pins_3DRAG.h

@@ -111,7 +111,7 @@
     #define SPINDLE_LASER_PWM_PIN             46  // Hardware PWM
     #define SPINDLE_LASER_ENA_PIN             62  // Pullup!
     #define SPINDLE_DIR_PIN                   48
-  #elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL)          // Use expansion header if no LCD in use
+  #elif !BOTH(HAS_WIRED_LCD, IS_NEWPANEL)          // Use expansion header if no LCD in use
     #define SPINDLE_LASER_ENA_PIN             16  // Pullup or pulldown!
     #define SPINDLE_DIR_PIN                   17
     #if !NUM_SERVOS                               // Use servo connector if possible
@@ -135,7 +135,7 @@
 //
 // LCD / Controller
 //
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
   #undef BEEPER_PIN
 
   // TODO: Remap EXP1/2 based on adapter
@@ -164,7 +164,7 @@
 
   #define BEEPER_PIN                          33
 
-#endif // IS_ULTRA_LCD && IS_NEWPANEL
+#endif // HAS_WIRED_LCD && IS_NEWPANEL
 
 #if IS_U8GLIB_ST7920
   #define BOARD_ST7920_DELAY_1                 0

Marlin/src/pins/ramps/pins_FELIX2.h

@@ -49,7 +49,7 @@
 //
 // LCD / Controller
 //
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
 
   #define SD_DETECT_PIN                       6
 

Marlin/src/pins/ramps/pins_K8600.h

@@ -69,7 +69,7 @@
 //
 // LCD / Controller
 //
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
   #undef BEEPER_PIN
 
   #undef LCD_PINS_RS

Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h

@@ -172,7 +172,7 @@
   #define LCD_PINS_D6                         32
   #define LCD_PINS_D7                         30
 
-#elif BOTH(BOARD_REV_1_5, IS_ULTRA_LCD)
+#elif BOTH(BOARD_REV_1_5, HAS_WIRED_LCD)
 
   #define BEEPER_PIN                          18
 

Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h

@@ -135,7 +135,7 @@
   #define LCD_BACKLIGHT_PIN                   17  // LCD backlight LED
 #endif
 
-#if !HAS_CUTTER && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
+#if !HAS_CUTTER && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(HAS_WIRED_LCD, IS_NEWPANEL) // try to use IO Header
   #define CASE_LIGHT_PIN                       4  // Hardware PWM  - see if IO Header is available
 #endif
 
@@ -268,7 +268,7 @@
 // M3/M4/M5 - Spindle/Laser Control
 //
 #if HAS_CUTTER
-  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
+  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(HAS_WIRED_LCD, IS_NEWPANEL) // try to use IO Header
 
     #define SPINDLE_LASER_ENA_PIN             10  // Pullup or pulldown!
     #define SPINDLE_LASER_PWM_PIN              4  // Hardware PWM

Marlin/src/pins/teensy2/pins_PRINTRBOARD.h

@@ -121,7 +121,7 @@
 //
 // LCD / Controller
 //
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
 
   #define LCD_PINS_RS                          9  // E1       JP11-11
   #define LCD_PINS_ENABLE                      8  // E0       JP11-10
@@ -163,7 +163,7 @@
 
   #endif
 
-#endif // IS_ULTRA_LCD && IS_NEWPANEL
+#endif // HAS_WIRED_LCD && IS_NEWPANEL
 
 #ifndef SDSS
   #define SDSS                                26  // B6 SDCS

Marlin/src/pins/teensy2/pins_TEENSYLU.h

@@ -145,7 +145,7 @@
 //
 // LCD / Controller
 //
-#if IS_ULTRA_LCD && IS_NEWPANEL
+#if HAS_WIRED_LCD && IS_NEWPANEL
 
   #define BEEPER_PIN                          -1
 
@@ -158,7 +158,7 @@
 
   #define SD_DETECT_PIN                       -1
 
-#endif // IS_ULTRA_LCD && IS_NEWPANEL
+#endif // HAS_WIRED_LCD && IS_NEWPANEL
 
 //
 // M3/M4/M5 - Spindle/Laser Control