Merge patches from bugfix-2.0.x

Marlin/Configuration.h

@@ -99,6 +99,7 @@
 /**
  * Select the serial port on the board to use for communication with the host.
  * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
  * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
@@ -107,9 +108,6 @@
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
- * This allows the connection of wireless adapters (for instance) to non-default port pins.
- * Serial port -1 is the USB emulated serial port, if available.
- *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
 //#define SERIAL_PORT_2 -1
@@ -363,6 +361,7 @@
  *   331 : (3.3V scaled thermistor 1 table for MEGA)
  *   332 : (3.3V scaled thermistor 1 table for DUE)
  *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+ *   202 : 200k thermistor - Copymaster 3D
  *     3 : Mendel-parts thermistor (4.7k pullup)
  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)

Marlin/Configuration_adv.h

@@ -338,15 +338,22 @@
  * Controller Fan
  * To cool down the stepper drivers and MOSFETs.
  *
- * The fan will turn on automatically whenever any stepper is enabled
- * and turn off after a set period after all steppers are turned off.
+ * The fan turns on automatically whenever any driver is enabled and turns
+ * off (or reduces to idle speed) shortly after drivers are turned off.
+ *
  */
 //#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
   //#define CONTROLLER_FAN_PIN -1        // Set a custom pin for the controller fan
-  #define CONTROLLERFAN_SECS 60             // Duration in seconds for the fan to run after all motors are disabled
-  #define CONTROLLERFAN_SPEED 255           // 255 == full speed
-  //#define CONTROLLERFAN_SPEED_Z_ONLY 127  // Reduce noise on machines that keep Z enabled
+  //#define CONTROLLER_FAN_USE_Z_ONLY    // With this option only the Z axis is considered
+  #define CONTROLLERFAN_SPEED_MIN      0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
+  #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
+  #define CONTROLLERFAN_SPEED_IDLE     0 // (0-255) Idle speed, used when motors are disabled
+  #define CONTROLLERFAN_IDLE_TIME     60 // (seconds) Extra time to keep the fan running after disabling motors
+  //#define CONTROLLER_FAN_EDITABLE      // Enable M710 configurable settings
+  #if ENABLED(CONTROLLER_FAN_EDITABLE)
+    #define CONTROLLER_FAN_MENU          // Enable the Controller Fan submenu
+  #endif
 #endif
 
 // When first starting the main fan, run it at full speed for the

Marlin/Makefile

@@ -267,6 +267,8 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1147)
 else ifeq ($(HARDWARE_MOTHERBOARD),1148)
 # MKS GEN L V2
 else ifeq ($(HARDWARE_MOTHERBOARD),1149)
+# Copymaster 3D
+else ifeq ($(HARDWARE_MOTHERBOARD),1150)
 
 #
 # RAMBo and derivatives

Marlin/src/HAL/DUE/HAL.h

@@ -39,7 +39,7 @@
 #include <stdint.h>
 
 // Define MYSERIAL0/1 before MarlinSerial includes!
-#if SERIAL_PORT == -1
+#if SERIAL_PORT == -1 || ENABLED(EMERGENCY_PARSER)
   #define MYSERIAL0 customizedSerial1
 #elif SERIAL_PORT == 0
   #define MYSERIAL0 Serial
@@ -56,7 +56,7 @@
 #ifdef SERIAL_PORT_2
   #if SERIAL_PORT_2 == SERIAL_PORT
     #error "SERIAL_PORT_2 must be different from SERIAL_PORT. Please update your configuration."
-  #elif SERIAL_PORT_2 == -1
+  #elif SERIAL_PORT_2 == -1 || ENABLED(EMERGENCY_PARSER)
     #define MYSERIAL1 customizedSerial2
   #elif SERIAL_PORT_2 == 0
     #define MYSERIAL1 Serial
@@ -94,7 +94,6 @@
   #endif
 #endif
 
-
 #include "MarlinSerial.h"
 #include "MarlinSerialUSB.h"
 

Marlin/src/HAL/DUE/MarlinSerial.cpp

@@ -629,23 +629,13 @@ void MarlinSerial<Cfg>::printFloat(double number, uint8_t digits) {
 
 // If not using the USB port as serial port
 #if SERIAL_PORT >= 0
-
-  // Preinstantiate
-  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT>>;
-
-  // Instantiate
-  MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;
-
+  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT>>;      // Define
+  MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;   // Instantiate
 #endif
 
-#ifdef SERIAL_PORT_2
-
-  // Preinstantiate
-  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>>;
-
-  // Instantiate
-  MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2;
-
+#if defined(SERIAL_PORT_2) && SERIAL_PORT_2 >= 0
+  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>>;    // Define
+  MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2; // Instantiate
 #endif
 
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/MarlinSerial.h

@@ -172,13 +172,9 @@ struct MarlinSerialCfg {
 };
 
 #if SERIAL_PORT >= 0
-
   extern MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;
+#endif
 
-#endif // SERIAL_PORT >= 0
-
-#ifdef SERIAL_PORT_2
-
+#if defined(SERIAL_PORT_2) && SERIAL_PORT_2 >= 0
   extern MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2;
-
 #endif

Marlin/src/HAL/DUE/MarlinSerialUSB.cpp

@@ -29,7 +29,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if SERIAL_PORT == -1
+#if HAS_USB_SERIAL
 
 #include "MarlinSerialUSB.h"
 
@@ -283,8 +283,12 @@ void MarlinSerialUSB::printFloat(double number, uint8_t digits) {
 }
 
 // Preinstantiate
-MarlinSerialUSB customizedSerial1;
-
-#endif // SERIAL_PORT == -1
+#if SERIAL_PORT == -1
+  MarlinSerialUSB customizedSerial1;
+#endif
+#if SERIAL_PORT_2 == -1
+  MarlinSerialUSB customizedSerial2;
+#endif
 
+#endif // HAS_USB_SERIAL
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/MarlinSerialUSB.h

@@ -28,7 +28,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if SERIAL_PORT == -1
+#if HAS_USB_SERIAL
 
 #include <WString.h>
 
@@ -88,6 +88,12 @@ private:
   static void printFloat(double, uint8_t);
 };
 
-extern MarlinSerialUSB customizedSerial1;
+#if SERIAL_PORT == -1
+  extern MarlinSerialUSB customizedSerial1;
+#endif
+
+#if SERIAL_PORT_2 == -1
+  extern MarlinSerialUSB customizedSerial2;
+#endif
 
-#endif // SERIAL_PORT == -1
+#endif // HAS_USB_SERIAL

Marlin/src/HAL/LPC1768/HAL.cpp

@@ -67,9 +67,7 @@ int16_t PARSED_PIN_INDEX(const char code, const int16_t dval) {
   return ind > -1 ? ind : dval;
 }
 
-void flashFirmware(int16_t value) {
-  NVIC_SystemReset();
-}
+void flashFirmware(const int16_t) { NVIC_SystemReset(); }
 
 void HAL_clear_reset_source(void) {
   #if ENABLED(USE_WATCHDOG)

Marlin/src/HAL/LPC1768/HAL.h

@@ -195,7 +195,7 @@ int16_t PARSED_PIN_INDEX(const char code, const int16_t dval);
 void HAL_idletask();
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);
 
 /**
  * set_pwm_frequency

Marlin/src/HAL/STM32/HAL.cpp

@@ -133,6 +133,6 @@ void HAL_adc_start_conversion(const uint8_t adc_pin) { HAL_adc_result = analogRe
 
 uint16_t HAL_adc_get_result() { return HAL_adc_result; }
 
-void flashFirmware(int16_t) { NVIC_SystemReset(); }
+void flashFirmware(const int16_t) { NVIC_SystemReset(); }
 
 #endif // ARDUINO_ARCH_STM32 && !STM32GENERIC

Marlin/src/HAL/STM32/HAL.h

@@ -223,4 +223,4 @@ uint16_t HAL_adc_get_result();
 #define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval)
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);

Marlin/src/HAL/STM32F1/HAL.cpp

@@ -388,6 +388,6 @@ void analogWrite(pin_t pin, int pwm_val8) {
     analogWrite(uint8_t(pin), pwm_val8);
 }
 
-void flashFirmware(int16_t value) { nvic_sys_reset(); }
+void flashFirmware(const int16_t) { nvic_sys_reset(); }
 
 #endif // __STM32F1__

Marlin/src/HAL/STM32F1/HAL.h

@@ -160,6 +160,7 @@ void HAL_idletask();
 
 #ifndef digitalPinHasPWM
   #define digitalPinHasPWM(P) (PIN_MAP[P].timer_device != nullptr)
+  #define NO_COMPILE_TIME_PWM
 #endif
 
 #define CRITICAL_SECTION_START()  uint32_t primask = __get_primask(); (void)__iCliRetVal()
@@ -287,4 +288,4 @@ void analogWrite(pin_t pin, int pwm_val8); // PWM only! mul by 257 in maple!?
 #define JTAGSWD_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_NONE)
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);

Marlin/src/MarlinCore.cpp

@@ -567,7 +567,7 @@ inline void manage_inactivity(const bool ignore_stepper_queue=false) {
   #endif
 
   #if ENABLED(USE_CONTROLLER_FAN)
-    controllerfan_update(); // Check if fan should be turned on to cool stepper drivers down
+    controllerFan.update(); // Check if fan should be turned on to cool stepper drivers down
   #endif
 
   #if ENABLED(AUTO_POWER_CONTROL)
@@ -984,6 +984,10 @@ void setup() {
     SETUP_RUN(leds.setup());
   #endif
 
+  #if ENABLED(USE_CONTROLLER_FAN)     // Set up fan controller to initialize also the default configurations.
+    SETUP_RUN(controllerFan.setup());
+  #endif
+
   SETUP_RUN(ui.init());
   SETUP_RUN(ui.reset_status());       // Load welcome message early. (Retained if no errors exist.)
 
@@ -1047,10 +1051,6 @@ void setup() {
     SETUP_RUN(endstops.enable_z_probe(false));
   #endif
 
-  #if ENABLED(USE_CONTROLLER_FAN)
-    SET_OUTPUT(CONTROLLER_FAN_PIN);
-  #endif
-
   #if HAS_STEPPER_RESET
     SETUP_RUN(enableStepperDrivers());
   #endif

Marlin/src/core/boards.h

@@ -103,6 +103,7 @@
 #define BOARD_HJC2560C_REV2           1147  // ADIMLab Gantry v2
 #define BOARD_TANGO                   1148  // BIQU Tango V1
 #define BOARD_MKS_GEN_L_V2            1149  // MKS GEN L V2
+#define BOARD_COPYMASTER_3D           1150  // Copymaster 3D
 
 //
 // RAMBo and derivatives

Marlin/src/core/macros.h

@@ -21,6 +21,10 @@
  */
 #pragma once
 
+#if !defined(__has_include)
+  #define __has_include(...) 1
+#endif
+
 #define ABCE 4
 #define XYZE 4
 #define ABC  3

Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp

@@ -1611,7 +1611,7 @@
          * numbers for those locations should be 0.
          */
         #ifdef VALIDATE_MESH_TILT
-          auto d_from = []() { DEBUG_ECHOPGM("D from "); };
+          auto d_from = []{ DEBUG_ECHOPGM("D from "); };
           auto normed = [&](const xy_pos_t &pos, const float &zadd) {
             return normal.x * pos.x + normal.y * pos.y + zadd;
           };

Marlin/src/feature/controllerfan.cpp

@@ -24,60 +24,80 @@
 
 #if ENABLED(USE_CONTROLLER_FAN)
 
+#include "controllerfan.h"
 #include "../module/stepper/indirection.h"
 #include "../module/temperature.h"
 
-uint8_t controllerfan_speed;
+ControllerFan controllerFan;
 
-void controllerfan_update() {
+uint8_t ControllerFan::speed;
+
+#if ENABLED(CONTROLLER_FAN_EDITABLE)
+  controllerFan_settings_t ControllerFan::settings; // {0}
+#endif
+
+void ControllerFan::setup() {
+  SET_OUTPUT(CONTROLLER_FAN_PIN);
+  init();
+}
+
+void ControllerFan::set_fan_speed(const uint8_t s) {
+  speed = s < (CONTROLLERFAN_SPEED_MIN) ? 0 : s; // Fan OFF below minimum
+}
+
+void ControllerFan::update() {
   static millis_t lastMotorOn = 0,    // Last time a motor was turned on
                   nextMotorCheck = 0; // Last time the state was checked
   const millis_t ms = millis();
   if (ELAPSED(ms, nextMotorCheck)) {
     nextMotorCheck = ms + 2500UL; // Not a time critical function, so only check every 2.5s
 
-    const bool xory = X_ENABLE_READ() == bool(X_ENABLE_ON) || Y_ENABLE_READ() == bool(Y_ENABLE_ON);
+    #define MOTOR_IS_ON(A,B) (A##_ENABLE_READ() == bool(B##_ENABLE_ON))
+    #define _OR_ENABLED_E(N) || MOTOR_IS_ON(E##N,E)
 
-    // If any of the drivers or the bed are enabled...
-    if (xory || Z_ENABLE_READ() == bool(Z_ENABLE_ON)
-      #if HAS_HEATED_BED
-        || thermalManager.temp_bed.soft_pwm_amount > 0
-      #endif
-      #if HAS_X2_ENABLE
-        || X2_ENABLE_READ() == bool(X_ENABLE_ON)
-      #endif
-      #if HAS_Y2_ENABLE
-        || Y2_ENABLE_READ() == bool(Y_ENABLE_ON)
-      #endif
+    const bool motor_on = MOTOR_IS_ON(Z,Z)
       #if HAS_Z2_ENABLE
-        || Z2_ENABLE_READ() == bool(Z_ENABLE_ON)
+        || MOTOR_IS_ON(Z2,Z)
       #endif
       #if HAS_Z3_ENABLE
-        || Z3_ENABLE_READ() == bool(Z_ENABLE_ON)
+        || MOTOR_IS_ON(Z3,Z)
       #endif
       #if HAS_Z4_ENABLE
-        || Z4_ENABLE_READ() == bool(Z_ENABLE_ON)
+        || MOTOR_IS_ON(Z4,Z)
+      #endif
+      || (DISABLED(CONTROLLER_FAN_USE_Z_ONLY) && (
+          MOTOR_IS_ON(X,X) || MOTOR_IS_ON(Y,Y)
+          #if HAS_X2_ENABLE
+            || MOTOR_IS_ON(X2,X)
+          #endif
+          #if HAS_Y2_ENABLE
+            || MOTOR_IS_ON(Y2,Y)
           #endif
           #if E_STEPPERS
-        #define _OR_ENABLED_E(N) || E##N##_ENABLE_READ() == bool(E_ENABLE_ON)
             REPEAT(E_STEPPERS, _OR_ENABLED_E)
           #endif
-    ) {
-      lastMotorOn = ms; //... set time to NOW so the fan will turn on
-    }
+        )
+      )
+    ;
 
-    // Fan off if no steppers have been enabled for CONTROLLERFAN_SECS seconds
-    controllerfan_speed = (!lastMotorOn || ELAPSED(ms, lastMotorOn + (CONTROLLERFAN_SECS) * 1000UL)) ? 0 : (
-      #ifdef CONTROLLERFAN_SPEED_Z_ONLY
-        xory ? CONTROLLERFAN_SPEED : CONTROLLERFAN_SPEED_Z_ONLY
-      #else
-        CONTROLLERFAN_SPEED
+    // If any of the drivers or the heated bed are enabled...
+    if (motor_on
+      #if HAS_HEATED_BED
+        || thermalManager.temp_bed.soft_pwm_amount > 0
       #endif
+    ) lastMotorOn = ms; //... set time to NOW so the fan will turn on
+
+    // Fan Settings. Set fan > 0:
+    //  - If AutoMode is on and steppers have been enabled for CONTROLLERFAN_IDLE_TIME seconds.
+    //  - If System is on idle and idle fan speed settings is activated.
+    set_fan_speed(
+      settings.auto_mode && lastMotorOn && PENDING(ms, lastMotorOn + settings.duration * 1000UL)
+      ? settings.active_speed : settings.idle_speed
     );
 
     // Allow digital or PWM fan output (see M42 handling)
-    WRITE(CONTROLLER_FAN_PIN, controllerfan_speed);
-    analogWrite(pin_t(CONTROLLER_FAN_PIN), controllerfan_speed);
+    WRITE(CONTROLLER_FAN_PIN, speed);
+    analogWrite(pin_t(CONTROLLER_FAN_PIN), speed);
   }
 }
 

Marlin/src/feature/controllerfan.h

@@ -21,4 +21,56 @@
  */
 #pragma once
 
-void controllerfan_update();
+#include "../inc/MarlinConfigPre.h"
+
+typedef struct {
+  uint8_t   active_speed,    // 0-255 (fullspeed); Speed with enabled stepper motors
+            idle_speed;      // 0-255 (fullspeed); Speed after idle period with all motors are disabled
+  uint16_t  duration;        // Duration in seconds for the fan to run after all motors are disabled
+  bool      auto_mode;       // Default true
+} controllerFan_settings_t;
+
+#ifndef CONTROLLERFAN_SPEED_ACTIVE
+  #define CONTROLLERFAN_SPEED_ACTIVE 255
+#endif
+#ifndef CONTROLLERFAN_SPEED_IDLE
+  #define CONTROLLERFAN_SPEED_IDLE     0
+#endif
+#ifndef CONTROLLERFAN_IDLE_TIME
+  #define CONTROLLERFAN_IDLE_TIME     60
+#endif
+
+static constexpr controllerFan_settings_t controllerFan_defaults = {
+  CONTROLLERFAN_SPEED_ACTIVE,
+  CONTROLLERFAN_SPEED_IDLE,
+  CONTROLLERFAN_IDLE_TIME,
+  true
+};
+
+#if ENABLED(USE_CONTROLLER_FAN)
+
+class ControllerFan {
+  private:
+    static uint8_t speed;
+    static void set_fan_speed(const uint8_t s);
+
+  public:
+    #if ENABLED(CONTROLLER_FAN_EDITABLE)
+      static controllerFan_settings_t settings;
+    #else
+      static const controllerFan_settings_t constexpr &settings = controllerFan_defaults;
+    #endif
+    static inline bool state() { return speed > 0; }
+    static inline void init() { reset(); }
+    static inline void reset() {
+      #if ENABLED(CONTROLLER_FAN_EDITABLE)
+        settings = controllerFan_defaults;
+      #endif
+    }
+    static void setup();
+    static void update();
+};
+
+extern ControllerFan controllerFan;
+
+#endif

Marlin/src/feature/power.cpp

@@ -46,8 +46,8 @@ bool Power::is_power_needed() {
     HOTEND_LOOP() if (thermalManager.autofan_speed[e]) return true;
   #endif
 
-  #if ENABLED(AUTO_POWER_CONTROLLERFAN, USE_CONTROLLER_FAN) && HAS_CONTROLLER_FAN
-    if (controllerfan_speed) return true;
+  #if BOTH(USE_CONTROLLER_FAN, AUTO_POWER_CONTROLLERFAN)
+    if (controllerFan.state()) return true;
   #endif
 
   #if ENABLED(AUTO_POWER_CHAMBER_FAN)

Marlin/src/gcode/config/M43.cpp

@@ -67,6 +67,7 @@ inline void toggle_pins() {
     else {
       watchdog_refresh();
       report_pin_state_extended(pin, ignore_protection, true, PSTR("Pulsing   "));
+      const bool prior_mode = GET_PINMODE(pin);
       #if AVR_AT90USB1286_FAMILY // Teensy IDEs don't know about these pins so must use FASTIO
         if (pin == TEENSY_E2) {
           SET_OUTPUT(TEENSY_E2);
@@ -95,6 +96,7 @@ inline void toggle_pins() {
           watchdog_refresh();
         }
       }
+      pinMode(pin, prior_mode);
     }
     SERIAL_EOL();
   }

Marlin/src/gcode/control/M42.cpp

@@ -37,16 +37,33 @@
  *
  *  S<byte> Pin status from 0 - 255
  *  I       Flag to ignore Marlin's pin protection
+ *
+ *  M<mode> Pin mode: 0=INPUT  1=OUTPUT  2=INPUT_PULLUP  3=INPUT_PULLDOWN
  */
 void GcodeSuite::M42() {
-  if (!parser.seenval('S')) return;
-  const byte pin_status = parser.value_byte();
-
   const int pin_index = PARSED_PIN_INDEX('P', GET_PIN_MAP_INDEX(LED_PIN));
   if (pin_index < 0) return;
 
   const pin_t pin = GET_PIN_MAP_PIN(pin_index);
 
+  if (!parser.boolval('I') && pin_is_protected(pin)) return protected_pin_err();
+
+  if (parser.seenval('M')) {
+    switch (parser.value_byte()) {
+      case 0: pinMode(pin, INPUT); break;
+      case 1: pinMode(pin, OUTPUT); break;
+      case 2: pinMode(pin, INPUT_PULLUP); break;
+      #ifdef INPUT_PULLDOWN
+        case 3: pinMode(pin, INPUT_PULLDOWN); break;
+      #endif
+      default: SERIAL_ECHOLNPGM("Invalid Pin Mode");
+    }
+    return;
+  }
+
+  if (!parser.seenval('S')) return;
+  const byte pin_status = parser.value_byte();
+
   #if FAN_COUNT > 0
     switch (pin) {
       #if HAS_FAN0
@@ -76,8 +93,6 @@ void GcodeSuite::M42() {
     }
   #endif
 
-  if (!parser.boolval('I') && pin_is_protected(pin)) return protected_pin_err();
-
   pinMode(pin, OUTPUT);
   extDigitalWrite(pin, pin_status);
   analogWrite(pin, pin_status);

Marlin/src/gcode/feature/advance/M900.cpp

@@ -42,7 +42,7 @@
  */
 void GcodeSuite::M900() {
 
-  auto echo_value_oor = [] (const char ltr, const bool ten=true) {
+  auto echo_value_oor = [](const char ltr, const bool ten=true) {
     SERIAL_CHAR('?'); SERIAL_CHAR(ltr);
     SERIAL_ECHOPGM(" value out of range");
     if (ten) SERIAL_ECHOPGM(" (0-10)");

Marlin/src/gcode/feature/controllerfan/M710.cpp

@@ -0,0 +1,81 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include "../../../inc/MarlinConfigPre.h"
+
+#if ENABLED(CONTROLLER_FAN_EDITABLE)
+
+#include "../../gcode.h"
+#include "../../../feature/controllerfan.h"
+
+void M710_report(const bool forReplay) {
+  if (!forReplay) { SERIAL_ECHOLNPGM("; Controller Fan"); SERIAL_ECHO_START(); }
+  SERIAL_ECHOLNPAIR("M710 "
+    "S", int(controllerFan.settings.active_speed),
+    "I", int(controllerFan.settings.idle_speed),
+    "A", int(controllerFan.settings.auto_mode),
+    "D", controllerFan.settings.duration,
+    " ; (", (int(controllerFan.settings.active_speed) * 100) / 255, "%"
+    " ", (int(controllerFan.settings.idle_speed) * 100) / 255, "%)"
+  );
+}
+
+/**
+ * M710: Set controller fan settings
+ *
+ *  R         : Reset to defaults
+ *  S[0-255]  : Fan speed when motors are active
+ *  I[0-255]  : Fan speed when motors are idle
+ *  A[0|1]    : Turn auto mode on or off
+ *  D         : Set auto mode idle duration
+ *
+ * Examples:
+ *   M710                   ; Report current Settings
+ *   M710 R                 ; Reset SIAD to defaults
+ *   M710 I64               ; Set controller fan Idle Speed to 25%
+ *   M710 S255              ; Set controller fan Active Speed to 100%
+ *   M710 S0                ; Set controller fan Active Speed to OFF
+ *   M710 I255 A0           ; Set controller fan Idle Speed to 100% with Auto Mode OFF
+ *   M710 I127 A1 S255 D160 ; Set controller fan idle speed 50%, AutoMode On, Fan speed 100%, duration to 160 Secs
+ */
+void GcodeSuite::M710() {
+
+  const bool seenR = parser.seen('R');
+  if (seenR) controllerFan.reset();
+
+  const bool seenS = parser.seenval('S');
+  if (seenS) controllerFan.settings.active_speed = parser.value_byte();
+
+  const bool seenI = parser.seenval('I');
+  if (seenI) controllerFan.settings.idle_speed = parser.value_byte();
+
+  const bool seenA = parser.seenval('A');
+  if (seenA) controllerFan.settings.auto_mode = parser.value_bool();
+
+  const bool seenD = parser.seenval('D');
+  if (seenD) controllerFan.settings.duration = parser.value_ushort();
+
+  if (!(seenR || seenS || seenI || seenA || seenD))
+    M710_report(false);
+}
+
+#endif // CONTROLLER_FAN_EDITABLE

Marlin/src/gcode/gcode.cpp

@@ -752,6 +752,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
         case 702: M702(); break;                                  // M702: Unload Filament
       #endif
 
+      #if ENABLED(CONTROLLER_FAN_EDITABLE)
+        case 710: M710(); break;                                  // M710: Set Controller Fan settings
+      #endif
+
       #if ENABLED(GCODE_MACROS)
         case 810: case 811: case 812: case 813: case 814:
         case 815: case 816: case 817: case 818: case 819:

Marlin/src/gcode/gcode.h

@@ -972,6 +972,10 @@ private:
     static void M7219();
   #endif
 
+  #if ENABLED(CONTROLLER_FAN_EDITABLE)
+    static void M710();
+  #endif
+
   static void T(const uint8_t tool_index);
 
 };

Marlin/src/inc/Conditionals_LCD.h

@@ -683,6 +683,10 @@
   #define SPI_SPEED SPI_FULL_SPEED
 #endif
 
+#if SERIAL_PORT == -1 || SERIAL_PORT_2 == -1
+  #define HAS_USB_SERIAL 1
+#endif
+
 /**
  * This setting is also used by M109 when trying to calculate
  * a ballpark safe margin to prevent wait-forever situation.

Marlin/src/inc/MarlinConfigPre.h

@@ -37,12 +37,8 @@
 #include "../../Configuration.h"
 
 #ifdef CUSTOM_VERSION_FILE
-  #if defined(__has_include)
-    #if __has_include(XSTR(../../CUSTOM_VERSION_FILE))
-      #include XSTR(../../CUSTOM_VERSION_FILE)
-    #endif
-  #else
-    #include XSTR(../../CUSTOM_VERSION_FILE)
+  #if __has_include(STRINGIFY(../../CUSTOM_VERSION_FILE))
+    #include STRINGIFY(../../CUSTOM_VERSION_FILE)
   #endif
 #endif
 

Marlin/src/inc/SanityCheck.h

@@ -270,6 +270,10 @@
   #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
 #elif defined(CONTROLLERFAN_PIN)
   #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h."
+#elif defined(CONTROLLERFAN_SPEED)
+  #error "CONTROLLERFAN_SPEED is now CONTROLLERFAN_SPEED_ACTIVE. Please update your Configuration_adv.h."
+#elif defined(CONTROLLERFAN_SECS)
+  #error "CONTROLLERFAN_SECS is now CONTROLLERFAN_IDLE_TIME. Please update your Configuration_adv.h."
 #elif defined(MIN_RETRACT)
   #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
 #elif defined(ADVANCE)
@@ -1983,7 +1987,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * Auto Fan check for PWM pins
  */
-#if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255
+#if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255 && DISABLED(NO_COMPILE_TIME_PWM)
   #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255."
   #if HAS_AUTO_FAN_0
     static_assert(PWM_PIN(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF);
@@ -2649,14 +2653,14 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
 #endif
 
 #if ENABLED(BACKLASH_COMPENSATION)
-  #if IS_CORE
-    #error "BACKLASH_COMPENSATION is incompatible with CORE kinematics."
-  #endif
   #ifndef BACKLASH_DISTANCE_MM
     #error "BACKLASH_COMPENSATION requires BACKLASH_DISTANCE_MM"
-  #endif
-  #ifndef BACKLASH_CORRECTION
+  #elif !defined(BACKLASH_CORRECTION)
     #error "BACKLASH_COMPENSATION requires BACKLASH_CORRECTION"
+  #elif IS_CORE
+    constexpr float backlash_arr[] = BACKLASH_DISTANCE_MM;
+    static_assert(!backlash_arr[CORE_AXIS_1] && !backlash_arr[CORE_AXIS_2],
+                  "BACKLASH_COMPENSATION can only apply to " STRINGIFY(NORMAL_AXIS) " with your CORE system.");
   #endif
 #endif
 

Marlin/src/inc/Version.h

@@ -42,7 +42,7 @@
  * version was tagged.
  */
 #ifndef STRING_DISTRIBUTION_DATE
-  #define STRING_DISTRIBUTION_DATE "2020-03-16"
+  #define STRING_DISTRIBUTION_DATE "2020-03-24"
 #endif
 
 /**

Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp

@@ -118,7 +118,7 @@ static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = {
 static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = {
   U8G_ESC_ADR(0),             // instruction mode
   U8G_ESC_CS(1),              // enable chip
-  #if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
+  #if ANY(MKS_MINI_12864, ENDER2_STOCKDISPLAY, FYSETC_MINI_12864)
     UC1701_START_LINE(0),     // set display start line to 0
     UC1701_ADC_REVERSE(0),    // ADC set to reverse
     UC1701_OUT_MODE(1),       // common output mode

Marlin/src/lcd/extui/lib/dgus/DGUSDisplay.cpp

@@ -30,10 +30,6 @@
   #error "More than 2 hotends not implemented on the Display UI design."
 #endif
 
-#include "DGUSDisplay.h"
-#include "DGUSVPVariable.h"
-#include "DGUSDisplayDef.h"
-
 #include "../../ui_api.h"
 
 #include "../../../../MarlinCore.h"
@@ -48,6 +44,10 @@
   #include "../../../../feature/powerloss.h"
 #endif
 
+#include "DGUSDisplay.h"
+#include "DGUSVPVariable.h"
+#include "DGUSDisplayDef.h"
+
 // Preamble... 2 Bytes, usually 0x5A 0xA5, but configurable
 constexpr uint8_t DGUS_HEADER1 = 0x5A;
 constexpr uint8_t DGUS_HEADER2 = 0xA5;
@@ -855,7 +855,7 @@ void DGUSScreenVariableHandler::HandleStepPerMMExtruderChanged(DGUS_VP_Variable
 void DGUSScreenVariableHandler::HandleProbeOffsetZChanged(DGUS_VP_Variable &var, void *val_ptr) {
   DEBUG_ECHOLNPGM("HandleProbeOffsetZChanged");
 
-  const float offset = float(swap16(*(uint16_t*)val_ptr)) / 100.0f;
+  const float offset = float(int16_t(swap16(*(uint16_t*)val_ptr))) / 100.0f;
   ExtUI::setZOffset_mm(offset);
   ScreenHandler.skipVP = var.VP; // don't overwrite value the next update time as the display might autoincrement in parallel
   return;

Marlin/src/lcd/extui/lib/dgus/hiprecy/DGUSDisplayDef.cpp

@@ -283,6 +283,13 @@ const uint16_t VPList_FLCPrinting[] PROGMEM = {
   0x0000
 };
 
+const uint16_t VPList_Z_Offset[] PROGMEM = {
+  #if HOTENDS >= 1
+    VP_SD_Print_ProbeOffsetZ,
+  #endif
+  0x0000
+};
+
 const struct VPMapping VPMap[] PROGMEM = {
   { DGUSLCD_SCREEN_BOOT, VPList_Boot },
   { DGUSLCD_SCREEN_MAIN, VPList_Main },
@@ -291,6 +298,7 @@ const struct VPMapping VPMap[] PROGMEM = {
   { DGUSLCD_SCREEN_STATUS2, VPList_Status2 },
   { DGUSLCD_SCREEN_PREHEAT, VPList_Preheat },
   { DGUSLCD_SCREEN_MANUALMOVE, VPList_ManualMove },
+  { DGUSLCD_SCREEN_Z_OFFSET, VPList_Z_Offset },
   { DGUSLCD_SCREEN_MANUALEXTRUDE, VPList_ManualExtrude },
   { DGUSLCD_SCREEN_FILAMENT_HEATING, VPList_Filament_heating },
   { DGUSLCD_SCREEN_FILAMENT_LOADING, VPList_Filament_load_unload },
@@ -361,7 +369,7 @@ const struct DGUS_VP_Variable ListOfVP[] PROGMEM = {
   #if HOTENDS >= 1
     VPHELPER(VP_T_E0_Is, &thermalManager.temp_hotend[0].celsius, nullptr, DGUSScreenVariableHandler::DGUSLCD_SendFloatAsLongValueToDisplay<0>),
     VPHELPER(VP_T_E0_Set, &thermalManager.temp_hotend[0].target, DGUSScreenVariableHandler::HandleTemperatureChanged, &DGUSScreenVariableHandler::DGUSLCD_SendWordValueToDisplay),
-    VPHELPER(VP_Flowrate_E0, nullptr, DGUSScreenVariableHandler::HandleFlowRateChanged, &DGUSScreenVariableHandler::DGUSLCD_SendWordValueToDisplay),
+    VPHELPER(VP_Flowrate_E0, &planner.flow_percentage[ExtUI::extruder_t::E0], DGUSScreenVariableHandler::HandleFlowRateChanged, &DGUSScreenVariableHandler::DGUSLCD_SendWordValueToDisplay),
     VPHELPER(VP_EPos, &destination.e, nullptr, DGUSScreenVariableHandler::DGUSLCD_SendFloatAsLongValueToDisplay<2>),
     VPHELPER(VP_MOVE_E0, nullptr, &DGUSScreenVariableHandler::HandleManualExtrude, nullptr),
     VPHELPER(VP_E0_CONTROL, &thermalManager.temp_hotend[0].target, &DGUSScreenVariableHandler::HandleHeaterControl, nullptr),

Marlin/src/lcd/extui/lib/dgus/hiprecy/DGUSDisplayDef.h

@@ -35,6 +35,7 @@ enum DGUSLCD_Screens : uint8_t {
   DGUSLCD_SCREEN_FILAMENT_LOADING     =  76,
   DGUSLCD_SCREEN_FILAMENT_UNLOADING   =  82,
   DGUSLCD_SCREEN_MANUALEXTRUDE        =  84,
+  DGUSLCD_SCREEN_Z_OFFSET             =  88,
   DGUSLCD_SCREEN_SDFILELIST           =   3,
   DGUSLCD_SCREEN_SDPRINTMANIPULATION  =   7,
   DGUSLCD_SCREEN_SDPRINTTUNE          =   9,

Marlin/src/lcd/language/language_de.h

@@ -236,6 +236,11 @@ namespace Language_de {
   PROGMEM Language_Str MSG_FAN_SPEED_N                     = _UxGT("Lüfter ~");
   PROGMEM Language_Str MSG_EXTRA_FAN_SPEED                 = _UxGT("Geschw. Extralüfter");
   PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N               = _UxGT("Geschw. Extralüfter ~");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN                  = _UxGT("Lüfter Kontroller");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_IDLE_SPEED       = _UxGT("Lüfter Leerlauf");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_AUTO_ON          = _UxGT("Motorlast Modus");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_SPEED            = _UxGT("Lüfter Motorlast");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_DURATION         = _UxGT("Ausschalt Delay");
   PROGMEM Language_Str MSG_FLOW                            = _UxGT("Flussrate");
   PROGMEM Language_Str MSG_FLOW_N                          = _UxGT("Flussrate ~");
   PROGMEM Language_Str MSG_CONTROL                         = _UxGT("Einstellungen");

Marlin/src/lcd/language/language_en.h

@@ -247,6 +247,11 @@ namespace Language_en {
   PROGMEM Language_Str MSG_STORED_FAN_N                    = _UxGT("Stored Fan ~");
   PROGMEM Language_Str MSG_EXTRA_FAN_SPEED                 = _UxGT("Extra Fan Speed");
   PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N               = _UxGT("Extra Fan Speed ~");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN                  = _UxGT("Controller Fan");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_IDLE_SPEED       = _UxGT("Idle Speed");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_AUTO_ON          = _UxGT("Auto Mode");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_SPEED            = _UxGT("Active Speed");
+  PROGMEM Language_Str MSG_CONTROLLER_FAN_DURATION         = _UxGT("Idle Period");
   PROGMEM Language_Str MSG_FLOW                            = _UxGT("Flow");
   PROGMEM Language_Str MSG_FLOW_N                          = _UxGT("Flow ~");
   PROGMEM Language_Str MSG_CONTROL                         = _UxGT("Control");

Marlin/src/lcd/language/language_tr.h

@@ -606,4 +606,3 @@ namespace Language_tr {
   #define MSG_FIRST_FAN_SPEED       MSG_FAN_SPEED_N
   #define MSG_FIRST_EXTRA_FAN_SPEED MSG_EXTRA_FAN_SPEED_N
 #endif
- 

Marlin/src/lcd/menu/menu.cpp

@@ -193,7 +193,7 @@ DEFINE_MENU_EDIT_ITEM(uint16_3);    // 123        right-justified
 DEFINE_MENU_EDIT_ITEM(uint16_4);    // 1234       right-justified
 DEFINE_MENU_EDIT_ITEM(uint16_5);    // 12345      right-justified
 DEFINE_MENU_EDIT_ITEM(float3);      // 123        right-justified
-DEFINE_MENU_EDIT_ITEM(float52);     // _2.34, 12.34, -2.34 or 123.45, -23.45
+DEFINE_MENU_EDIT_ITEM(float42_52);  // _2.34, 12.34, -2.34 or 123.45, -23.45
 DEFINE_MENU_EDIT_ITEM(float43);     // 1.234
 DEFINE_MENU_EDIT_ITEM(float5);      // 12345      right-justified
 DEFINE_MENU_EDIT_ITEM(float5_25);   // 12345      right-justified (25 increment)
@@ -428,7 +428,7 @@ void scroll_screen(const uint8_t limit, const bool is_menu) {
           MenuEditItemBase::draw_edit_screen(GET_TEXT(MSG_HOTEND_OFFSET_Z), ftostr54sign(hotend_offset[active_extruder].z));
       #endif
       if (do_probe) {
-        MenuEditItemBase::draw_edit_screen(GET_TEXT(MSG_ZPROBE_ZOFFSET), ftostr52sign(probe.offset.z));
+        MenuEditItemBase::draw_edit_screen(GET_TEXT(MSG_ZPROBE_ZOFFSET), BABYSTEP_TO_STR(probe.offset.z));
         #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
           _lcd_zoffset_overlay_gfx(probe.offset.z);
         #endif

Marlin/src/lcd/menu/menu.h

@@ -47,14 +47,18 @@ typedef void (*selectFunc_t)();
   void _lcd_zoffset_overlay_gfx(const float zvalue);
 #endif
 
-#if Z_PROBE_OFFSET_RANGE_MIN >= -9 && Z_PROBE_OFFSET_RANGE_MAX <= 9
-  // Only values from -9.999 to 9.999
-  #define LCD_Z_OFFSET_FUNC(N) ftostr54sign(N)
-  #define LCD_Z_OFFSET_TYPE float43
-#else
-  // Values from -99.99 to 99.99
-  #define LCD_Z_OFFSET_FUNC(N) ftostr52sign(N)
-  #define LCD_Z_OFFSET_TYPE float52
+#if HAS_BED_PROBE
+  #if Z_PROBE_OFFSET_RANGE_MIN >= -9 && Z_PROBE_OFFSET_RANGE_MAX <= 9
+    #define LCD_Z_OFFSET_TYPE float43    // Values from -9.000 to +9.000
+  #else
+    #define LCD_Z_OFFSET_TYPE float42_52 // Values from -99.99 to 99.99
+  #endif
+#endif
+
+#if ENABLED(BABYSTEP_ZPROBE_OFFSET) && Z_PROBE_OFFSET_RANGE_MIN >= -9 && Z_PROBE_OFFSET_RANGE_MAX <= 9
+  #define BABYSTEP_TO_STR(N) ftostr43sign(N)
+#elif ENABLED(BABYSTEPPING)
+  #define BABYSTEP_TO_STR(N) ftostr53sign(N)
 #endif
 
 ////////////////////////////////////////////
@@ -289,7 +293,7 @@ DEFINE_MENU_EDIT_ITEM_TYPE(uint16_3    ,uint16_t ,ui16tostr3rj    ,   1     );
 DEFINE_MENU_EDIT_ITEM_TYPE(uint16_4    ,uint16_t ,ui16tostr4rj    ,   0.1f  );   // 1234       right-justified
 DEFINE_MENU_EDIT_ITEM_TYPE(uint16_5    ,uint16_t ,ui16tostr5rj    ,   0.01f );   // 12345      right-justified
 DEFINE_MENU_EDIT_ITEM_TYPE(float3      ,float    ,ftostr3         ,   1     );   // 123        right-justified
-DEFINE_MENU_EDIT_ITEM_TYPE(float52     ,float    ,ftostr42_52     , 100     );   // _2.34, 12.34, -2.34 or 123.45, -23.45
+DEFINE_MENU_EDIT_ITEM_TYPE(float42_52  ,float    ,ftostr42_52     , 100     );   // _2.34, 12.34, -2.34 or 123.45, -23.45
 DEFINE_MENU_EDIT_ITEM_TYPE(float43     ,float    ,ftostr43sign    ,1000     );   // -1.234, _1.234, +1.234
 DEFINE_MENU_EDIT_ITEM_TYPE(float5      ,float    ,ftostr5rj       ,   1     );   // 12345      right-justified
 DEFINE_MENU_EDIT_ITEM_TYPE(float5_25   ,float    ,ftostr5rj       ,   0.04f );   // 12345      right-justified (25 increment)

Marlin/src/lcd/menu/menu_advanced.cpp

@@ -112,10 +112,10 @@ void menu_cancelobject();
 
     #if ENABLED(LIN_ADVANCE)
       #if EXTRUDERS == 1
-        EDIT_ITEM(float52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
+        EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
       #elif EXTRUDERS > 1
         LOOP_L_N(n, EXTRUDERS)
-          EDIT_ITEM_N(float52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
+          EDIT_ITEM_N(float42_52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
       #endif
     #endif
 
@@ -257,7 +257,7 @@ void menu_cancelobject();
       EDIT_ITEM(bool, MSG_AUTOTEMP, &planner.autotemp_enabled);
       EDIT_ITEM(float3, MSG_MIN, &planner.autotemp_min, 0, float(HEATER_0_MAXTEMP) - 15);
       EDIT_ITEM(float3, MSG_MAX, &planner.autotemp_max, 0, float(HEATER_0_MAXTEMP) - 15);
-      EDIT_ITEM(float52, MSG_FACTOR, &planner.autotemp_factor, 0, 10);
+      EDIT_ITEM(float42_52, MSG_FACTOR, &planner.autotemp_factor, 0, 10);
     #endif
 
     //
@@ -376,12 +376,12 @@ void menu_cancelobject();
     START_MENU();
     BACK_ITEM(MSG_ADVANCED_SETTINGS);
 
-    static float max_accel = _MAX(planner.settings.max_acceleration_mm_per_s2[A_AXIS], planner.settings.max_acceleration_mm_per_s2[B_AXIS], planner.settings.max_acceleration_mm_per_s2[C_AXIS]);
+    const float max_accel = _MAX(planner.settings.max_acceleration_mm_per_s2[A_AXIS], planner.settings.max_acceleration_mm_per_s2[B_AXIS], planner.settings.max_acceleration_mm_per_s2[C_AXIS]);
     // M204 P Acceleration
     EDIT_ITEM_FAST(float5_25, MSG_ACC, &planner.settings.acceleration, 25, max_accel);
 
     // M204 R Retract Acceleration
-    EDIT_ITEM_FAST(float5, MSG_A_RETRACT, &planner.settings.retract_acceleration, 100, max_accel);
+    EDIT_ITEM_FAST(float5, MSG_A_RETRACT, &planner.settings.retract_acceleration, 100, planner.settings.max_acceleration_mm_per_s2[E_AXIS_N(active_extruder)]);
 
     // M204 T Travel Acceleration
     EDIT_ITEM_FAST(float5_25, MSG_A_TRAVEL, &planner.settings.travel_acceleration, 25, max_accel);
@@ -556,10 +556,10 @@ void menu_advanced_settings() {
     SUBMENU(MSG_FILAMENT, menu_advanced_filament);
   #elif ENABLED(LIN_ADVANCE)
     #if EXTRUDERS == 1
-      EDIT_ITEM(float52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
+      EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
     #elif EXTRUDERS > 1
       LOOP_L_N(n, E_STEPPERS)
-        EDIT_ITEM_N(float52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
+        EDIT_ITEM_N(float42_52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
     #endif
   #endif
 

Marlin/src/lcd/menu/menu_configuration.cpp

@@ -138,12 +138,12 @@ void menu_advanced_settings();
     START_MENU();
     BACK_ITEM(MSG_CONFIGURATION);
     #if ENABLED(DUAL_X_CARRIAGE)
-      EDIT_ITEM_FAST(float52, MSG_HOTEND_OFFSET_X, &hotend_offset[1].x, float(X2_HOME_POS - 25), float(X2_HOME_POS + 25), _recalc_offsets);
+      EDIT_ITEM_FAST(float42_52, MSG_HOTEND_OFFSET_X, &hotend_offset[1].x, float(X2_HOME_POS - 25), float(X2_HOME_POS + 25), _recalc_offsets);
     #else
-      EDIT_ITEM_FAST(float52, MSG_HOTEND_OFFSET_X, &hotend_offset[1].x, -99.0, 99.0, _recalc_offsets);
+      EDIT_ITEM_FAST(float42_52, MSG_HOTEND_OFFSET_X, &hotend_offset[1].x, -99.0, 99.0, _recalc_offsets);
     #endif
-    EDIT_ITEM_FAST(float52,   MSG_HOTEND_OFFSET_Y, &hotend_offset[1].y, -99.0, 99.0, _recalc_offsets);
-    EDIT_ITEM_FAST(float52,   MSG_HOTEND_OFFSET_Z, &hotend_offset[1].z, Z_PROBE_LOW_POINT, 10.0, _recalc_offsets);
+    EDIT_ITEM_FAST(float42_52, MSG_HOTEND_OFFSET_Y, &hotend_offset[1].y, -99.0, 99.0, _recalc_offsets);
+    EDIT_ITEM_FAST(float42_52, MSG_HOTEND_OFFSET_Z, &hotend_offset[1].z, Z_PROBE_LOW_POINT, 10.0, _recalc_offsets);
     #if ENABLED(EEPROM_SETTINGS)
       ACTION_ITEM(MSG_STORE_EEPROM, lcd_store_settings);
     #endif
@@ -227,6 +227,24 @@ void menu_advanced_settings();
   }
 #endif
 
+#if ENABLED(CONTROLLER_FAN_MENU)
+
+  #include "../../feature/controllerfan.h"
+
+  void menu_controller_fan() {
+    START_MENU();
+    BACK_ITEM(MSG_CONFIGURATION);
+    EDIT_ITEM_FAST(percent, MSG_CONTROLLER_FAN_IDLE_SPEED, &controllerFan.settings.idle_speed, _MAX(1, CONTROLLERFAN_SPEED_MIN) - 1, 255);
+    EDIT_ITEM(bool, MSG_CONTROLLER_FAN_AUTO_ON, &controllerFan.settings.auto_mode);
+    if (controllerFan.settings.auto_mode) {
+      EDIT_ITEM_FAST(percent, MSG_CONTROLLER_FAN_SPEED, &controllerFan.settings.active_speed, _MAX(1, CONTROLLERFAN_SPEED_MIN) - 1, 255);
+      EDIT_ITEM(uint16_4, MSG_CONTROLLER_FAN_DURATION, &controllerFan.settings.duration, 0, 4800);
+    }
+    END_MENU();
+  }
+
+#endif
+
 #if ENABLED(CASE_LIGHT_MENU)
 
   #include "../../feature/caselight.h"
@@ -320,6 +338,13 @@ void menu_configuration() {
     EDIT_ITEM(LCD_Z_OFFSET_TYPE, MSG_ZPROBE_ZOFFSET, &probe.offset.z, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
   #endif
 
+  //
+  // Set Fan Controller speed
+  //
+  #if ENABLED(CONTROLLER_FAN_MENU)
+    SUBMENU(MSG_CONTROLLER_FAN, menu_controller_fan);
+  #endif
+
   const bool busy = printer_busy();
   if (!busy) {
     #if EITHER(DELTA_CALIBRATION_MENU, DELTA_AUTO_CALIBRATION)

Marlin/src/lcd/menu/menu_delta_calibrate.cpp

@@ -103,7 +103,7 @@ void _man_probe_pt(const xy_pos_t &xy) {
 #endif
 
 void lcd_delta_settings() {
-  auto _recalc_delta_settings = []() {
+  auto _recalc_delta_settings = []{
     #if HAS_LEVELING
       reset_bed_level(); // After changing kinematics bed-level data is no longer valid
     #endif

Marlin/src/lcd/menu/menu_mixer.cpp

@@ -182,7 +182,7 @@ void lcd_mixer_mix_edit() {
     #if CHANNEL_MIX_EDITING
 
       LOOP_S_LE_N(n, 1, MIXING_STEPPERS)
-        EDIT_ITEM_FAST_N(float52, n, MSG_MIX_COMPONENT_N, &mixer.collector[n-1], 0, 10);
+        EDIT_ITEM_FAST_N(float42_52, n, MSG_MIX_COMPONENT_N, &mixer.collector[n-1], 0, 10);
 
       ACTION_ITEM(MSG_CYCLE_MIX, _lcd_mixer_cycle_mix);
       ACTION_ITEM(MSG_COMMIT_VTOOL, _lcd_mixer_commit_vtool);

Marlin/src/lcd/menu/menu_tune.cpp

@@ -65,7 +65,7 @@
     }
     if (ui.should_draw()) {
       const float spm = planner.steps_to_mm[axis];
-      MenuEditItemBase::draw_edit_screen(msg, LCD_Z_OFFSET_FUNC(spm * babystep.accum));
+      MenuEditItemBase::draw_edit_screen(msg, BABYSTEP_TO_STR(spm * babystep.accum));
       #if ENABLED(BABYSTEP_DISPLAY_TOTAL)
         const bool in_view = (true
           #if HAS_GRAPHICAL_LCD
@@ -81,7 +81,7 @@
           #endif
           lcd_put_u8str_P(GET_TEXT(MSG_BABYSTEP_TOTAL));
           lcd_put_wchar(':');
-          lcd_put_u8str(LCD_Z_OFFSET_FUNC(spm * babystep.axis_total[BS_TOTAL_IND(axis)]));
+          lcd_put_u8str(BABYSTEP_TO_STR(spm * babystep.axis_total[BS_TOTAL_IND(axis)]));
         }
       #endif
     }
@@ -232,10 +232,10 @@ void menu_tune() {
   //
   #if ENABLED(LIN_ADVANCE) && DISABLED(SLIM_LCD_MENUS)
     #if EXTRUDERS == 1
-      EDIT_ITEM(float52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
+      EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 999);
     #elif EXTRUDERS > 1
       LOOP_L_N(n, EXTRUDERS)
-        EDIT_ITEM_N(float52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
+        EDIT_ITEM_N(float42_52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 999);
     #endif
   #endif
 

Marlin/src/lcd/ultralcd.cpp

@@ -227,7 +227,7 @@ millis_t MarlinUI::next_button_update_ms; // = 0
     SETCURSOR(col, row);
     if (!string) return;
 
-    auto _newline = [&col, &row]() {
+    auto _newline = [&col, &row]{
       col = 0; row++;                 // Move col to string len (plus space)
       SETCURSOR(0, row);              // Simulate carriage return
     };

Marlin/src/libs/numtostr.cpp

@@ -174,9 +174,9 @@ const char* ftostr12ns(const float &f) {
   return &conv[3];
 }
 
-// Convert signed float to fixed-length string with 12.34 / -2.34 or 023.45 / -23.45 format
+// Convert signed float to fixed-length string with 12.34 / _2.34 / -2.34 or -23.45 / 123.45 format
 const char* ftostr42_52(const float &f) {
-  if (f <= -10 || f >= 100) return ftostr52(f); // need more digits
+  if (f <= -10 || f >= 100) return ftostr52(f); // -23.45 / 123.45
   long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
   conv[2] = (f >= 0 && f < 10) ? ' ' : MINUSOR(i, DIGIMOD(i, 1000));
   conv[3] = DIGIMOD(i, 100);
@@ -198,9 +198,9 @@ const char* ftostr52(const float &f) {
   return &conv[1];
 }
 
-// Convert signed float to fixed-length string with 12.345 / -2.345 or 023.456 / -23.456 format
-const char* ftostr43_53(const float &f) {
-  if (f <= -10 || f >= 100) return ftostr53(f); // need more digits
+// Convert signed float to fixed-length string with 12.345 / _2.345 / -2.345 or -23.45 / 123.45 format
+const char* ftostr53_63(const float &f) {
+  if (f <= -10 || f >= 100) return ftostr63(f); // -23.456 / 123.456
   long i = (f * 10000 + (f < 0 ? -5: 5)) / 10;
   conv[1] = (f >= 0 && f < 10) ? ' ' : MINUSOR(i, DIGIMOD(i, 10000));
   conv[2] = DIGIMOD(i, 1000);
@@ -212,7 +212,7 @@ const char* ftostr43_53(const float &f) {
 }
 
 // Convert signed float to fixed-length string with 023.456 / -23.456 format
-const char* ftostr53(const float &f) {
+const char* ftostr63(const float &f) {
   long i = (f * 10000 + (f < 0 ? -5: 5)) / 10;
   conv[0] = MINUSOR(i, DIGIMOD(i, 100000));
   conv[1] = DIGIMOD(i, 10000);
@@ -310,6 +310,19 @@ const char* ftostr52sign(const float &f) {
   return conv;
 }
 
+// Convert signed float to string with +12.345 format
+const char* ftostr53sign(const float &f) {
+  long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
+  conv[0] = MINUSOR(i, '+');
+  conv[1] = DIGIMOD(i, 10000);
+  conv[2] = DIGIMOD(i, 1000);
+  conv[3] = '.';
+  conv[4] = DIGIMOD(i, 100);
+  conv[5] = DIGIMOD(i, 10);
+  conv[6] = DIGIMOD(i, 1);
+  return conv;
+}
+
 // Convert unsigned float to string with ____4.5, __34.5, _234.5, 1234.5 format
 const char* ftostr51rj(const float &f) {
   const long i = ((f < 0 ? -f : f) * 100 + 5) / 10;

Marlin/src/libs/numtostr.h

@@ -58,17 +58,17 @@ const char* i16tostr4signrj(const int16_t x);
 // Convert unsigned float to string with 1.23 format
 const char* ftostr12ns(const float &x);
 
-// Convert signed float to fixed-length string with 12.34 / -2.34 or 023.45 / -23.45 format
+// Convert signed float to fixed-length string with 12.34 / _2.34 / -2.34 or -23.45 / 123.45 format
 const char* ftostr42_52(const float &x);
 
 // Convert signed float to fixed-length string with 023.45 / -23.45 format
 const char* ftostr52(const float &x);
 
 // Convert signed float to fixed-length string with 12.345 / -2.345 or 023.456 / -23.456 format
-const char* ftostr43_53(const float &x);
+const char* ftostr53_63(const float &x);
 
 // Convert signed float to fixed-length string with 023.456 / -23.456 format
-const char* ftostr53(const float &x);
+const char* ftostr63(const float &x);
 
 // Convert float to fixed-length string with +123.4 / -123.4 format
 const char* ftostr41sign(const float &x);
@@ -91,6 +91,9 @@ const char* ftostr52sp(const float &x);
 // Convert signed float to string with +123.45 format
 const char* ftostr52sign(const float &x);
 
+// Convert signed float to string with +12.345 format
+const char* ftostr53sign(const float &f);
+
 // Convert unsigned float to string with 1234.5 format omitting trailing zeros
 const char* ftostr51rj(const float &x);
 

Marlin/src/module/configuration_store.cpp

@@ -122,6 +122,11 @@
   #include "../feature/probe_temp_comp.h"
 #endif
 
+#include "../feature/controllerfan.h"
+#if ENABLED(CONTROLLER_FAN_EDITABLE)
+  void M710_report(const bool forReplay);
+#endif
+
 #pragma pack(push, 1) // No padding between variables
 
 typedef struct { uint16_t X, Y, Z, X2, Y2, Z2, Z3, Z4, E0, E1, E2, E3, E4, E5; } tmc_stepper_current_t;
@@ -292,6 +297,11 @@ typedef struct SettingsDataStruct {
   //
   int16_t lcd_contrast;                                 // M250 C
 
+  //
+  // Controller fan settings
+  //
+  controllerFan_settings_t controllerFan_settings;      // M710
+
   //
   // POWER_LOSS_RECOVERY
   //
@@ -880,6 +890,19 @@ void MarlinSettings::postprocess() {
       EEPROM_WRITE(lcd_contrast);
     }
 
+    //
+    // Controller Fan
+    //
+    {
+      _FIELD_TEST(controllerFan_settings);
+      #if ENABLED(USE_CONTROLLER_FAN)
+        const controllerFan_settings_t &cfs = controllerFan.settings;
+      #else
+        controllerFan_settings_t cfs = controllerFan_defaults;
+      #endif
+      EEPROM_WRITE(cfs);
+    }
+
     //
     // Power-Loss Recovery
     //
@@ -1719,6 +1742,19 @@ void MarlinSettings::postprocess() {
         #endif
       }
 
+      //
+      // Controller Fan
+      //
+      {
+        _FIELD_TEST(controllerFan_settings);
+        #if ENABLED(CONTROLLER_FAN_EDITABLE)
+          const controllerFan_settings_t &cfs = controllerFan.settings;
+        #else
+          controllerFan_settings_t cfs = { 0 };
+        #endif
+        EEPROM_READ(cfs);
+      }
+
       //
       // Power-Loss Recovery
       //
@@ -2590,6 +2626,13 @@ void MarlinSettings::reset() {
     ui.set_contrast(DEFAULT_LCD_CONTRAST);
   #endif
 
+  //
+  // Controller Fan
+  //
+  #if ENABLED(USE_CONTROLLER_FAN)
+    controllerFan.reset();
+  #endif
+
   //
   // Power-Loss Recovery
   //
@@ -3154,6 +3197,10 @@ void MarlinSettings::reset() {
       SERIAL_ECHOLNPAIR("  M250 C", ui.contrast);
     #endif
 
+    #if ENABLED(CONTROLLER_FAN_EDITABLE)
+      M710_report(forReplay);
+    #endif
+
     #if ENABLED(POWER_LOSS_RECOVERY)
       CONFIG_ECHO_HEADING("Power-Loss Recovery:");
       CONFIG_ECHO_START();

Marlin/src/module/motion.cpp

@@ -218,7 +218,6 @@ inline void report_more_positions() {
 inline void report_logical_position(const xyze_pos_t &rpos) {
   const xyze_pos_t lpos = rpos.asLogical();
   SERIAL_ECHOPAIR_P(X_LBL, lpos.x, SP_Y_LBL, lpos.y, SP_Z_LBL, lpos.z, SP_E_LBL, lpos.e);
-  report_more_positions();
 }
 
 // Report the real current position according to the steppers.
@@ -237,10 +236,14 @@ void report_real_position() {
   #endif
 
   report_logical_position(npos);
+  report_more_positions();
 }
 
 // Report the logical current position according to the most recent G-code command
-void report_current_position() { report_logical_position(current_position); }
+void report_current_position() {
+  report_logical_position(current_position);
+  report_more_positions();
+}
 
 /**
  * Report the logical current position according to the most recent G-code command.
@@ -1776,6 +1779,13 @@ void homeaxis(const AxisEnum axis) {
         #endif
         homing_feedrate(axis)
       );
+
+      #if ENABLED(SENSORLESS_HOMING)
+        planner.synchronize();
+        #if IS_CORE
+          if (axis != NORMAL_AXIS) safe_delay(200);  // Short delay to allow belts to spring back
+        #endif
+      #endif
     }
   #endif
 

Marlin/src/module/thermistor/thermistor_202.h

@@ -0,0 +1,69 @@
+//
+// Unknown 200K thermistor on a Copymaster 3D hotend
+// Temptable sent from dealer technologyoutlet.co.uk
+//
+
+const short temptable_202[][2] PROGMEM = {
+  { OV(   1), 864 },
+  { OV(  35), 300 },
+  { OV(  38), 295 },
+  { OV(  41), 290 },
+  { OV(  44), 285 },
+  { OV(  47), 280 },
+  { OV(  51), 275 },
+  { OV(  55), 270 },
+  { OV(  60), 265 },
+  { OV(  65), 260 },
+  { OV(  70), 255 },
+  { OV(  76), 250 },
+  { OV(  83), 245 },
+  { OV(  90), 240 },
+  { OV(  98), 235 },
+  { OV( 107), 230 },
+  { OV( 116), 225 },
+  { OV( 127), 220 },
+  { OV( 138), 215 },
+  { OV( 151), 210 },
+  { OV( 164), 205 },
+  { OV( 179), 200 },
+  { OV( 195), 195 },
+  { OV( 213), 190 },
+  { OV( 232), 185 },
+  { OV( 253), 180 },
+  { OV( 275), 175 },
+  { OV( 299), 170 },
+  { OV( 325), 165 },
+  { OV( 352), 160 },
+  { OV( 381), 155 },
+  { OV( 411), 150 },
+  { OV( 443), 145 },
+  { OV( 476), 140 },
+  { OV( 511), 135 },
+  { OV( 546), 130 },
+  { OV( 581), 125 },
+  { OV( 617), 120 },
+  { OV( 652), 115 },
+  { OV( 687), 110 },
+  { OV( 720), 105 },
+  { OV( 753), 100 },
+  { OV( 783),  95 },
+  { OV( 812),  90 },
+  { OV( 839),  85 },
+  { OV( 864),  80 },
+  { OV( 886),  75 },
+  { OV( 906),  70 },
+  { OV( 924),  65 },
+  { OV( 940),  60 },
+  { OV( 954),  55 },
+  { OV( 966),  50 },
+  { OV( 976),  45 },
+  { OV( 985),  40 },
+  { OV( 992),  35 },
+  { OV( 998),  30 },
+  { OV(1003),  25 },
+  { OV(1007),  20 },
+  { OV(1011),  15 },
+  { OV(1014),  10 },
+  { OV(1016),   5 },
+  { OV(1018),   0 }
+};

Marlin/src/module/thermistor/thermistors.h

@@ -151,6 +151,9 @@
 #if ANY_THERMISTOR_IS(201) // Pt100 with LMV324 Overlord
   #include "thermistor_201.h"
 #endif
+#if ANY_THERMISTOR_IS(202) // 200K thermistor in Copymaker3D hotend
+  #include "thermistor_202.h"
+#endif
 #if ANY_THERMISTOR_IS(331) // Like table 1, but with 3V3 as input voltage for MEGA
   #include "thermistor_331.h"
 #endif

Marlin/src/pins/linux/pins_RAMPS_LINUX.h

@@ -271,7 +271,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h

@@ -52,7 +52,6 @@
 #define Z_MIN_PIN                          P1_28  // 10k pullup to 3.3V, 1K series
 #define Z_MAX_PIN                          P1_29  // 10k pullup to 3.3V, 1K series
 
-
 //
 // Steppers
 //
@@ -72,7 +71,6 @@
 #define E0_DIR_PIN                         P0_22
 #define E0_ENABLE_PIN                      P0_21
 
-
 //
 // Temperature Sensors
 //  3.3V max when defined as an analog input
@@ -80,7 +78,6 @@
 #define TEMP_0_PIN                      P0_23_A0  // A0 (T0)
 #define TEMP_BED_PIN                    P0_24_A1  // A1 (T1)
 
-
 //
 // Heaters / Fans
 //
@@ -129,7 +126,6 @@
 
 #endif // HAS_SPI_LCD
 
-
 /**
  * SD Card Reader
  *
@@ -146,7 +142,6 @@
 
 #endif // SDSUPPORT
 
-
 /**
  *  PWMS
  *

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h

@@ -172,7 +172,6 @@
       #define E0_ENABLE_PIN                -1
     #endif
 
-
     #if AXIS_DRIVER_TYPE_E1(TMC2130)
       #define E1_CS_PIN                    P0_10
       #undef E1_ENABLE_PIN

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h

@@ -150,7 +150,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h

@@ -175,7 +175,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/lpc1768/pins_MKS_SBASE.h

@@ -313,7 +313,7 @@
  #endif
 #endif
 
-#if MB(MKS_SBASE) && HAS_TMC220x
+#if MB(MKS_SBASE) && HAS_TMC_UART
 
   /**
    * TMC2208/TMC2209 stepper drivers

Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h

@@ -152,7 +152,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h

@@ -120,7 +120,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/lpc1768/pins_SELENA_COMPACT.h

@@ -85,7 +85,6 @@
 #define TEMP_0_PIN                      P0_24_A1  // A1 (TH2)
 #define TEMP_1_PIN                      P0_25_A2  // A2 (TH3)
 
-
 //
 // Heaters / Fans
 //

Marlin/src/pins/lpc1769/pins_AZTEEG_X5_GT.h

@@ -99,7 +99,6 @@
 #define TEMP_0_PIN                      P0_24_A1  // A1 (TH2)
 #define TEMP_1_PIN                      P0_25_A2  // A2 (TH3)
 
-
 //
 // Heaters / Fans
 //

Marlin/src/pins/lpc1769/pins_MKS_SGEN.h

@@ -50,7 +50,7 @@
 //#define BTN_EN1                          P1_23  // EXP2.5
 //#define BTN_EN2                          P1_22  // EXP2.3
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/pins.h

@@ -188,6 +188,8 @@
   #include "ramps/pins_TANGO.h"                 // ATmega2560                             env:mega2560
 #elif MB(MKS_GEN_L_V2)
   #include "ramps/pins_MKS_GEN_L_V2.h"          // ATmega2560                             env:mega2560
+#elif MB(COPYMASTER_3D)
+  #include "ramps/pins_COPYMASTER_3D.h"         // ATmega2560                             env:mega2560
 
 //
 // RAMBo and derivatives
@@ -465,53 +467,53 @@
 //
 
 #elif MB(STM32F103RE)
-  #include "stm32/pins_STM32F1R.h"              // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_STM32F1R.h"            // STM32F1                                env:STM32F103RE
 #elif MB(MALYAN_M200)
-  #include "stm32/pins_MALYAN_M200.h"           // STM32F1                                env:STM32F103CB_malyan
+  #include "stm32f1/pins_MALYAN_M200.h"         // STM32F1                                env:STM32F103CB_malyan
 #elif MB(STM3R_MINI)
-  #include "stm32/pins_STM3R_MINI.h"            // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_STM3R_MINI.h"          // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_PRO_VB)
-  #include "stm32/pins_GTM32_PRO_VB.h"          // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_GTM32_PRO_VB.h"        // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_MINI_A30)
-  #include "stm32/pins_GTM32_MINI_A30.h"        // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_GTM32_MINI_A30.h"      // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_MINI)
-  #include "stm32/pins_GTM32_MINI.h"            // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_GTM32_MINI.h"          // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_REV_B)
-  #include "stm32/pins_GTM32_REV_B.h"           // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_GTM32_REV_B.h"         // STM32F1                                env:STM32F103RE
 #elif MB(MORPHEUS)
-  #include "stm32/pins_MORPHEUS.h"              // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_MORPHEUS.h"            // STM32F1                                env:STM32F103RE
 #elif MB(CHITU3D)
-  #include "stm32/pins_CHITU3D.h"               // STM32F1                                env:STM32F103RE
+  #include "stm32f1/pins_CHITU3D.h"             // STM32F1                                env:STM32F103RE
 #elif MB(MKS_ROBIN)
-  #include "stm32/pins_MKS_ROBIN.h"             // STM32F1                                env:mks_robin
+  #include "stm32f1/pins_MKS_ROBIN.h"           // STM32F1                                env:mks_robin
 #elif MB(MKS_ROBIN_MINI)
-  #include "stm32/pins_MKS_ROBIN_MINI.h"        // STM32F1                                env:mks_robin_mini
+  #include "stm32f1/pins_MKS_ROBIN_MINI.h"      // STM32F1                                env:mks_robin_mini
 #elif MB(MKS_ROBIN_NANO)
-  #include "stm32/pins_MKS_ROBIN_NANO.h"        // STM32F1                                env:mks_robin_nano
+  #include "stm32f1/pins_MKS_ROBIN_NANO.h"      // STM32F1                                env:mks_robin_nano
 #elif MB(MKS_ROBIN_LITE)
-  #include "stm32/pins_MKS_ROBIN_LITE.h"        // STM32F1                                env:mks_robin_lite
+  #include "stm32f1/pins_MKS_ROBIN_LITE.h"      // STM32F1                                env:mks_robin_lite
 #elif MB(BTT_SKR_MINI_V1_1)
-  #include "stm32/pins_BTT_SKR_MINI_V1_1.h"     // STM32F1                                env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
+  #include "stm32f1/pins_BTT_SKR_MINI_V1_1.h"   // STM32F1                                env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
 #elif MB(BTT_SKR_MINI_E3_V1_0)
-  #include "stm32/pins_BTT_SKR_MINI_E3_V1_0.h"  // STM32F1                                env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
+  #include "stm32f1/pins_BTT_SKR_MINI_E3_V1_0.h"  // STM32F1                              env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
 #elif MB(BTT_SKR_MINI_E3_V1_2)
-  #include "stm32/pins_BTT_SKR_MINI_E3_V1_2.h"  // STM32F1                                env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
+  #include "stm32f1/pins_BTT_SKR_MINI_E3_V1_2.h"  // STM32F1                              env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
 #elif MB(BTT_SKR_E3_DIP)
-  #include "stm32/pins_BTT_SKR_E3_DIP.h"        // STM32F1                                env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
+  #include "stm32f1/pins_BTT_SKR_E3_DIP.h"      // STM32F1                                env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB
 #elif MB(JGAURORA_A5S_A1)
-  #include "stm32/pins_JGAURORA_A5S_A1.h"       // STM32F1                                env:jgaurora_a5s_a1
+  #include "stm32f1/pins_JGAURORA_A5S_A1.h"     // STM32F1                                env:jgaurora_a5s_a1
 #elif MB(FYSETC_AIO_II)
-  #include "stm32/pins_FYSETC_AIO_II.h"         // STM32F1                                env:STM32F103RC_fysetc
+  #include "stm32f1/pins_FYSETC_AIO_II.h"       // STM32F1                                env:STM32F103RC_fysetc
 #elif MB(FYSETC_CHEETAH)
-  #include "stm32/pins_FYSETC_CHEETAH.h"        // STM32F1                                env:STM32F103RC_fysetc
+  #include "stm32f1/pins_FYSETC_CHEETAH.h"      // STM32F1                                env:STM32F103RC_fysetc
 #elif MB(FYSETC_CHEETAH_V12)
-  #include "stm32/pins_FYSETC_CHEETAH_V12.h"    // STM32F1                                env:STM32F103RC_fysetc
+  #include "stm32f1/pins_FYSETC_CHEETAH_V12.h"  // STM32F1                                env:STM32F103RC_fysetc
 #elif MB(LONGER3D_LK)
-  #include "stm32/pins_LONGER3D_LK.h"           // STM32F1                                env:STM32F103VE_longer
+  #include "stm32f1/pins_LONGER3D_LK.h"         // STM32F1                                env:STM32F103VE_longer
 #elif MB(MKS_ROBIN_LITE3)
-  #include "stm32/pins_MKS_ROBIN_LITE3.h"       // STM32F1                                env:mks_robin_lite3
+  #include "stm32f1/pins_MKS_ROBIN_LITE3.h"     // STM32F1                                env:mks_robin_lite3
 #elif MB(MKS_ROBIN_PRO)
-  #include "stm32/pins_MKS_ROBIN_PRO.h"         // STM32F1                                env:mks_robin_pro
+  #include "stm32f1/pins_MKS_ROBIN_PRO.h"       // STM32F1                                env:mks_robin_pro
 
 //
 // ARM Cortex-M4F
@@ -527,46 +529,46 @@
 //
 
 #elif MB(BEAST)
-  #include "stm32/pins_BEAST.h"                 // STM32F4                                env:STM32F4
+  #include "stm32f4/pins_BEAST.h"               // STM32F4                                env:STM32F4
 #elif MB(GENERIC_STM32F4)
-  #include "stm32/pins_GENERIC_STM32F4.h"       // STM32F4                                env:STM32F4
+  #include "stm32f4/pins_GENERIC_STM32F4.h"     // STM32F4                                env:STM32F4
 #elif MB(ARMED)
-  #include "stm32/pins_ARMED.h"                 // STM32F4                                env:ARMED
+  #include "stm32f4/pins_ARMED.h"               // STM32F4                                env:ARMED
 #elif MB(RUMBA32_AUS3D)
-  #include "stm32/pins_RUMBA32_AUS3D.h"         // STM32F4                                env:rumba32_f446ve
+  #include "stm32f4/pins_RUMBA32_AUS3D.h"       // STM32F4                                env:rumba32_f446ve
 #elif MB(RUMBA32_MKS)
-  #include "stm32/pins_RUMBA32_MKS.h"           // STM32F4                                env:rumba32_mks
+  #include "stm32f4/pins_RUMBA32_MKS.h"         // STM32F4                                env:rumba32_mks
 #elif MB(BLACK_STM32F407VE)
-  #include "stm32/pins_BLACK_STM32F407VE.h"     // STM32F4                                env:STM32F407VE_black
+  #include "stm32f4/pins_BLACK_STM32F407VE.h"   // STM32F4                                env:STM32F407VE_black
 #elif MB(STEVAL_3DP001V1)
-  #include "stm32/pins_STEVAL_3DP001V1.h"       // STM32F4                                env:STM32F401VE_STEVAL
+  #include "stm32f4/pins_STEVAL_3DP001V1.h"     // STM32F4                                env:STM32F401VE_STEVAL
 #elif MB(BTT_SKR_PRO_V1_1)
-  #include "stm32/pins_BTT_SKR_PRO_V1_1.h"      // STM32F4                                env:BIGTREE_SKR_PRO
+  #include "stm32f4/pins_BTT_SKR_PRO_V1_1.h"    // STM32F4                                env:BIGTREE_SKR_PRO
 #elif MB(BTT_GTR_V1_0)
-  #include "stm32/pins_BTT_GTR_V1_0.h"          // STM32F4                                env:BIGTREE_GTR_V1_0
+  #include "stm32f4/pins_BTT_GTR_V1_0.h"        // STM32F4                                env:BIGTREE_GTR_V1_0
 #elif MB(BTT_BTT002_V1_0)
-  #include "stm32/pins_BTT_BTT002_V1_0.h"       // STM32F4                                env:BIGTREE_BTT002
+  #include "stm32f4/pins_BTT_BTT002_V1_0.h"     // STM32F4                                env:BIGTREE_BTT002
 #elif MB(LERDGE_K)
-  #include "stm32/pins_LERDGE_K.h"              // STM32F4                                env:STM32F4
+  #include "stm32f4/pins_LERDGE_K.h"            // STM32F4                                env:STM32F4
 #elif MB(LERDGE_X)
-  #include "stm32/pins_LERDGE_X.h"              // STM32F4                                env:STM32F4
+  #include "stm32f4/pins_LERDGE_X.h"            // STM32F4                                env:STM32F4
 #elif MB(VAKE403D)
-  #include "stm32/pins_VAKE403D.h"              // STM32F4                                env:STM32F4
+  #include "stm32f4/pins_VAKE403D.h"            // STM32F4                                env:STM32F4
 #elif MB(FYSETC_S6)
-  #include "stm32/pins_FYSETC_S6.h"             // STM32F4                                env:FYSETC_S6
+  #include "stm32f4/pins_FYSETC_S6.h"           // STM32F4                                env:FYSETC_S6
 #elif MB(FLYF407ZG)
-  #include "stm32/pins_FLYF407ZG.h"             // STM32F4                                env:FLYF407ZG
+  #include "stm32f4/pins_FLYF407ZG.h"           // STM32F4                                env:FLYF407ZG
 #elif MB(MKS_ROBIN2)
-  #include "pins_MKS_ROBIN2.h"                  // STM32F4                                env:MKS_ROBIN2
+  #include "stm32f4/pins_MKS_ROBIN2.h"          // STM32F4                                env:MKS_ROBIN2
 
 //
 // ARM Cortex M7
 //
 
 #elif MB(THE_BORG)
-  #include "stm32/pins_THE_BORG.h"              // STM32F7                                env:STM32F7
+  #include "stm32f7/pins_THE_BORG.h"            // STM32F7                                env:STM32F7
 #elif MB(REMRAM_V1)
-  #include "stm32/pins_REMRAM_V1.h"             // STM32F7                                env:STM32F7
+  #include "stm32f7/pins_REMRAM_V1.h"           // STM32F7                                env:STM32F7
 
 //
 // Espressif ESP32

Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h

@@ -96,7 +96,6 @@
 
 #define CASE_LIGHT_PIN                        44  // Hardware PWM
 
-
 // This board has headers for Z-min, Z-max and IND_S_5V *but* as the bq team
 // decided to ship the printer only with the probe and no additional Z-min
 // endstop and the instruction manual advises the user to connect the probe to

Marlin/src/pins/ramps/pins_COPYMASTER_3D.h

@@ -0,0 +1,34 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+#define BOARD_INFO_NAME "Copymaster 3D RAMPS"
+
+#define Z_STEP_PIN        47
+#define Y_MAX_PIN         14
+#define FIL_RUNOUT_PIN    15
+#define SD_DETECT_PIN     66
+
+//
+// Import RAMPS 1.4 pins
+//
+#include "pins_RAMPS.h"

Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h

@@ -117,8 +117,6 @@
   #define MAX6675_SS_PIN                      66  // Don't use 49 (SD_DETECT_PIN)
 #endif
 
-
-
 //
 // Heaters / Fans
 //

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -117,7 +117,7 @@
 // the jumper next to the limit switch socket when using sensorless homing.
 //
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/ramps/pins_FYSETC_F6_14.h

@@ -29,7 +29,7 @@
 
 #define Z_MAX_PIN                              2
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    */

Marlin/src/pins/ramps/pins_MKS_BASE_common.h

@@ -29,7 +29,7 @@
   #define BOARD_INFO_NAME "MKS BASE"
 #endif
 
-#if MKS_BASE_VERSION == 14 || MKS_BASE_VERSION == 15
+#if MKS_BASE_VERSION >= 14
   //
   // Heaters / Fans
   //

Marlin/src/pins/ramps/pins_RAMPS.h

@@ -133,7 +133,9 @@
   #define Y_CS_PIN                            49
 #endif
 
-#define Z_STEP_PIN         46
+#ifndef Z_STEP_PIN
+  #define Z_STEP_PIN                          46
+#endif
 #define Z_DIR_PIN                             48
 #define Z_ENABLE_PIN                          62
 #ifndef Z_CS_PIN
@@ -298,7 +300,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/ramps/pins_TRIGORILLA_14.h

@@ -66,13 +66,13 @@
     #define RAMPS_D8_PIN     TRIGORILLA_FAN0_PIN
   #else
     // EEB
-    #define RAMPS_D8_PIN TRIGORILLA_HEATER_BED_PIN
+    #define RAMPS_D8_PINTRIGORILLA_HEATER_BED_PIN
     #define FAN_PIN          TRIGORILLA_FAN0_PIN  // Override pin 4 in pins_RAMPS.h
   #endif
 #elif TEMP_SENSOR_BED
   // EFB (Anycubic Kossel default)
   #define RAMPS_D9_PIN       TRIGORILLA_FAN0_PIN
-  #define RAMPS_D8_PIN   TRIGORILLA_HEATER_BED_PIN
+  #define RAMPS_D8_PINTRIGORILLA_HEATER_BED_PIN
 #else
   // EFF
   #define RAMPS_D9_PIN       TRIGORILLA_FAN1_PIN
@@ -83,7 +83,7 @@
   #define FAN1_PIN           TRIGORILLA_FAN1_PIN
 #endif
 #define FAN2_PIN             TRIGORILLA_FAN2_PIN
-#define ORIG_E0_AUTO_FAN_PIN TRIGORILLA_FAN2_PIN  // Used in Anycubic Kossel example config
+#define ORIG_E0_AUTO_FAN_PINTRIGORILLA_FAN2_PIN   // Used in Anycubic Kossel example config
 
 #include "pins_RAMPS.h"
 

Marlin/src/pins/ramps/pins_TT_OSCAR.h

@@ -99,7 +99,7 @@
 #define E4_ENABLE_PIN                         47
 #define E4_CS_PIN                      E0_CS_PIN
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/sam/pins_ARCHIM1.h

@@ -59,7 +59,6 @@
 #define SERVO0_PIN                            20  // D20 PB12 (Header J20 20)
 #define SERVO1_PIN                            21  // D21 PB13 (Header J20 19)
 
-
 //
 // Limit Switches
 //
@@ -84,7 +83,6 @@
   #define FIL_RUNOUT2_PIN                     67  // D67 PB16 (Header J20 16)
 #endif
 
-
 //
 // Steppers
 //

Marlin/src/pins/sam/pins_RAMPS_FD_V1.h

@@ -205,7 +205,7 @@
 
 #endif // HAS_SPI_LCD
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/samd/pins_RAMPS_144.h

@@ -171,7 +171,7 @@
   #endif
 #endif
 
-#if HAS_TMC220x
+#if HAS_TMC_UART
   /**
    * TMC2208/TMC2209 stepper drivers
    *

Marlin/src/pins/sanguino/pins_GEN3_PLUS.h

@@ -50,7 +50,6 @@
  *
  */
 
-
 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
   #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'"
 #endif

Marlin/src/pins/sanguino/pins_GEN7_12.h

@@ -74,7 +74,6 @@
 #define Y_MAX_PIN                              2
 #define X_MAX_PIN                              6
 
-
 //
 // Z Probe (when not Z_MIN_PIN)
 //

Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h

@@ -138,7 +138,7 @@
   #define LCD_BACKLIGHT_PIN                   17  // LCD backlight LED
 #endif
 
-#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)  // try to use IO Header
+#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)// try to use IO Header
   #define CASE_LIGHT_PIN                       4  // Hardware PWM  - see if IO Header is available
 #endif
 
@@ -277,7 +277,7 @@
 // M3/M4/M5 - Spindle/Laser Control
 //
 #if HAS_CUTTER
-  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)  // try to use IO Header
+  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)// try to use IO Header
 
     #define SPINDLE_LASER_ENA_PIN             10  // Pullup or pulldown!
     #define SPINDLE_LASER_PWM_PIN              4  // Hardware PWM

Marlin/src/pins/stm32/pins_ARMED.h

@@ -1,201 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-
-//  https://github.com/ktand/Armed
-
-#pragma once
-
-#ifndef STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "Arm'ed supports up to 2 hotends / E-steppers."
-#endif
-
-#ifndef ARMED_V1_0
-  #define ARMED_V1_1
-#endif
-
-#undef BOARD_INFO_NAME // Defined on the command line by Arduino Core STM32
-#define BOARD_INFO_NAME      "Arm'ed"
-#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
-
-#define I2C_EEPROM
-
-#undef E2END // Defined in Arduino Core STM32 to be used with EEPROM emulation. This board uses a real EEPROM.
-#define E2END 0xFFF // 4KB
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PE0
-#define Y_STOP_PIN         PE1
-#define Z_STOP_PIN         PE14
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-//#ifndef Z_MIN_PROBE_PIN
-//  #define Z_MIN_PROBE_PIN  PA4
-//#endif
-
-//
-// Filament Runout Sensor
-//
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN   PA3
-#endif
-
-//
-// Steppers
-//
-
-#ifdef ARMED_SWAP_X_E1
-  #define X_STEP_PIN       PE4
-  #define X_DIR_PIN        PE2
-  #define X_ENABLE_PIN     PE3
-  #define X_CS_PIN         PE5
-#else
-  #define X_STEP_PIN       PD3
-  #define X_DIR_PIN        PD2
-  #define X_ENABLE_PIN     PD0
-  #define X_CS_PIN         PD1
-#endif
-
-#define Y_STEP_PIN         PE11
-#define Y_DIR_PIN          PE10
-#define Y_ENABLE_PIN       PE13
-#define Y_CS_PIN           PE12
-
-#define Z_STEP_PIN         PD6
-#define Z_DIR_PIN          PD7
-#define Z_ENABLE_PIN       PD4
-#define Z_CS_PIN           PD5
-
-#define E0_STEP_PIN        PB5
-#define E0_DIR_PIN         PB6
-#ifdef ARMED_V1_1
-  #define E0_ENABLE_PIN    PC12
-#else
-  #define E0_ENABLE_PIN    PB3
-#endif
-#define E0_CS_PIN          PB4
-
-#ifdef ARMED_SWAP_X_E1
-  #define E1_STEP_PIN      PD3
-  #define E1_DIR_PIN       PD2
-  #define E1_ENABLE_PIN    PD0
-  #define E1_CS_PIN        PD1
-#else
-  #define E1_STEP_PIN      PE4
-  #define E1_DIR_PIN       PE2
-  #define E1_ENABLE_PIN    PE3
-  #define E1_CS_PIN        PE5
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC0   // Analog Input
-#define TEMP_1_PIN         PC1   // Analog Input
-#define TEMP_BED_PIN       PC2   // Analog Input
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PA1   // Hardware PWM
-#define HEATER_1_PIN       PA2   // Hardware PWM
-#define HEATER_BED_PIN     PA0   // Hardware PWM
-
-#define FAN_PIN            PC6   // Hardware PWM, Part cooling fan
-#define FAN1_PIN           PC7   // Hardware PWM, Extruder fan
-#define FAN2_PIN           PC8   // Hardware PWM, Controller fan
-
-//
-// Misc functions
-//
-#define SDSS               PE7
-#define LED_PIN            PB7   // Heart beat
-#define PS_ON_PIN          PA10
-#define KILL_PIN           PA8
-#define PWR_LOSS           PA4   // Power loss / nAC_FAULT
-
-//
-// LCD / Controller
-//
-#define SD_DETECT_PIN      PA15
-#define BEEPER_PIN         PC9
-
-#if ENABLED(FYSETC_MINI_12864)
-  //
-  // See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
-  //
-  #define DOGLCD_A0        PE9
-  #define DOGLCD_CS        PE8
-
-  #define LCD_BACKLIGHT_PIN -1
-
-  #define LCD_RESET_PIN    PB12   // Must be high or open for LCD to operate normally.
-
-  #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
-    #ifndef RGB_LED_R_PIN
-      #define RGB_LED_R_PIN PB13
-    #endif
-    #ifndef RGB_LED_G_PIN
-      #define RGB_LED_G_PIN PB14
-    #endif
-    #ifndef RGB_LED_B_PIN
-      #define RGB_LED_B_PIN PB15
-    #endif
-  #elif ENABLED(FYSETC_MINI_12864_2_1)
-    #define NEOPIXEL_PIN   PB13
-  #endif
-#else
-  #define LCD_PINS_RS      PE9
-  #define LCD_PINS_ENABLE  PE8
-  #define LCD_PINS_D4      PB12
-  #define LCD_PINS_D5      PB13
-  #define LCD_PINS_D6      PB14
-  #define LCD_PINS_D7      PB15
-
-  #if ENABLED(MKS_MINI_12864)
-    #define DOGLCD_CS      PB13
-    #define DOGLCD_A0      PB14
-  #endif
-#endif
-
-#define BTN_EN1            PC4
-#define BTN_EN2            PC5
-#define BTN_ENC            PC3
-
-//
-// Extension pins
-//
-#define EXT0_PIN           PB0
-#define EXT1_PIN           PB1
-#define EXT2_PIN           PB2
-#define EXT3_PIN           PD8
-#define EXT4_PIN           PD9
-#define EXT5_PIN           PD10
-#define EXT6_PIN           PD11
-#define EXT7_PIN           PD12
-#define EXT8_PIN           PB10
-#define EXT9_PIN           PB11

Marlin/src/pins/stm32/pins_BEAST.h

@@ -1,285 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#if !defined(__STM32F1__) && !defined(__STM32F4__)
-  #error "Oops! Select an STM32F1/4 board in 'Tools > Board.'"
-#endif
-
-/**
- * 21017 Victor Perez Marlin for stm32f1 test
- */
-
-#define BOARD_INFO_NAME      "Beast STM32"
-#define DEFAULT_MACHINE_NAME "STM32F103RET6"
-
-// Enable I2C_EEPROM for testing
-#define I2C_EEPROM
-
-// Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PE0
-#define X_DIR_PIN          PE1
-#define X_ENABLE_PIN       PC0
-#define X_MIN_PIN          PD5
-#define X_MAX_PIN          -1
-
-#define Y_STEP_PIN         PE2
-#define Y_DIR_PIN          PE3
-#define Y_ENABLE_PIN       PC1
-#define Y_MIN_PIN          PD6
-#define Y_MAX_PIN
-
-#define Z_STEP_PIN         PE4
-#define Z_DIR_PIN          PE5
-#define Z_ENABLE_PIN       PC2
-#define Z_MIN_PIN          PD7
-#define Z_MAX_PIN          -1
-
-#define Y2_STEP_PIN        -1
-#define Y2_DIR_PIN         -1
-#define Y2_ENABLE_PIN      -1
-
-#define Z2_STEP_PIN        -1
-#define Z2_DIR_PIN         -1
-#define Z2_ENABLE_PIN      -1
-
-#define E0_STEP_PIN        PE6
-#define E0_DIR_PIN         PE7
-#define E0_ENABLE_PIN      PC3
-
-/**
- * TODO: Currently using same Enable pin to all steppers.
- */
-
-#define E1_STEP_PIN        PE8
-#define E1_DIR_PIN         PE9
-#define E1_ENABLE_PIN      PC4
-
-#define E2_STEP_PIN        PE10
-#define E2_DIR_PIN         PE11
-#define E2_ENABLE_PIN      PC5
-
-//
-// Misc. Functions
-//
-#define SDSS               PA15
-#define LED_PIN            PB2
-
-#define PS_ON_PIN          -1
-#define KILL_PIN           -1
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PD12   // EXTRUDER 1
-#define HEATER_1_PIN       PD13
-#define HEATER_2_PIN       PD14
-
-#define HEATER_BED_PIN     PB9   // BED
-#define HEATER_BED2_PIN    -1    // BED2
-#define HEATER_BED3_PIN    -1    // BED3
-
-#ifndef FAN_PIN
-  #define FAN_PIN          PB10
-#endif
-
-#define FAN_SOFT_PWM
-
-//
-// Temperature Sensors
-//
-#define TEMP_BED_PIN       PA0   // Analog Input
-#define TEMP_0_PIN         PA1   // Analog Input
-#define TEMP_1_PIN         PA2   // Analog Input
-#define TEMP_2_PIN         PA3   // Analog Input
-
-//
-// LCD Pins
-//
-#if HAS_SPI_LCD
-
-  #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define LCD_PINS_RS         49   // CS chip select /SS chip slave select
-    #define LCD_PINS_ENABLE     51   // SID (MOSI)
-    #define LCD_PINS_D4         52   // SCK (CLK) clock
-  #elif BOTH(NEWPANEL, PANEL_ONE)
-    #define LCD_PINS_RS         PB8
-    #define LCD_PINS_ENABLE     PD2
-    #define LCD_PINS_D4         PB12
-    #define LCD_PINS_D5         PB13
-    #define LCD_PINS_D6         PB14
-    #define LCD_PINS_D7         PB15
-  #else
-    #define LCD_PINS_RS         PB8
-    #define LCD_PINS_ENABLE     PD2
-    #define LCD_PINS_D4         PB12
-    #define LCD_PINS_D5         PB13
-    #define LCD_PINS_D6         PB14
-    #define LCD_PINS_D7         PB15
-    #if DISABLED(NEWPANEL)
-      #define BEEPER_PIN        33
-      // Buttons attached to a shift register
-      // Not wired yet
-      //#define SHIFT_CLK 38
-      //#define SHIFT_LD 42
-      //#define SHIFT_OUT 40
-      //#define SHIFT_EN 17
-    #endif
-  #endif
-
-  #if ENABLED(NEWPANEL)
-
-    #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
-
-      #define BEEPER_PIN        37
-
-      #define BTN_EN1           31
-      #define BTN_EN2           33
-      #define BTN_ENC           35
-
-      #define SD_DETECT_PIN     49
-      #define KILL_PIN          41
-
-      #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-        #define LCD_BACKLIGHT_PIN 39
-      #endif
-
-    #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-
-      #define BTN_EN1           64
-      #define BTN_EN2           59
-      #define BTN_ENC           63
-      #define SD_DETECT_PIN     42
-
-    #elif ENABLED(LCD_I2C_PANELOLU2)
-
-      #define BTN_EN1           47
-      #define BTN_EN2           43
-      #define BTN_ENC           32
-      #define LCD_SDSS          53
-      #define SD_DETECT_PIN     -1
-      #define KILL_PIN          41
-
-    #elif ENABLED(LCD_I2C_VIKI)
-
-      #define BTN_EN1           22   // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
-      #define BTN_EN2            7   // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
-
-      #define BTN_ENC           -1
-      #define LCD_SDSS          53
-      #define SD_DETECT_PIN     49
-
-    #elif ANY(VIKI2, miniVIKI)
-
-      #define BEEPER_PIN        33
-
-      // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0         44
-      #define DOGLCD_CS         45
-      #define LCD_SCREEN_ROT_180
-
-      #define BTN_EN1           22
-      #define BTN_EN2            7
-      #define BTN_ENC           39
-
-      #define SDSS              53
-      #define SD_DETECT_PIN     -1   // Pin 49 for display sd interface, 72 for easy adapter board
-
-      #define KILL_PIN          31
-
-      #define STAT_LED_RED_PIN  32
-      #define STAT_LED_BLUE_PIN 35
-
-    #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
-
-      #define BTN_EN1           35
-      #define BTN_EN2           37
-      #define BTN_ENC           31
-      #define SD_DETECT_PIN     49
-      #define LCD_SDSS          53
-      #define KILL_PIN          41
-      #define BEEPER_PIN        23
-      #define DOGLCD_CS         29
-      #define DOGLCD_A0         27
-      #define LCD_BACKLIGHT_PIN 33
-
-    #elif ENABLED(MINIPANEL)
-
-      #define BEEPER_PIN        42
-      // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0         44
-      #define DOGLCD_CS         66
-      #define LCD_BACKLIGHT_PIN 65   // backlight LED on A11/D65
-      #define SDSS              53
-
-      #define KILL_PIN          64
-      // GLCD features
-      // Uncomment screen orientation
-      //#define LCD_SCREEN_ROT_90
-      //#define LCD_SCREEN_ROT_180
-      //#define LCD_SCREEN_ROT_270
-      // The encoder and click button
-      #define BTN_EN1           40
-      #define BTN_EN2           63
-      #define BTN_ENC           59
-      // not connected to a pin
-      #define SD_DETECT_PIN     49
-
-    #else
-
-      // Beeper on AUX-4
-      #define BEEPER_PIN        33
-
-      // Buttons directly attached to AUX-2
-      #if ENABLED(REPRAPWORLD_KEYPAD)
-        #define BTN_EN1         64
-        #define BTN_EN2         59
-        #define BTN_ENC         63
-        #define SHIFT_OUT       40
-        #define SHIFT_CLK       44
-        #define SHIFT_LD        42
-      #elif ENABLED(PANEL_ONE)
-        #define BTN_EN1         59   // AUX2 PIN 3
-        #define BTN_EN2         63   // AUX2 PIN 4
-        #define BTN_ENC         49   // AUX3 PIN 7
-      #else
-        #define BTN_EN1         37
-        #define BTN_EN2         35
-        #define BTN_ENC         31
-      #endif
-
-      #if ENABLED(G3D_PANEL)
-        #define SD_DETECT_PIN   49
-        #define KILL_PIN        41
-      #else
-        //#define SD_DETECT_PIN -1   // Ramps doesn't use this
-      #endif
-
-    #endif
-  #endif // NEWPANEL
-
-#endif // HAS_SPI_LCD

Marlin/src/pins/stm32/pins_BLACK_STM32F407VE.h

@@ -1,155 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * STM32F407VET6 with RAMPS-like shield
- * 'Black' STM32F407VET6 board - http://wiki.stm32duino.com/index.php?title=STM32F407
- * Shield - https://github.com/jmz52/Hardware
- */
-
-#if !defined(STM32F4) && !defined(STM32F4xx)
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "Black STM32F4VET6 supports up to 2 hotends / E-steppers."
-#endif
-
-#ifndef BOARD_INFO_NAME
-  #define BOARD_INFO_NAME "Black STM32F4VET6"
-#endif
-
-#define DEFAULT_MACHINE_NAME "STM32F407VET6"
-
-//#define I2C_EEPROM
-//#define E2END 0x1FFF // 8KB
-#define SRAM_EEPROM_EMULATION
-
-//
-// Servos
-//
-#define SERVO0_PIN         PC6
-#define SERVO1_PIN         PC7
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PC13
-#define X_MAX_PIN          PA15
-#define Y_MIN_PIN          PA5
-#define Y_MAX_PIN          PD12
-#define Z_MIN_PIN          PD14
-#define Z_MAX_PIN          PD15
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PC4
-#define X_DIR_PIN          PA4
-#define X_ENABLE_PIN       PE7
-
-#define Y_STEP_PIN         PE5
-#define Y_DIR_PIN          PE2
-#define Y_ENABLE_PIN       PE6
-
-#define Z_STEP_PIN         PD5
-#define Z_DIR_PIN          PD3
-#define Z_ENABLE_PIN       PD6
-
-#define E0_STEP_PIN        PD7
-#define E0_DIR_PIN         PD0
-#define E0_ENABLE_PIN      PB9
-
-#define E1_STEP_PIN        PE0
-#define E1_DIR_PIN         PE1
-#define E1_ENABLE_PIN      PB8
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC0  // T0
-#define TEMP_1_PIN         PC1  // T1
-#define TEMP_BED_PIN       PC2  // TB
-
-#ifndef TEMP_CHAMBER_PIN
-  #define TEMP_CHAMBER_PIN PC3  // TC
-#endif
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PA2  // Heater0
-#define HEATER_1_PIN       PA3  // Heater1
-#define HEATER_BED_PIN     PA1  // Hotbed
-
-#define FAN_PIN            PE9  // Fan0
-#define FAN1_PIN           PE11 // Fan1
-#define FAN2_PIN           PE13 // Fan2
-#define FAN3_PIN           PE14 // Fan3
-
-//
-// Misc. Functions
-//
-#define LED_PIN            PA6
-//#define LED_PIN          PA7
-#define KILL_PIN           PB1
-
-//
-// LCD / Controller
-//
-//#define SD_DETECT_PIN      PC5
-//#define SD_DETECT_PIN      PA8  // SDIO SD_DETECT_PIN, external SDIO card reader only
-
-#define BEEPER_PIN         PD10
-#define LCD_PINS_RS        PE15
-#define LCD_PINS_ENABLE    PD8
-#define LCD_PINS_D4        PE10
-#define LCD_PINS_D5        PE12
-#define LCD_PINS_D6        PD1
-#define LCD_PINS_D7        PE8
-#define BTN_ENC            PD9
-#define BTN_EN1            PD4
-#define BTN_EN2            PD13
-
-#define DOGLCD_CS          LCD_PINS_D5
-#define DOGLCD_A0          LCD_PINS_D6
-
-//
-// Onboard SD support
-//
-#define SDIO_D0_PIN        PC8
-#define SDIO_D1_PIN        PC9
-#define SDIO_D2_PIN        PC10
-#define SDIO_D3_PIN        PC11
-#define SDIO_CK_PIN        PC12
-#define SDIO_CMD_PIN       PD2
-
-#if !defined(SDCARD_CONNECTION) || SDCARD_CONNECTION == ONBOARD
-  #define SDIO_SUPPORT     // Use SDIO for onboard SD
-
-  #ifndef SDIO_SUPPORT
-    #define SOFTWARE_SPI   // Use soft SPI for onboard SD
-    #define SDSS           SDIO_D3_PIN
-    #define SCK_PIN        SDIO_CK_PIN
-    #define MISO_PIN       SDIO_D0_PIN
-    #define MOSI_PIN       SDIO_CMD_PIN
-  #endif
-#endif

Marlin/src/pins/stm32/pins_BTT_GTR_V1_0.h

@@ -1,391 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef TARGET_STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 8 || E_STEPPERS > 8
-  #error "BIGTREE GTR V1.0 supports up to 8 hotends / E-steppers."
-#elif HOTENDS > MAX_EXTRUDERS || E_STEPPERS > MAX_EXTRUDERS
-  #error "Marlin extruder/hotends limit! Increase MAX_EXTRUDERS to continue."
-#endif
-
-#define BOARD_INFO_NAME "BIGTREE GTR 1.0"
-
-// Use one of these or SDCard-based Emulation will be used
-//#define I2C_EEPROM
-//#define SRAM_EEPROM_EMULATION   // Use BackSRAM-based EEPROM emulation
-//#define FLASH_EEPROM_EMULATION  // Use Flash-based EEPROM emulation
-
-#define TP   // Enable to define servo and probe pins
-
-//
-// Servos
-//
-#if ENABLED(TP)
-  #define SERVO0_PIN       PB11
-#endif
-
-#define PS_ON_PIN          PH6
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PF2
-#define X_MAX_PIN          PG14
-#define Y_MIN_PIN          PC13
-#define Y_MAX_PIN          PG9
-#define Z_MIN_PIN          PE0
-#define Z_MAX_PIN          PD3
-
-//
-// Pins on the extender
-//
-//#define X_MIN_PIN        PI4
-//#define X2_MIN_PIN       PF12
-//#define Y_MIN_PIN        PF4
-//#define Y2_MIN_PIN       PI7
-//#define Z_MIN_PIN        PF6
-
-#if ENABLED(TP) && !defined(Z_MIN_PROBE_PIN)
-  #define Z_MIN_PROBE_PIN PH11   // Z Probe must be PH11
-#endif
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PC15
-#define X_DIR_PIN          PF0
-#define X_ENABLE_PIN       PF1
-#ifndef X_CS_PIN
-  #define X_CS_PIN         PC14
-#endif
-
-#define Y_STEP_PIN         PE3
-#define Y_DIR_PIN          PE2
-#define Y_ENABLE_PIN       PE4
-#ifndef Y_CS_PIN
-  #define Y_CS_PIN         PE1
-#endif
-
-#define Z_STEP_PIN         PB8
-#define Z_DIR_PIN          PB7   // PB7
-#define Z_ENABLE_PIN       PB9
-#ifndef Z_CS_PIN
-  #define Z_CS_PIN         PB5
-#endif
-
-#define E0_STEP_PIN        PG12
-#define E0_DIR_PIN         PG11
-#define E0_ENABLE_PIN      PG13
-#ifndef E0_CS_PIN
-  #define E0_CS_PIN        PG10
-#endif
-
-#define E1_STEP_PIN        PD6
-#define E1_DIR_PIN         PD5
-#define E1_ENABLE_PIN      PD7
-#ifndef E1_CS_PIN
-  #define E1_CS_PIN        PD4
-#endif
-
-#define E2_STEP_PIN        PD1
-#define E2_DIR_PIN         PD0
-#define E2_ENABLE_PIN      PD2
-#ifndef E2_CS_PIN
-  #define E2_CS_PIN        PC12
-#endif
-
-#define E3_STEP_PIN        PF3
-#define E3_DIR_PIN         PG3
-#define E3_ENABLE_PIN      PF8
-#ifndef E3_CS_PIN
-  #define E3_CS_PIN        PG4
-#endif
-
-#define E4_STEP_PIN        PD14
-#define E4_DIR_PIN         PD11
-#define E4_ENABLE_PIN      PG2
-#ifndef E4_CS_PIN
-  #define E4_CS_PIN        PE15
-#endif
-
-#define E5_STEP_PIN        PE12
-#define E5_DIR_PIN         PE10
-#define E5_ENABLE_PIN      PF14
-#ifndef E5_CS_PIN
-  #define E5_CS_PIN        PE7
-#endif
-
-#define E6_STEP_PIN        PG0
-#define E6_DIR_PIN         PG1
-#define E6_ENABLE_PIN      PE8
-#ifndef E6_CS_PIN
-  #define E6_CS_PIN        PF15
-#endif
-
-#define E7_STEP_PIN        PH12
-#define E7_DIR_PIN         PH15
-#define E7_ENABLE_PIN      PI0
-#ifndef E7_CS_PIN
-  #define E7_CS_PIN        PH14
-#endif
-
-//
-// Software SPI pins for TMC2130 stepper drivers
-//
-#if ENABLED(TMC_USE_SW_SPI)
-  #ifndef TMC_SW_MOSI
-    #define TMC_SW_MOSI    PG15
-  #endif
-  #ifndef TMC_SW_MISO
-    #define TMC_SW_MISO    PB6
-  #endif
-  #ifndef TMC_SW_SCK
-    #define TMC_SW_SCK     PB3
-  #endif
-#endif
-
-#if HAS_TMC220x
-  /**
-   * TMC2208/TMC2209 stepper drivers
-   *
-   * Hardware serial communication ports.
-   * If undefined software serial is used according to the pins below
-   */
-  //#define X_HARDWARE_SERIAL  Serial
-  //#define X2_HARDWARE_SERIAL Serial1
-  //#define Y_HARDWARE_SERIAL  Serial1
-  //#define Y2_HARDWARE_SERIAL Serial1
-  //#define Z_HARDWARE_SERIAL  Serial1
-  //#define Z2_HARDWARE_SERIAL Serial1
-  //#define E0_HARDWARE_SERIAL Serial1
-  //#define E1_HARDWARE_SERIAL Serial1
-  //#define E2_HARDWARE_SERIAL Serial1
-  //#define E3_HARDWARE_SERIAL Serial1
-  //#define E4_HARDWARE_SERIAL Serial1
-  //#define E5_HARDWARE_SERIAL Serial1
-  //#define E6_HARDWARE_SERIAL Serial1
-  //#define E7_HARDWARE_SERIAL Serial1
-
-  //
-  // Software serial
-  //
-  #define X_SERIAL_TX_PIN  PC14
-  #define X_SERIAL_RX_PIN  PC14
-
-  #define Y_SERIAL_TX_PIN  PE1
-  #define Y_SERIAL_RX_PIN  PE1
-
-  #define Z_SERIAL_TX_PIN  PB5
-  #define Z_SERIAL_RX_PIN  PB5
-
-  #define E0_SERIAL_TX_PIN PG10
-  #define E0_SERIAL_RX_PIN PG10
-
-  #define E1_SERIAL_TX_PIN PD4
-  #define E1_SERIAL_RX_PIN PD4
-
-  #define E2_SERIAL_TX_PIN PC12
-  #define E2_SERIAL_RX_PIN PC12
-
-  #define E3_SERIAL_TX_PIN PG4
-  #define E3_SERIAL_RX_PIN PG4
-
-  #define E4_SERIAL_TX_PIN PE15
-  #define E4_SERIAL_RX_PIN PE15
-
-  #define E5_SERIAL_TX_PIN PE7
-  #define E5_SERIAL_RX_PIN PE7
-
-  #define E6_SERIAL_TX_PIN PF15
-  #define E6_SERIAL_RX_PIN PF15
-
-  #define E7_SERIAL_TX_PIN PH14
-  #define E7_SERIAL_RX_PIN PH14
-
-  // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // T1 <-> E0
-#define TEMP_1_PIN         PC2   // T2 <-> E1
-#define TEMP_2_PIN         PC3   // T3 <-> E2
-
-#define TEMP_3_PIN         PA3   // T4 <-> E3
-#define TEMP_4_PIN         PF9   // T5 <-> E4
-#define TEMP_5_PIN         PF10  // T6 <-> E5
-#define TEMP_6_PIN         PF7   // T7 <-> E6
-#define TEMP_7_PIN         PF5   // T8 <-> E7
-
-#define TEMP_BED_PIN       PC0   // T0 <-> Bed
-
-// SPI for Max6675 or Max31855 Thermocouple
-// Uses a separate SPI bus
-// If you have a two-way thermocouple, you can customize two THERMO_CSx_PIN pins (x:1~2)
-
-#define THERMO_SCK_PIN     PI1   // SCK
-#define THERMO_DO_PIN      PI2   // MISO
-#define THERMO_CS1_PIN     PH9   // CS1
-#define THERMO_CS2_PIN     PH2   // CS2
-
-#define MAX6675_SS_PIN     THERMO_CS1_PIN
-#define MAX6675_SS2_PIN    THERMO_CS2_PIN
-#define MAX6675_SCK_PIN    THERMO_SCK_PIN
-#define MAX6675_DO_PIN     THERMO_DO_PIN
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PB1   // Heater0
-#define HEATER_1_PIN       PA1   // Heater1
-#define HEATER_2_PIN       PB0   // Heater2
-
-#define HEATER_3_PIN       PD15  // Heater3
-#define HEATER_4_PIN       PD13  // Heater4
-#define HEATER_5_PIN       PD12  // Heater5
-#define HEATER_6_PIN       PE13 // Heater6
-#define HEATER_7_PIN       PI6  // Heater7
-
-#define HEATER_BED_PIN     PA2   // Hotbed
-
-#define FAN_PIN            PE5   // Fan0
-#define FAN1_PIN           PE6   // Fan1
-#define FAN2_PIN           PC8   // Fan2
-
-#define FAN3_PIN           PI5   // Fan3
-#define FAN4_PIN           PE9   // Fan4
-#define FAN5_PIN           PE11  // Fan5
-//#define FAN6_PIN           PC9   // Fan6
-//#define FAN7_PIN           PE14  // Fan7
-
-//
-// By default the onboard SD (SPI1) is enabled
-//
-#define CUSTOM_SPI_PINS
-#if DISABLED(CUSTOM_SPI_PINS)
-  #define SDSS             PB12
-#endif
-
-// HAL SPI1 pins group
-#if ENABLED(CUSTOM_SPI_PINS)
-  #define SDSS             PA4
-  #define SD_DETECT_PIN    PC4
-  #define LCD_SDSS         PA4
-
-  #define SCK_PIN          PA5
-  #define MISO_PIN         PA6
-  #define MOSI_PIN         PA7
-  #define SS_PIN           PA4   // Chip select for SD card used by Marlin
-#endif
-
-/**
- *               _____                                             _____
- *           NC | · · | GND                                    5V | · · | GND
- *        RESET | · · | PB10(SD_DETECT)             (LCD_D7)  PG5 | · · | PG6  (LCD_D6)
- *   (MOSI)PB15 | · · | PH10(BTN_EN2)               (LCD_D5)  PG7 | · · | PG8  (LCD_D4)
- *  (SD_SS)PB12 | · · | PD10(BTN_EN1)               (LCD_RS)  PA8 | · · | PC10 (LCD_EN)
- *    (SCK)PB13 | · · | PB14(MISO)                 (BTN_ENC) PA15 | · · | PC11  (BEEPER)
- *               ￣￣                                               ￣￣
- *               EXP2                                              EXP1
- */
-
-//
-// LCDs and Controllers
-//
-#if HAS_SPI_LCD
-  #define BEEPER_PIN       PC11
-  #define BTN_ENC          PA15
-
-  #if ENABLED(CR10_STOCKDISPLAY)
-
-    #define LCD_PINS_RS    PA8
-
-    #define BTN_EN1        PD10
-    #define BTN_EN2        PH10
-
-    #define LCD_PINS_ENABLE PG7
-    #define LCD_PINS_D4    PG8
-
-    //#undef ST7920_DELAY_1
-    //#undef ST7920_DELAY_2
-    //#undef ST7920_DELAY_3
-
-  #else
-
-    #define LCD_PINS_RS    PA8
-
-    #define BTN_EN1        PD10
-    #define BTN_EN2        PH10
-
-    #if DISABLED(CUSTOM_SPI_PINS)
-      #define SD_DETECT_PIN PB10
-      #define LCD_SDSS     PB12
-    #endif
-
-    #define LCD_PINS_ENABLE PC10
-    #define LCD_PINS_D4    PG8
-
-    #if ENABLED(FYSETC_MINI_12864)
-      #define DOGLCD_CS    PC10
-      #define DOGLCD_A0    PA8
-      //#define LCD_BACKLIGHT_PIN -1
-      #define LCD_RESET_PIN PG8   // Must be high or open for LCD to operate normally.
-      #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
-        #ifndef RGB_LED_R_PIN
-          #define RGB_LED_R_PIN PG7
-        #endif
-        #ifndef RGB_LED_G_PIN
-          #define RGB_LED_G_PIN PG6
-        #endif
-        #ifndef RGB_LED_B_PIN
-          #define RGB_LED_B_PIN PG5
-        #endif
-      #elif ENABLED(FYSETC_MINI_12864_2_1)
-        #define NEOPIXEL_PIN    PF13
-      #endif
-    #endif // !FYSETC_MINI_12864
-
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  PG7
-      #define LCD_PINS_D6  PG6
-      #define LCD_PINS_D7  PG5
-    #endif
-
-  #endif
-
-  // Alter timing for graphical display
-  #if HAS_GRAPHICAL_LCD
-    #define BOARD_ST7920_DELAY_1 DELAY_NS(96)
-    #define BOARD_ST7920_DELAY_2 DELAY_NS(48)
-    #define BOARD_ST7920_DELAY_3 DELAY_NS(600)
-  #endif
-
-  //#define DOGLCD_CS      PB12
-  //#define DOGLCD_A0      PA8
-  //#define LCD_PINS_DC    PB14
-  //#define DOGLCD_MOSI    PB15
-
-#endif // HAS_SPI_LCD

Marlin/src/pins/stm32/pins_BTT_SKR_MINI_E3.h

@@ -1,191 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef TARGET_STM32F1
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#endif
-
-// Release PB3/PB4 (E0 STP/DIR) from JTAG pins
-#define DISABLE_JTAG
-
-// Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
-#define FLASH_EEPROM_EMULATION
-#define EEPROM_PAGE_SIZE     uint16(0x800) // 2KB
-#define EEPROM_START_ADDRESS uint32(0x8000000 + (STM32_FLASH_SIZE) * 1024 - 2 * EEPROM_PAGE_SIZE)
-#undef E2END
-#define E2END                (EEPROM_PAGE_SIZE - 1) // 2KB
-
-//
-// Servos
-//
-#define SERVO0_PIN         PA1
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PC0
-#define Y_STOP_PIN         PC1
-#define Z_STOP_PIN         PC2
-
-//
-// Z Probe must be this pins
-//
-#define Z_MIN_PROBE_PIN    PC14
-
-//
-// Filament Runout Sensor
-//
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN   PC15   // "E0-STOP"
-#endif
-
-//
-// Steppers
-//
-#define X_ENABLE_PIN       PB14
-#define X_STEP_PIN         PB13
-#define X_DIR_PIN          PB12
-
-#define Y_ENABLE_PIN       PB11
-#define Y_STEP_PIN         PB10
-#define Y_DIR_PIN          PB2
-
-#define Z_ENABLE_PIN       PB1
-#define Z_STEP_PIN         PB0
-#define Z_DIR_PIN          PC5
-
-#define E0_ENABLE_PIN      PD2
-#define E0_STEP_PIN        PB3
-#define E0_DIR_PIN         PB4
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PA0   // Analog Input
-#define TEMP_BED_PIN       PC3   // Analog Input
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PC8   // EXTRUDER
-#define HEATER_BED_PIN     PC9   // BED
-#define FAN_PIN            PA8
-
-//
-// USB connect control
-//
-#define USB_CONNECT_PIN    PC13
-#define USB_CONNECT_INVERTING false
-
-#define SD_DETECT_PIN      PC4
-
-/**
- *                 _____
- *             5V | 1 2 | GND
- *  (LCD_EN) PB7  | 3 4 | PB8  (LCD_RS)
- *  (LCD_D4) PB9  | 5 6   PA10 (BTN_EN2)
- *          RESET | 7 8 | PA9  (BTN_EN1)
- * (BTN_ENC) PB6  | 9 10| PB5  (BEEPER)
- *                 -----
- *                 EXP1
- */
-
-#define EXPA1_03_PIN       PB7
-#define EXPA1_04_PIN       PB8
-#define EXPA1_05_PIN       PB9
-#define EXPA1_06_PIN       PA10
-#define EXPA1_07_PIN       -1
-#define EXPA1_08_PIN       PA9
-#define EXPA1_09_PIN       PB6
-#define EXPA1_10_PIN       PB5
-
-#if HAS_SPI_LCD
-
-  #if ENABLED(CR10_STOCKDISPLAY)
-
-    #define BEEPER_PIN     EXPA1_10_PIN
-
-    #define BTN_EN1        EXPA1_08_PIN
-    #define BTN_EN2        EXPA1_06_PIN
-    #define BTN_ENC        EXPA1_09_PIN
-
-    #define LCD_PINS_RS    EXPA1_04_PIN
-    #define LCD_PINS_ENABLE EXPA1_03_PIN
-    #define LCD_PINS_D4    EXPA1_05_PIN
-
-  #elif ENABLED(ZONESTAR_LCD)     // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD!
-
-    #error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_SKR_MINI_E3.h' for details. Comment out this line to continue."
-
-    #define LCD_PINS_RS    EXPA1_05_PIN
-    #define LCD_PINS_ENABLE EXPA1_09_PIN
-    #define LCD_PINS_D4    EXPA1_04_PIN
-    #define LCD_PINS_D5    EXPA1_06_PIN
-    #define LCD_PINS_D6    EXPA1_08_PIN
-    #define LCD_PINS_D7    EXPA1_10_PIN
-    #define ADC_KEYPAD_PIN PA1    // Repurpose servo pin for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD!
-
-  #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
-
-    /** Creality Ender-2 display pinout
-     *                   _____
-     *               5V | 1 2 | GND
-     *      (MOSI) PB7  | 3 4 | PB8  (LCD_RS)
-     *    (LCD_A0) PB9  | 5 6   PA10 (BTN_EN2)
-     *            RESET | 7 8 | PA9  (BTN_EN1)
-     *   (BTN_ENC) PB6  | 9 10| PB5  (SCK)
-     *                   -----
-     *                    EXP1
-     */
-    #define BTN_EN1        EXPA1_08_PIN
-    #define BTN_EN2        EXPA1_06_PIN
-    #define BTN_ENC        EXPA1_09_PIN
-
-    #define DOGLCD_CS      EXPA1_04_PIN
-    #define DOGLCD_A0      EXPA1_05_PIN
-    #define DOGLCD_SCK     EXPA1_10_PIN
-    #define DOGLCD_MOSI    EXPA1_03_PIN
-    #define FORCE_SOFT_SPI
-    #define LCD_BACKLIGHT_PIN -1
-
-  #else
-
-    #error "Only ZONESTAR_LCD, MKS_MINI_12864, ENDER2_STOCKDISPLAY, and CR10_STOCKDISPLAY are currently supported on the BIGTREE_SKR_MINI_E3."
-
-  #endif
-
-#endif // HAS_SPI_LCD
-
-//
-// SD Support
-//
-#define HAS_ONBOARD_SD
-
-#ifndef SDCARD_CONNECTION
-  #define SDCARD_CONNECTION ONBOARD
-#endif
-
-#define ON_BOARD_SPI_DEVICE 1    // SPI1
-#define ONBOARD_SD_CS_PIN  PA4   // Chip select for "System" SD card

Marlin/src/pins/stm32/pins_BTT_SKR_PRO_V1_1.h

@@ -1,286 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef TARGET_STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 3 || E_STEPPERS > 3
-  #error "BIGTREE SKR Pro V1.1 supports up to 3 hotends / E-steppers."
-#endif
-
-#define BOARD_INFO_NAME "BIGTREE SKR Pro 1.1" // redefined?
-
-// Use one of these or SDCard-based Emulation will be used
-//#define SRAM_EEPROM_EMULATION   // Use BackSRAM-based EEPROM emulation
-//#define FLASH_EEPROM_EMULATION  // Use Flash-based EEPROM emulation
-
-//
-// Servos
-//
-#define SERVO0_PIN         PA1
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PB10
-#define X_MAX_PIN          PE15
-#define Y_MIN_PIN          PE12
-#define Y_MAX_PIN          PE10
-#define Z_MIN_PIN          PG8
-#define Z_MAX_PIN          PG5
-
-//
-// Z Probe must be this pins
-//
-#ifndef Z_MIN_PROBE_PIN
-  #define Z_MIN_PROBE_PIN  PA2
-#endif
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PE9
-#define X_DIR_PIN          PF1
-#define X_ENABLE_PIN       PF2
-#ifndef X_CS_PIN
-  #define X_CS_PIN         PA15
-#endif
-
-#define Y_STEP_PIN         PE11
-#define Y_DIR_PIN          PE8
-#define Y_ENABLE_PIN       PD7
- #ifndef Y_CS_PIN
-  #define Y_CS_PIN         PB8
-#endif
-
-#define Z_STEP_PIN         PE13
-#define Z_DIR_PIN          PC2
-#define Z_ENABLE_PIN       PC0
-#ifndef Z_CS_PIN
-  #define Z_CS_PIN         PB9
-#endif
-
-#define E0_STEP_PIN        PE14
-#define E0_DIR_PIN         PA0
-#define E0_ENABLE_PIN      PC3
-#ifndef E0_CS_PIN
-  #define E0_CS_PIN        PB3
-#endif
-
-#define E1_STEP_PIN        PD15
-#define E1_DIR_PIN         PE7
-#define E1_ENABLE_PIN      PA3
-#ifndef E1_CS_PIN
-  #define E1_CS_PIN        PG15
-#endif
-
-#define E2_STEP_PIN        PD13
-#define E2_DIR_PIN         PG9
-#define E2_ENABLE_PIN      PF0
-#ifndef E2_CS_PIN
-  #define E2_CS_PIN        PG12
-#endif
-
-//
-// Software SPI pins for TMC2130 stepper drivers
-//
-#if ENABLED(TMC_USE_SW_SPI)
-  #ifndef TMC_SW_MOSI
-    #define TMC_SW_MOSI    PC12
-  #endif
-  #ifndef TMC_SW_MISO
-    #define TMC_SW_MISO    PC11
-  #endif
-  #ifndef TMC_SW_SCK
-    #define TMC_SW_SCK     PC10
-  #endif
-#endif
-
-#if HAS_TMC220x
-  /**
-   * TMC2208/TMC2209 stepper drivers
-   *
-   * Hardware serial communication ports.
-   * If undefined software serial is used according to the pins below
-   */
-  //#define X_HARDWARE_SERIAL  Serial
-  //#define X2_HARDWARE_SERIAL Serial1
-  //#define Y_HARDWARE_SERIAL  Serial1
-  //#define Y2_HARDWARE_SERIAL Serial1
-  //#define Z_HARDWARE_SERIAL  Serial1
-  //#define Z2_HARDWARE_SERIAL Serial1
-  //#define E0_HARDWARE_SERIAL Serial1
-  //#define E1_HARDWARE_SERIAL Serial1
-  //#define E2_HARDWARE_SERIAL Serial1
-  //#define E3_HARDWARE_SERIAL Serial1
-  //#define E4_HARDWARE_SERIAL Serial1
-
-  //
-  // Software serial
-  //
-  #define X_SERIAL_TX_PIN  PC13
-  #define X_SERIAL_RX_PIN  PC13
-
-  #define Y_SERIAL_TX_PIN  PE3
-  #define Y_SERIAL_RX_PIN  PE3
-
-  #define Z_SERIAL_TX_PIN  PE1
-  #define Z_SERIAL_RX_PIN  PE1
-
-  #define E0_SERIAL_TX_PIN PD4
-  #define E0_SERIAL_RX_PIN PD4
-
-  #define E1_SERIAL_TX_PIN PD1
-  #define E1_SERIAL_RX_PIN PD1
-
-  #define E2_SERIAL_TX_PIN PD6
-  #define E2_SERIAL_RX_PIN PD6
-
-  // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PF4  // T1 <-> E0
-#define TEMP_1_PIN         PF5  // T2 <-> E1
-#define TEMP_2_PIN         PF6  // T3 <-> E2
-#define TEMP_BED_PIN       PF3  // T0 <-> Bed
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PB1  // Heater0
-#define HEATER_1_PIN       PD14 // Heater1
-#define HEATER_2_PIN       PB0  // Heater1
-#define HEATER_BED_PIN     PD12 // Hotbed
-#define FAN_PIN            PC8  // Fan0
-#define FAN1_PIN           PE5  // Fan1
-#define FAN2_PIN           PE6  // Fan2
-
-//
-// Misc. Functions
-//
-
-#ifndef SDCARD_CONNECTION
-  #define SDCARD_CONNECTION LCD
-#endif
-
-//
-// Onboard SD card
-//   NOT compatible with LCD
-//
-#if SDCARD_CONNECTION == ONBOARD && !HAS_SPI_LCD
-  #define SOFTWARE_SPI            // Use soft SPI for onboard SD
-  #define SDSS             PA4
-  #define SCK_PIN          PA5
-  #define MISO_PIN         PA6
-  #define MOSI_PIN         PB5
-#else
-  #define SDSS             PB12
-#endif
-
-
-/**
- *               _____                                             _____
- *           NC | · · | GND                                    5V | · · | GND
- *        RESET | · · | PF12(SD_DETECT)             (LCD_D7)  PG7 | · · | PG6  (LCD_D6)
- *   (MOSI)PB15 | · · | PF11(BTN_EN2)               (LCD_D5)  PG3 | · · | PG2  (LCD_D4)
- *  (SD_SS)PB12 | · · | PG10(BTN_EN1)               (LCD_RS) PD10 | · · | PD11 (LCD_EN)
- *    (SCK)PB13 | · · | PB14(MISO)                 (BTN_ENC)  PA8 | · · | PG4  (BEEPER)
- *               ￣￣                                               ￣￣
- *               EXP2                                              EXP1
- */
-
-//
-// LCDs and Controllers
-//
-#if HAS_SPI_LCD
-  #define BEEPER_PIN       PG4
-  #define BTN_ENC          PA8
-
-  #if ENABLED(CR10_STOCKDISPLAY)
-    #define LCD_PINS_RS    PG6
-
-    #define BTN_EN1        PD11
-    #define BTN_EN2        PG2
-
-    #define LCD_PINS_ENABLE PG7
-    #define LCD_PINS_D4    PG3
-
-    // CR10_Stock Display needs a different delay setting on SKR PRO v1.1, so undef it here.
-    // It will be defined again at the #HAS_GRAPHICAL_LCD section below.
-    #undef ST7920_DELAY_1
-    #undef ST7920_DELAY_2
-    #undef ST7920_DELAY_3
-
-
-  #else
-
-    #define LCD_PINS_RS    PD10
-
-    #define BTN_EN1        PG10
-    #define BTN_EN2        PF11
-    #define SD_DETECT_PIN  PF12
-
-    #define LCD_SDSS       PB12
-
-    #define LCD_PINS_ENABLE PD11
-    #define LCD_PINS_D4    PG2
-
-    #if ENABLED(FYSETC_MINI_12864)
-      #define DOGLCD_CS    PD11
-      #define DOGLCD_A0    PD10
-      //#define LCD_BACKLIGHT_PIN -1
-      #define LCD_RESET_PIN PG2   // Must be high or open for LCD to operate normally.
-      #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
-        #ifndef RGB_LED_R_PIN
-          #define RGB_LED_R_PIN PG3
-        #endif
-        #ifndef RGB_LED_G_PIN
-          #define RGB_LED_G_PIN PG6
-        #endif
-        #ifndef RGB_LED_B_PIN
-          #define RGB_LED_B_PIN PG7
-        #endif
-      #elif ENABLED(FYSETC_MINI_12864_2_1)
-        #define NEOPIXEL_PIN    PG3
-      #endif
-    #endif // !FYSETC_MINI_12864
-
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  PG3
-      #define LCD_PINS_D6  PG6
-      #define LCD_PINS_D7  PG7
-    #endif
-
-  #endif
-
-  // Alter timing for graphical display
-  #if HAS_GRAPHICAL_LCD
-    #define BOARD_ST7920_DELAY_1 DELAY_NS(96)
-    #define BOARD_ST7920_DELAY_2 DELAY_NS(48)
-    #define BOARD_ST7920_DELAY_3 DELAY_NS(600)
-  #endif
-
-#endif // HAS_SPI_LCD

Marlin/src/pins/stm32/pins_CHITU3D.h

@@ -1,283 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#if !defined(__STM32F1__) && !defined(__STM32F4__)
-  #error "Oops! Select an STM32F1/4 board in 'Tools > Board.'"
-#endif
-
-/**
- * 2017 Victor Perez Marlin for stm32f1 test
- */
-
-#define BOARD_INFO_NAME      "Chitu3D"
-#define DEFAULT_MACHINE_NAME "STM32F103RET6"
-
-// Enable I2C_EEPROM for testing
-//#define I2C_EEPROM
-
-// Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PE5
-#define X_DIR_PIN          PE6
-#define X_ENABLE_PIN       PC13
-#define X_MIN_PIN          PG10
-#define X_MAX_PIN          -1
-
-#define Y_STEP_PIN         PE2
-#define Y_DIR_PIN          PE3
-#define Y_ENABLE_PIN       PE4
-#define Y_MIN_PIN          PA12
-#define Y_MAX_PIN
-
-#define Z_STEP_PIN         PB9
-#define Z_DIR_PIN          PE0
-#define Z_ENABLE_PIN       PE1
-#define Z_MIN_PIN          PA14
-#define Z_MAX_PIN          -1
-
-#define Y2_STEP_PIN        -1
-#define Y2_DIR_PIN         -1
-#define Y2_ENABLE_PIN      -1
-
-#define Z2_STEP_PIN        -1
-#define Z2_DIR_PIN         -1
-#define Z2_ENABLE_PIN      -1
-
-#define E0_STEP_PIN        PB4
-#define E0_DIR_PIN         PB5
-#define E0_ENABLE_PIN      PB8
-
-
-
-#define E1_STEP_PIN        -1
-#define E1_DIR_PIN         -1
-#define E1_ENABLE_PIN      -1
-
-#define E2_STEP_PIN        -1
-#define E2_DIR_PIN         -1
-#define E2_ENABLE_PIN      -1
-
-//
-// Misc. Functions
-//
-#define SDSS               -1
-#define LED_PIN            -1
-#define CASE_LIGHT_PIN      8
-
-#define PS_ON_PIN          -1
-#define KILL_PIN           PD6      // LED strip 24v
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PD12     // HOT-END
-#define HEATER_1_PIN       -1
-#define HEATER_2_PIN       -1
-
-#define HEATER_BED_PIN     PG11     // HOT-BED
-#define HEATER_BED2_PIN    -1       // BED2
-#define HEATER_BED3_PIN    -1       // BED3
-
-#ifndef FAN_PIN
-  #define FAN_PIN          PG14     // MAIN BOARD FAN
-#endif
-
-#define FAN_SOFT_PWM
-
-//
-// Temperature Sensors
-//
-#define TEMP_BED_PIN       PA0   // Analog Input
-#define TEMP_0_PIN         PA1   // Analog Input
-#define TEMP_1_PIN         -1   // Analog Input
-#define TEMP_2_PIN         -1   // Analog Input
-
-//
-// LCD Pins
-//
-#if HAS_SPI_LCD
-
-  #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define LCD_PINS_RS         49   // CS chip select /SS chip slave select
-    #define LCD_PINS_ENABLE     51   // SID (MOSI)
-    #define LCD_PINS_D4         52   // SCK (CLK) clock
-  #elif BOTH(NEWPANEL, PANEL_ONE)
-    #define LCD_PINS_RS         PB8
-    #define LCD_PINS_ENABLE     PD2
-    #define LCD_PINS_D4         PB12
-    #define LCD_PINS_D5         PB13
-    #define LCD_PINS_D6         PB14
-    #define LCD_PINS_D7         PB15
-  #else
-    #define LCD_PINS_RS         PB8
-    #define LCD_PINS_ENABLE     PD2
-    #define LCD_PINS_D4         PB12
-    #define LCD_PINS_D5         PB13
-    #define LCD_PINS_D6         PB14
-    #define LCD_PINS_D7         PB15
-    #if DISABLED(NEWPANEL)
-      #define BEEPER_PIN        33
-      // Buttons attached to a shift register
-      // Not wired yet
-      //#define SHIFT_CLK       38
-      //#define SHIFT_LD        42
-      //#define SHIFT_OUT       40
-      //#define SHIFT_EN        17
-    #endif
-  #endif
-
-  #if ENABLED(NEWPANEL)
-
-    #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
-
-      #define BEEPER_PIN        37
-
-      #define BTN_EN1           31
-      #define BTN_EN2           33
-      #define BTN_ENC           35
-
-      #define SD_DETECT_PIN     49
-      #define KILL_PIN          41
-
-      #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-        #define LCD_BACKLIGHT_PIN 39
-      #endif
-
-    #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-
-      #define BTN_EN1           64
-      #define BTN_EN2           59
-      #define BTN_ENC           63
-      #define SD_DETECT_PIN     42
-
-    #elif ENABLED(LCD_I2C_PANELOLU2)
-
-      #define BTN_EN1           47
-      #define BTN_EN2           43
-      #define BTN_ENC           32
-      #define LCD_SDSS          53
-      #define SD_DETECT_PIN     -1
-      #define KILL_PIN          41
-
-    #elif ENABLED(LCD_I2C_VIKI)
-
-      #define BTN_EN1           22   // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
-      #define BTN_EN2            7   // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
-
-      #define BTN_ENC           -1
-      #define LCD_SDSS          53
-      #define SD_DETECT_PIN     49
-
-    #elif ANY(VIKI2, miniVIKI)
-
-      #define BEEPER_PIN        33
-
-      // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0         44
-      #define DOGLCD_CS         45
-      #define LCD_SCREEN_ROT_180
-
-      #define BTN_EN1           22
-      #define BTN_EN2            7
-      #define BTN_ENC           39
-
-      #define SDSS              53
-      #define SD_DETECT_PIN     -1   // Pin 49 for display sd interface, 72 for easy adapter board
-
-      #define KILL_PIN          31
-
-      #define STAT_LED_RED_PIN  32
-      #define STAT_LED_BLUE_PIN 35
-
-    #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
-      #define BTN_EN1           35
-      #define BTN_EN2           37
-      #define BTN_ENC           31
-      #define SD_DETECT_PIN     49
-      #define LCD_SDSS          53
-      #define KILL_PIN          41
-      #define BEEPER_PIN        23
-      #define DOGLCD_CS         29
-      #define DOGLCD_A0         27
-      #define LCD_BACKLIGHT_PIN 33
-
-    #elif ENABLED(MINIPANEL)
-
-      #define BEEPER_PIN        42
-      // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0         44
-      #define DOGLCD_CS         66
-      #define LCD_BACKLIGHT_PIN 65   // backlight LED on A11/D65
-      #define SDSS              53
-
-      #define KILL_PIN          64
-      // GLCD features
-      // Uncomment screen orientation
-      //#define LCD_SCREEN_ROT_90
-      //#define LCD_SCREEN_ROT_180
-      //#define LCD_SCREEN_ROT_270
-      // The encoder and click button
-      #define BTN_EN1           40
-      #define BTN_EN2           63
-      #define BTN_ENC           59
-      // not connected to a pin
-      #define SD_DETECT_PIN     49
-
-    #else
-
-      // Beeper on AUX-4
-      #define BEEPER_PIN        33
-
-      // Buttons directly attached to AUX-2
-      #if ENABLED(REPRAPWORLD_KEYPAD)
-        #define BTN_EN1         64
-        #define BTN_EN2         59
-        #define BTN_ENC         63
-        #define SHIFT_OUT       40
-        #define SHIFT_CLK       44
-        #define SHIFT_LD        42
-      #elif ENABLED(PANEL_ONE)
-        #define BTN_EN1         59   // AUX2 PIN 3
-        #define BTN_EN2         63   // AUX2 PIN 4
-        #define BTN_ENC         49   // AUX3 PIN 7
-      #else
-        #define BTN_EN1         37
-        #define BTN_EN2         35
-        #define BTN_ENC         31
-      #endif
-
-      #if ENABLED(G3D_PANEL)
-        #define SD_DETECT_PIN   49
-        #define KILL_PIN        41
-      #else
-        //#define SD_DETECT_PIN -1   // Ramps doesn't use this
-      #endif
-
-    #endif
-  #endif // NEWPANEL
-
-#endif // HAS_SPI_LCD

Marlin/src/pins/stm32/pins_FLYF407ZG.h

@@ -1,266 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#if !defined(STM32F4) && !defined(STM32F4xx)
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 6 || E_STEPPERS > 6
-  #error "FLYF407ZG supports up to 6 hotends / E-steppers."
-#endif
-
-#define BOARD_INFO_NAME      "FLYF407ZG"
-#define BOARD_WEBSITE_URL    "github.com/FLYmaker/FLYF407ZG"
-#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
-
-#undef E2END
-#define E2END 0xFFF // 4KB
-
-//
-// Servos
-//
-#define SERVO0_PIN         PE11
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PC3
-#define X_MAX_PIN          PC2
-#define Y_MIN_PIN          PF2
-#define Y_MAX_PIN          PF1
-#define Z_MIN_PIN          PF0
-#define Z_MAX_PIN          PC15
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-#define Z_MIN_PROBE_PIN    PC14   // Z3_PIN
-
-//
-// Steppers
-//
-
-#define X_STEP_PIN         PB9
-#define X_DIR_PIN          PE0
-#define X_ENABLE_PIN       PE1
-#ifndef X_CS_PIN
-  #define X_CS_PIN         PG13
-#endif
-
-#define Y_STEP_PIN         PB8
-#define Y_DIR_PIN          PG11
-#define Y_ENABLE_PIN       PG12
-#ifndef Y_CS_PIN
-  #define Y_CS_PIN         PG10
-#endif
-
-#define Z_STEP_PIN         PA8
-#define Z_DIR_PIN          PD6
-#define Z_ENABLE_PIN       PD7
-#ifndef Z_CS_PIN
-  #define Z_CS_PIN         PD5
-#endif
-
-#define E0_STEP_PIN        PC7
-#define E0_DIR_PIN         PD3
-#define E0_ENABLE_PIN      PD4
-#ifndef E0_CS_PIN
-  #define E0_CS_PIN        PD1
-#endif
-
-#define E1_STEP_PIN        PC6
-#define E1_DIR_PIN         PA15
-#define E1_ENABLE_PIN      PD0
-#ifndef E1_CS_PIN
-  #define E1_CS_PIN        PA14
-#endif
-
-#define E2_STEP_PIN        PD15
-#define E2_DIR_PIN         PG7
-#define E2_ENABLE_PIN      PG8
-#ifndef E2_CS_PIN
-  #define E2_CS_PIN        PG6
-#endif
-
-#define E3_STEP_PIN        PD14
-#define E3_DIR_PIN         PG4
-#define E3_ENABLE_PIN      PG5
-#ifndef E3_CS_PIN
-  #define E3_CS_PIN        PG3
-#endif
-
-#define E4_STEP_PIN        PD13
-#define E4_DIR_PIN         PD11
-#define E4_ENABLE_PIN      PG2
-#ifndef E4_CS_PIN
-  #define E4_CS_PIN        PD10
-#endif
-
-#define E5_STEP_PIN        PD12
-#define E5_DIR_PIN         PD8
-#define E5_ENABLE_PIN      PD9
-#ifndef E5_CS_PIN
-  #define E5_CS_PIN        PB12
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PA0   // Analog Input
-#define TEMP_1_PIN         PC1   // Analog Input
-#define TEMP_2_PIN         PC0   // Analog Input
-#define TEMP_3_PIN         PF10  // Analog Input
-#define TEMP_4_PIN         PF5   // Analog Input
-#define TEMP_5_PIN         PF4   // Analog Input
-#define TEMP_BED_PIN       PF3   // Analog Input
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PF7
-#define HEATER_1_PIN       PF6
-#define HEATER_2_PIN       PE6
-#define HEATER_3_PIN       PE5
-#define HEATER_4_PIN       PE4
-#define HEATER_5_PIN       PA2
-#define HEATER_BED_PIN     PE2
-
-#ifndef FAN_PIN
-  #define FAN_PIN          PF8
-#endif
-#define FAN1_PIN           PF9
-#define FAN2_PIN           PE3
-#define FAN3_PIN           PA1
-#define FAN4_PIN           PE13
-#define FAN5_PIN           PB11
-
-//
-// Onboard SD support
-//
-
-#define SDIO_D0_PIN        PC8
-#define SDIO_D1_PIN        PC9
-//#define SD_CARD_DETECT_PIN PC13
-#define SDIO_D2_PIN        PC10
-#define SDIO_D3_PIN        PC11
-#define SDIO_CK_PIN        PC12
-#define SDIO_CMD_PIN       PD2
-
-#if !defined(SDCARD_CONNECTION) || SDCARD_CONNECTION == ONBOARD
-  #define SDIO_SUPPORT     // Use SDIO for onboard SD
-
-  #ifndef SDIO_SUPPORT
-    #define SOFTWARE_SPI   // Use soft SPI for onboard SD
-    #define SDSS           SDIO_D3_PIN
-    #define SCK_PIN        SDIO_CK_PIN
-    #define MISO_PIN       SDIO_D0_PIN
-    #define MOSI_PIN       SDIO_CMD_PIN
-  #endif
-#endif
-
-//
-// Trinamic Software SPI
-//
-
-#if ENABLED(TMC_USE_SW_SPI)
-  #ifndef TMC_SW_MOSI
-    #define TMC_SW_MOSI    PB15
-  #endif
-  #ifndef TMC_SW_MISO
-    #define TMC_SW_MISO    PB14
-  #endif
-  #ifndef TMC_SW_SCK
-    #define TMC_SW_SCK     PB13
-  #endif
-#endif
-
-//
-// Trinamic Software Serial
-//
-
-#if HAS_TMC220x
-  #define X_SERIAL_TX_PIN  PG13
-  #define X_SERIAL_RX_PIN  PG13
-
-  #define Y_SERIAL_TX_PIN  PG10
-  #define Y_SERIAL_RX_PIN  PG10
-
-  #define Z_SERIAL_TX_PIN  PD5
-  #define Z_SERIAL_RX_PIN  PD5
-
-  #define E0_SERIAL_TX_PIN PD1
-  #define E0_SERIAL_RX_PIN PD1
-
-  #define E1_SERIAL_TX_PIN PA14
-  #define E1_SERIAL_RX_PIN PA14
-
-  #define E2_SERIAL_TX_PIN PG6
-  #define E2_SERIAL_RX_PIN PG6
-
-  #define E3_SERIAL_TX_PIN PG3
-  #define E3_SERIAL_RX_PIN PG3
-
-  #define E4_SERIAL_TX_PIN PD10
-  #define E4_SERIAL_RX_PIN PD10
-
-  #define E5_SERIAL_TX_PIN PB12
-  #define E5_SERIAL_RX_PIN PB12
-
-#endif
-
-
-//
-// LCD / Controller
-//
-#define SCK_PIN            PB13
-#define MISO_PIN           PB14
-#define MOSI_PIN           PB15
-#define SDSS               PF11
-#define SD_DETECT_PIN      PB2
-#define BEEPER_PIN         PB10
-#define LCD_PINS_RS        PE12
-#define LCD_PINS_ENABLE    PE14
-#define LCD_PINS_D4        PE10
-#define LCD_PINS_D5        PE9
-#define LCD_PINS_D6        PE8
-#define LCD_PINS_D7        PE7
-#define BTN_EN1            PC4
-#define BTN_EN2            PC5
-#define BTN_ENC            PE15
-
-//
-// Filament runout
-//
-
-#define FIL_RUNOUT_PIN     PA3
-
-//
-// ST7920 Delays
-//
-#ifndef ST7920_DELAY_1
-  #define ST7920_DELAY_1 DELAY_NS(96)
-#endif
-#ifndef ST7920_DELAY_2
-  #define ST7920_DELAY_2 DELAY_NS(48)
-#endif
-#ifndef ST7920_DELAY_3
-  #define ST7920_DELAY_3 DELAY_NS(715)
-#endif

Marlin/src/pins/stm32/pins_FYSETC_S6.h

@@ -1,266 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 3 || E_STEPPERS > 3
-  #error "RUMBA32 supports up to 3 hotends / E-steppers."
-#endif
-
-#ifndef BOARD_INFO_NAME
-  #define BOARD_INFO_NAME "FYSETC_S6"
-#endif
-#ifndef DEFAULT_MACHINE_NAME
-  #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
-#endif
-
-// change the prio to 3 , 2 is for software serial
-//#define TEMP_TIMER_IRQ_PRIO 3
-
-//
-// EEPROM Emulation
-//
-#define FLASH_EEPROM_EMULATION
-#if ENABLED(FLASH_EEPROM_EMULATION)
-  #define FLASH_EEPROM_LEVELING
-#endif
-//#define SRAM_EEPROM_EMULATION
-//#define I2C_EEPROM
-#ifdef I2C_EEPROM
-  #undef E2END // Defined in Arduino Core STM32 to be used with EEPROM emulation. This board uses a real EEPROM.
-  #define E2END 0xFFF // 4KB
-#endif
-
-//
-// Servos
-//
-#define SERVO0_PIN         PA3
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PB14
-#define X_MAX_PIN          PA1
-#define Y_MIN_PIN          PB13
-#define Y_MAX_PIN          PA2
-#define Z_MIN_PIN          PA0
-#define Z_MAX_PIN          PA3
-
-//
-// Filament Sensor
-// share with X_MAX_PIN
-//
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN   PA1
-#endif
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PE11
-#define X_DIR_PIN          PE10
-#define X_ENABLE_PIN       PE12
-#define X_CS_PIN           PE7
-
-#define Y_STEP_PIN         PD8
-#define Y_DIR_PIN          PB12
-#define Y_ENABLE_PIN       PD9
-#define Y_CS_PIN           PE15
-
-#define Z_STEP_PIN         PD14
-#define Z_DIR_PIN          PD13
-#define Z_ENABLE_PIN       PD15
-#define Z_CS_PIN           PD10
-
-#define E0_STEP_PIN        PD5
-#define E0_DIR_PIN         PD6
-#define E0_ENABLE_PIN      PD4
-#define E0_CS_PIN          PD7
-
-#define E1_STEP_PIN        PE6
-#define E1_DIR_PIN         PC13
-#define E1_ENABLE_PIN      PE5
-#define E1_CS_PIN          PC14
-
-#define E2_STEP_PIN        PE2
-#define E2_DIR_PIN         PE4
-#define E2_ENABLE_PIN      PE3
-#define E2_CS_PIN          PC15
-
-#if HAS_TMC220x
-  //
-  // TMC2208/TMC2209 stepper drivers
-  //
-
-  //
-  // Software serial
-  //
-  #define X_SERIAL_TX_PIN  PE9
-  #define X_SERIAL_RX_PIN  PE8
-
-  #define Y_SERIAL_TX_PIN  PE14
-  #define Y_SERIAL_RX_PIN  PE13
-
-  #define Z_SERIAL_TX_PIN  PD11
-  #define Z_SERIAL_RX_PIN  PD12
-
-  #define E0_SERIAL_TX_PIN PD3
-  #define E0_SERIAL_RX_PIN PA15
-
-  #define E1_SERIAL_TX_PIN PC4
-  #define E1_SERIAL_RX_PIN PC5
-
-  #define E2_SERIAL_TX_PIN PE1
-  #define E2_SERIAL_RX_PIN PE0
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC0
-#define TEMP_1_PIN         PC1
-#define TEMP_2_PIN         PC2
-#define TEMP_BED_PIN       PC3
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PB3
-#define HEATER_1_PIN       PB4
-#define HEATER_2_PIN       PB15
-#define HEATER_BED_PIN     PC8
-
-#define FAN_PIN            PB0
-#define FAN1_PIN           PB1
-#define FAN2_PIN           PB2
-
-//
-// SPI
-//
-#define SCK_PIN            PA5
-#define MISO_PIN           PA6
-#define MOSI_PIN           PA7
-
-//
-// Misc. Functions
-//
-//#define LED_PIN            PB14
-//#define BTN_PIN            PC10
-//#define PS_ON_PIN          PE11
-//#define KILL_PIN           PC5
-
-#define SDSS               PA4
-#define SD_DETECT_PIN  	   PB10
-
-//
-// LCD / Controller
-//
-#if HAS_SPI_LCD
-  #define BEEPER_PIN       PC9
-  #define BTN_ENC          PA8
-
-  #if ENABLED(CR10_STOCKDISPLAY)
-    #define LCD_PINS_RS    PD0
-
-    #define BTN_EN1        PC11
-    #define BTN_EN2        PC10
-
-    #define LCD_PINS_ENABLE PD1
-    #define LCD_PINS_D4    PC12
-
-    // CR10_Stock Display needs a different delay setting on SKR PRO v1.1, so undef it here.
-    // It will be defined again at the #HAS_GRAPHICAL_LCD section below.
-    #undef ST7920_DELAY_1
-    #undef ST7920_DELAY_2
-    #undef ST7920_DELAY_3
-
-  #else
-
-    #define LCD_PINS_RS    PD2
-
-    #define BTN_EN1        PC6
-    #define BTN_EN2        PC7
-
-    #define LCD_SDSS       PA4
-
-    #define LCD_PINS_ENABLE PC11
-    #define LCD_PINS_D4    PC10
-
-    #if ENABLED(FYSETC_MINI_12864)
-     // See https://wiki.fysetc.com/Mini12864_Panel
-      #define DOGLCD_CS    PC11
-      #define DOGLCD_A0    PD2
-      #if ENABLED(FYSETC_GENERIC_12864_1_1)
-        #define LCD_BACKLIGHT_PIN PD0
-      #endif
-      #define LCD_RESET_PIN PC10   // Must be high or open for LCD to operate normally.
-      #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
-        #ifndef RGB_LED_R_PIN
-          #define RGB_LED_R_PIN PC12
-        #endif
-        #ifndef RGB_LED_G_PIN
-          #define RGB_LED_G_PIN PD0
-        #endif
-        #ifndef RGB_LED_B_PIN
-          #define RGB_LED_B_PIN PD1
-        #endif
-      #elif ENABLED(FYSETC_MINI_12864_2_1)
-        #define NEOPIXEL_PIN    PC12
-      #endif
-    #endif // !FYSETC_MINI_12864
-
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  PC12
-      #define LCD_PINS_D6  PD0
-      #define LCD_PINS_D7  PD1
-    #endif
-
-  #endif
-
-  // Alter timing for graphical display
-  #if HAS_GRAPHICAL_LCD
-    #ifndef ST7920_DELAY_1
-      #define ST7920_DELAY_1 DELAY_NS(96)
-    #endif
-    #ifndef ST7920_DELAY_2
-      #define ST7920_DELAY_2 DELAY_NS(48)
-    #endif
-    #ifndef ST7920_DELAY_3
-      #define ST7920_DELAY_3 DELAY_NS(600)
-    #endif
-  #endif
-
-#endif // HAS_SPI_LCD
-
-#ifndef RGB_LED_R_PIN
-  #define RGB_LED_R_PIN    PB6
-#endif
-#ifndef RGB_LED_G_PIN
-  #define RGB_LED_G_PIN    PB5
-#endif
-#ifndef RGB_LED_B_PIN
-  #define RGB_LED_B_PIN    PB7
-#endif
-#ifndef RGB_LED_W_PIN
-  #define RGB_LED_W_PIN    -1
-#endif

Marlin/src/pins/stm32/pins_GENERIC_STM32F4.h

@@ -1,190 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * To build with Arduino IDE use "Discovery F407VG"
- * To build with PlatformIO use environment "STM32F4"
- */
-#if !defined(STM32F4) && !defined(STM32F4xx)
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "STM32F4 supports up to 2 hotends / E-steppers."
-#endif
-
-#define BOARD_INFO_NAME      "Misc. STM32F4"
-#define DEFAULT_MACHINE_NAME "STM32F407VET6"
-
-//#define I2C_EEPROM
-
-#ifndef E2END
-  #define E2END 0xFFF // 4KB
-#endif
-
-// Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PE0
-#define X_MAX_PIN          -1
-#define Y_MIN_PIN          PE1
-#define Y_MAX_PIN          -1
-#define Z_MIN_PIN          PE14
-#define Z_MAX_PIN          -1
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-
-//#ifndef Z_MIN_PROBE_PIN
-//  #define Z_MIN_PROBE_PIN  PA4
-//#endif
-
-//
-// Steppers
-//
-
-#define X_STEP_PIN         PD3
-#define X_DIR_PIN          PD2
-#define X_ENABLE_PIN       PD0
-//#ifndef X_CS_PIN
-//  #define X_CS_PIN         PD1
-//#endif
-
-#define Y_STEP_PIN         PE11
-#define Y_DIR_PIN          PE10
-#define Y_ENABLE_PIN       PE13
-//#ifndef Y_CS_PIN
-//  #define Y_CS_PIN         PE12
-//#endif
-
-#define Z_STEP_PIN         PD6
-#define Z_DIR_PIN          PD7
-#define Z_ENABLE_PIN       PD4
-//#ifndef Z_CS_PIN
-//  #define Z_CS_PIN         PD5
-//#endif
-
-#define E0_STEP_PIN        PB5
-#define E0_DIR_PIN         PB6
-#define E0_ENABLE_PIN      PB3
-//#ifndef E0_CS_PIN
-//  #define E0_CS_PIN         PB4
-//#endif
-
-#define E1_STEP_PIN        PE4
-#define E1_DIR_PIN         PE2
-#define E1_ENABLE_PIN      PE3
-//#ifndef E1_CS_PIN
-//  #define E1_CS_PIN         PE5
-//#endif
-
-#define SCK_PIN            PA5
-#define MISO_PIN           PA6
-#define MOSI_PIN           PA7
-
-//
-// Temperature Sensors
-//
-
-#define TEMP_0_PIN         PC0   // Analog Input
-#define TEMP_1_PIN         PC1   // Analog Input
-#define TEMP_BED_PIN       PC2   // Analog Input
-
-//
-// Heaters / Fans
-//
-
-#define HEATER_0_PIN       PA1
-#define HEATER_1_PIN       PA2
-#define HEATER_BED_PIN     PA0
-
-#ifndef FAN_PIN
-  #define FAN_PIN          PC6
-#endif
-#define FAN1_PIN           PC7
-#define FAN2_PIN           PC8
-
-#define ORIG_E0_AUTO_FAN_PIN  FAN1_PIN // Use this by NOT overriding E0_AUTO_FAN_PIN
-
-//
-// Misc. Functions
-//
-
-//#define CASE_LIGHT_PIN_CI PF13
-//#define CASE_LIGHT_PIN_DO PF14
-//#define NEOPIXEL_PIN      PF13
-
-//
-// Průša i3 MK2 Multi Material Multiplexer Support
-//
-
-//#define E_MUX0_PIN         PG3
-//#define E_MUX1_PIN         PG4
-
-//
-// Servos
-//
-
-//#define SERVO0_PIN         PE13
-//#define SERVO1_PIN         PE14
-
-
-#define SDSS               PE7
-#define SS_PIN             PE7
-#define LED_PIN            PB7         //Alive
-#define PS_ON_PIN          PA10
-#define KILL_PIN           PA8
-#define PWR_LOSS           PA4         //Power loss / nAC_FAULT
-
-//
-// LCD / Controller
-//
-
-#define SD_DETECT_PIN      PA15
-#define BEEPER_PIN         PC9
-#define LCD_PINS_RS        PE9
-#define LCD_PINS_ENABLE    PE8
-#define LCD_PINS_D4        PB12
-#define LCD_PINS_D5        PB13
-#define LCD_PINS_D6        PB14
-#define LCD_PINS_D7        PB15
-#define BTN_EN1            PC4
-#define BTN_EN2            PC5
-#define BTN_ENC            PC3
-
-//
-// Filament runout
-//
-
-#define FIL_RUNOUT_PIN     PA3
-
-//
-// ST7920 Delays
-//
-#if HAS_GRAPHICAL_LCD
-  #define BOARD_ST7920_DELAY_1 DELAY_NS(96)
-  #define BOARD_ST7920_DELAY_2 DELAY_NS(48)
-  #define BOARD_ST7920_DELAY_3 DELAY_NS(715)
-#endif

Marlin/src/pins/stm32/pins_LERDGE_K.h

@@ -1,177 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#if !defined(STM32F4) && !defined(STM32F4xx)
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "LERDGE K supports up to 2 hotends / E-steppers."
-#endif
-
-#define BOARD_INFO_NAME      "Lerdge K"
-#define DEFAULT_MACHINE_NAME "LERDGE"
-
-#define I2C_EEPROM
-
-// Ignore temp readings during develpment.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
-
-//
-// Servos
-//
-//#define SERVO0_PIN         PD12
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PG3
-#define Y_STOP_PIN         PG4
-#define Z_STOP_PIN         PG5
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-//#ifndef Z_MIN_PROBE_PIN
-//  #define Z_MIN_PROBE_PIN  PB15
-//#endif
-
-//
-// Filament runout
-//
-#define FIL_RUNOUT_PIN     PE6
-#define FIL_RUNOUT2_PIN    PE7
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PG1
-#define X_DIR_PIN          PB10
-#define X_ENABLE_PIN       PG0
-//#ifndef X_CS_PIN
-//  #define X_CS_PIN       PE0
-//#endif
-
-#define Y_STEP_PIN         PF14
-#define Y_DIR_PIN          PF15
-#define Y_ENABLE_PIN       PF13
-//#ifndef Y_CS_PIN
-//  #define Y_CS_PIN       PE1
-//#endif
-
-#define Z_STEP_PIN         PF11
-#define Z_DIR_PIN          PF12
-#define Z_ENABLE_PIN       PC5
-//#ifndef Z_CS_PIN
-//  #define Z_CS_PIN       PE2
-//#endif
-
-#define E0_STEP_PIN        PC14
-#define E0_DIR_PIN         PC13
-#define E0_ENABLE_PIN      PC15
-//#ifndef E0_CS_PIN
-//  #define E0_CS_PIN      PE3
-//#endif
-
-#define E1_STEP_PIN        PF1
-#define E1_DIR_PIN         PF0
-#define E1_ENABLE_PIN      PF2
-//#ifndef E1_CS_PIN
-//  #define E1_CS_PIN      PE4
-//#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // Analog Input
-#define TEMP_1_PIN         PC2   // Analog Input
-#define TEMP_BED_PIN       PC0   // Analog Input
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PA1
-#define HEATER_1_PIN       PA0
-#define HEATER_BED_PIN     PA2
-
-#ifndef FAN_PIN
-  #define FAN_PIN          PC15
-#endif
-#define FAN1_PIN           PF6
-#define FAN2_PIN           PF7
-
-#define ORIG_E0_AUTO_FAN_PIN  FAN1_PIN // Use this by NOT overriding E0_AUTO_FAN_PIN
-
-//
-// LED / Lighting
-//
-//#define CASE_LIGHT_PIN_CI -1
-//#define CASE_LIGHT_PIN_DO -1
-//#define NEOPIXEL_PIN      -1
-
-//
-// Prusa i3 MK2 Multi-Material Multiplexer Support
-//
-//#define E_MUX0_PIN         -1
-//#define E_MUX1_PIN         -1
-
-//
-// SD support
-//
-#define SDIO_SUPPORT
-
-//
-// Misc. Functions
-//
-#define SDSS               PC11
-#define LED_PIN            PC7   // Alive
-#define PS_ON_PIN          -1
-#define KILL_PIN           -1
-#define POWER_LOSS_PIN     -1    // Power-loss / nAC_FAULT
-
-#define SCK_PIN            PC12
-#define MISO_PIN           PC8
-#define MOSI_PIN           PD2
-#define SS_PIN             PC11
-
-//
-// LCD / Controller
-//
-
-// TODO: Replace these with the correct FSMC pins, once known
-#define SD_DETECT_PIN      -1
-#define BEEPER_PIN         PD12
-#define LCD_PINS_RS        -1
-#define LCD_PINS_ENABLE    -1
-#define LCD_PINS_D4        -1
-#define LCD_PINS_D5        -1
-#define LCD_PINS_D6        -1
-#define LCD_PINS_D7        -1
-
-#define BTN_EN1            PE3
-#define BTN_EN2            PE4
-#define BTN_ENC            PE2
-
-//
-// ST7920 Delays
-//
-#if HAS_GRAPHICAL_LCD
-  #define BOARD_ST7920_DELAY_1 DELAY_NS(96)
-  #define BOARD_ST7920_DELAY_2 DELAY_NS(48)
-  #define BOARD_ST7920_DELAY_3 DELAY_NS(715)
-#endif

Marlin/src/pins/stm32/pins_LERDGE_X.h

@@ -1,174 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#if !defined(STM32F4) && !defined(STM32F4xx)
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "LERDGE X supports up to 2 hotends / E-steppers."
-#endif
-
-#define BOARD_INFO_NAME      "Lerdge X"
-#define DEFAULT_MACHINE_NAME "LERDGE"
-
-//#define I2C_EEPROM
-
-//
-// Servos
-//
-//#define SERVO0_PIN         PD12
-//#define SERVO1_PIN         -1
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PB12
-#define Y_STOP_PIN         PB13
-#define Z_STOP_PIN         PB14
-
-//
-// Filament runout
-//
-#define FIL_RUNOUT_PIN     PE1
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-//#ifndef Z_MIN_PROBE_PIN
-//  #define Z_MIN_PROBE_PIN  PB15
-//#endif
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PB10
-#define X_DIR_PIN          PB2
-#define X_ENABLE_PIN       PB11
-//#ifndef X_CS_PIN
-//  #define X_CS_PIN       PD1
-//#endif
-
-#define Y_STEP_PIN         PB0
-#define Y_DIR_PIN          PC5
-#define Y_ENABLE_PIN       PB1
-//#ifndef Y_CS_PIN
-//  #define Y_CS_PIN       PE12
-//#endif
-
-#define Z_STEP_PIN         PA7
-#define Z_DIR_PIN          PA6
-#define Z_ENABLE_PIN       PC4
-//#ifndef Z_CS_PIN
-//  #define Z_CS_PIN       PD5
-//#endif
-
-#define E0_STEP_PIN        PA4
-#define E0_DIR_PIN         PA3
-#define E0_ENABLE_PIN      PA5
-//#ifndef E0_CS_PIN
-//  #define E0_CS_PIN      PB4
-//#endif
-
-#define E1_STEP_PIN        -1
-#define E1_DIR_PIN         -1
-#define E1_ENABLE_PIN      -1
-//#ifndef E1_CS_PIN
-//  #define E1_CS_PIN      PE5
-//#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC0   // Analog Input
-#define TEMP_1_PIN         -1    // Analog Input
-#define TEMP_BED_PIN       PC1   // Analog Input
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PA1
-#define HEATER_1_PIN       -1
-#define HEATER_BED_PIN     PA2
-
-#ifndef FAN_PIN
-//  #define FAN_PIN        PC15
-#endif
-#define FAN1_PIN           PC15
-#define FAN2_PIN           PA0
-
-#define ORIG_E0_AUTO_FAN_PIN PC15   // Use this by NOT overriding E0_AUTO_FAN_PIN
-
-//
-// Prusa i3 MK2 Multi Material Multiplexer Support
-//
-//#define E_MUX0_PIN       -1
-//#define E_MUX1_PIN       -1
-
-//
-// LED / Lighting
-//
-//#define CASE_LIGHT_PIN_CI -1
-//#define CASE_LIGHT_PIN_DO -1
-//#define NEOPIXEL_PIN     -1
-
-//
-// Misc. Functions
-//
-#define SDSS               PC11
-#define LED_PIN            PC7   // Alive
-#define PS_ON_PIN          -1
-#define KILL_PIN           -1
-#define POWER_LOSS_PIN     -1    // Power-loss / nAC_FAULT
-
-#define SCK_PIN            PC12
-#define MISO_PIN           PC8
-#define MOSI_PIN           PD2
-#define SS_PIN             PC11
-
-//
-// SD support
-//
-#define SDIO_SUPPORT
-
-//
-// LCD / Controller
-//
-
-// The LCD is initialized in FSMC mode
-#define SD_DETECT_PIN      -1
-#define BEEPER_PIN         PD12
-
-#define BTN_EN1            PE3
-#define BTN_EN2            PE4
-#define BTN_ENC            PE2
-
-#define LCD_RESET_PIN      PD6
-#define LCD_BACKLIGHT_PIN  PD3
-#define FSMC_CS_PIN        PD4
-#define FSMC_RS_PIN        PD11
-#define TOUCH_CS           PB6
-
-//
-// ST7920 Delays
-//
-#if HAS_GRAPHICAL_LCD
-  #define BOARD_ST7920_DELAY_1 DELAY_NS(96)
-  #define BOARD_ST7920_DELAY_2 DELAY_NS(48)
-  #define BOARD_ST7920_DELAY_3 DELAY_NS(715)
-#endif

Marlin/src/pins/stm32/pins_LONGER3D_LK.h

@@ -1,170 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * Longer3D LK1/LK2 & Alfawise U20/U30 (STM32F103VET6) board pin assignments
- */
-
-#if !defined(__STM32F1__) && !defined(STM32F1xx)
-  #error "Oops! Select a STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 1 || E_STEPPERS > 1
-  #error "Longer3D board only supports 1 hotend / E-stepper. Comment out this line to continue."
-#endif
-
-#define BOARD_INFO_NAME "Longer3D"
-#define ALFAWISE_UX0             // Common to all Longer3D STM32F1 boards (used for Open drain mosfets)
-
-//#define DISABLE_DEBUG          //  We still want to debug with STLINK...
-#define DISABLE_JTAG             //  We free the jtag pins (PA15) but keep STLINK
-                                 //  Release PB4 (STEP_X_PIN) from JTAG NRST role.
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PC1   // pin 16
-#define X_MAX_PIN          PC0   // pin 15 (Filament sensor on Alfawise setup)
-#define Y_MIN_PIN          PC15  // pin 9
-#define Y_MAX_PIN          PC14  // pin 8 (Unused in stock Alfawise setup)
-#define Z_MIN_PIN          PE6   // pin 5 Standard Endstop or Z_Probe endstop function
-#define Z_MAX_PIN          PE5   // pin 4 (Unused in stock Alfawise setup)
-                                 // May be used for BLTouch Servo function on older variants (<= V08)
-#define ONBOARD_ENDSTOPPULLUPS
-
-//
-// Filament Sensor
-//
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN   PC0   // XMAX plug on PCB used as filament runout sensor on Alfawise boards (inverting true)
-#endif
-
-//
-// Steppers
-//
-#define X_ENABLE_PIN       PB5   // pin 91
-#define X_STEP_PIN         PB4   // pin 90
-#define X_DIR_PIN          PB3   // pin 89
-
-#define Y_ENABLE_PIN       PB8   // pin 95
-#define Y_STEP_PIN         PB7   // pin 93
-#define Y_DIR_PIN          PB6   // pin 92
-
-#define Z_ENABLE_PIN       PE1   // pin 98
-#define Z_STEP_PIN         PE0   // pin 97
-#define Z_DIR_PIN          PB9   // pin 96
-
-#define E0_ENABLE_PIN      PE4   // pin 3
-#define E0_STEP_PIN        PE3   // pin 2
-#define E0_DIR_PIN         PE2   // pin 1
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PA0   // pin 23 (Nozzle 100K/3950 thermistor)
-#define TEMP_BED_PIN       PA1   // pin 24 (Hot Bed 100K/3950 thermistor)
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PD3   // pin 84 (Nozzle Heat Mosfet)
-#define HEATER_BED_PIN     PA8   // pin 67 (Hot Bed Mosfet)
-
-#define FAN_PIN            PA15  // pin 77 (4cm Fan)
-#define FAN_SOFT_PWM             // Required to avoid issues with heating or STLink
-#define FAN_MIN_PWM        35    // Fan will not start in 1-30 range
-#define FAN_MAX_PWM        255
-
-//#define BEEPER_PIN       PD13  // pin 60 (Servo PWM output 5V/GND on Board V0G+) made for BL-Touch sensor
-                                 // Can drive a PC Buzzer, if connected between PWM and 5V pins
-
-#define LED_PIN            PC2   // pin 17
-
-//
-// PWM for a servo probe
-// Other servo devices are not supported on this board!
-//
-#if HAS_Z_SERVO_PROBE
-  #define SERVO0_PIN       PD13  // Open drain PWM pin on the V0G (GND or floating 5V)
-  #define SERVO0_PWM_OD          // Comment this if using PE5
-
-  //#define SERVO0_PIN     PE5   // Pulled up PWM pin on the V08 (3.3V or 0)
-  //#undef Z_MAX_PIN             // Uncomment if using ZMAX connector (PE5)
-#endif
-
-/**
- * Note: Alfawise screens use various TFT controllers. Supported screens
- * are based on the ILI9341, ILI9328 and ST7798V. Define init sequences for
- * other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp
- *
- * If the screen stays white, disable 'LCD_RESET_PIN' to let the bootloader
- * init the screen.
- *
- * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
- * because Marlin uses the reset as a failsafe to revive a glitchy LCD.
- */
-
-#define LCD_RESET_PIN      PC4   // pin 33
-#define LCD_BACKLIGHT_PIN  PD12  // pin 59
-#define FSMC_CS_PIN        PD7   // pin 88 = FSMC_NE1
-#define FSMC_RS_PIN        PD11  // pin 58 A16 Register. Only one address needed
-
-#define LCD_USE_DMA_FSMC   // Use DMA transfers to send data to the TFT
-#define FSMC_DMA_DEV       DMA2
-#define FSMC_DMA_CHANNEL   DMA_CH5
-
-#define DOGLCD_MOSI        -1  // Prevent auto-define by Conditionals_post.h
-#define DOGLCD_SCK         -1
-
-/**
- * Note: Alfawise U20/U30 boards DON'T use SPI2, as the hardware designer
- * mixed up MOSI and MISO pins. SPI is managed in SW, and needs pins
- * declared below.
- */
-#if ENABLED(TOUCH_BUTTONS)
-  #define TOUCH_CS_PIN     PB12  // pin 51 SPI2_NSS
-  #define TOUCH_SCK_PIN    PB13  // pin 52
-  #define TOUCH_MOSI_PIN   PB14  // pin 53
-  #define TOUCH_MISO_PIN   PB15  // pin 54
-  #define TOUCH_INT_PIN    PC6   // pin 63 (PenIRQ coming from ADS7843)
-#endif
-
-//
-// Persistent Storage
-// If no option is selected below the SD Card will be used
-//
-//#define SPI_EEPROM
-#define FLASH_EEPROM_EMULATION
-
-#undef E2END
-#if ENABLED(SPI_EEPROM)
-  // SPI1 EEPROM Winbond W25Q64 (8MB/64Mbits)
-  #define SPI_CHAN_EEPROM1   1
-  #define SPI_EEPROM1_CS     PC5   // pin 34
-  #define EEPROM_SCK  BOARD_SPI1_SCK_PIN    // PA5 pin 30
-  #define EEPROM_MISO BOARD_SPI1_MISO_PIN   // PA6 pin 31
-  #define EEPROM_MOSI BOARD_SPI1_MOSI_PIN   // PA7 pin 32
-  #define EEPROM_PAGE_SIZE   0x1000U        // 4KB (from datasheet)
-  #define E2END ((16 * EEPROM_PAGE_SIZE)-1) // Limit to 64KB for now...
-#elif ENABLED(FLASH_EEPROM_EMULATION)
-  // SoC Flash (framework-arduinoststm32-maple/STM32F1/libraries/EEPROM/EEPROM.h)
-  #define EEPROM_START_ADDRESS (0x8000000UL + (512 * 1024) - 2 * EEPROM_PAGE_SIZE)
-  #define EEPROM_PAGE_SIZE     (0x800U)     // 2KB, but will use 2x more (4KB)
-  #define E2END (EEPROM_PAGE_SIZE - 1)
-#else
-  #define E2END (0x7FFU) // On SD, Limit to 2KB, require this amount of RAM
-#endif

Marlin/src/pins/stm32/pins_MKS_ROBIN.h

@@ -1,159 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * MKS Robin (STM32F130ZET6) board pin assignments
- *
- * https://github.com/makerbase-mks/MKS-Robin/tree/master/MKS%20Robin/Hardware
- */
-
-#ifndef __STM32F1__
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "MKS Robin supports up to 2 hotends / E-steppers. Comment out this line to continue."
-#endif
-
-#define BOARD_INFO_NAME "MKS Robin"
-
-//
-// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
-//
-#define DISABLE_JTAG
-
-//
-// Servos
-//
-#define SERVO0_PIN         PC3   // XS1 - 5
-#define SERVO1_PIN         PA1   // XS1 - 6
-#define SERVO2_PIN         PF9   // XS2 - 5
-#define SERVO3_PIN         PF8   // XS2 - 6
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PB12
-#define X_MAX_PIN          PB0
-#define Y_MIN_PIN          PC5
-#define Y_MAX_PIN          PC4
-#define Z_MIN_PIN          PA4
-#define Z_MAX_PIN          PF7
-
-//
-// Steppers
-//
-#define X_ENABLE_PIN       PB9
-#define X_STEP_PIN         PB8
-#define X_DIR_PIN          PB5
-
-#define Y_ENABLE_PIN       PB4
-#define Y_STEP_PIN         PG15
-#define Y_DIR_PIN          PG10
-
-#define Z_ENABLE_PIN       PD7
-#define Z_STEP_PIN         PD3
-#define Z_DIR_PIN          PG14
-
-#define E0_ENABLE_PIN      PG13
-#define E0_STEP_PIN        PG8
-#define E0_DIR_PIN         PA15
-
-#define E1_ENABLE_PIN      PA12
-#define E1_STEP_PIN        PA11
-#define E1_DIR_PIN         PA8
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // TH1
-#define TEMP_1_PIN         PC2   // TH2
-#define TEMP_BED_PIN       PC0   // TB1
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PC7   // HEATER1
-#define HEATER_1_PIN       PA6   // HEATER2
-#define HEATER_BED_PIN     PC6   // HOT BED
-
-#define FAN_PIN            PA7   // FAN
-
-/**
- * Note: MKS Robin board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
- */
-//#define MAX6675_SS_PIN     PE5  // TC1 - CS1
-//#define MAX6675_SS_PIN     PE6  // TC2 - CS2
-
-#define POWER_LOSS_PIN     PA2   // PW_DET
-#define PS_ON_PIN          PA3   // PW_OFF
-#define FIL_RUNOUT_PIN     PF11  // MT_DET
-
-#define BEEPER_PIN         PC13
-#define LED_PIN            PB2
-
-/**
- * Note: MKS Robin TFT screens use various TFT controllers
- * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
- * ILI9488 is not supported
- * Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp
- *
- * If the screen stays white, disable 'LCD_RESET_PIN'
- * to let the bootloader init the screen.
- *
- * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
- * because Marlin uses the reset as a failsafe to revive a glitchy LCD.
- */
-//#define LCD_RESET_PIN      PF6
-#define LCD_BACKLIGHT_PIN  PG11
-#define FSMC_CS_PIN        PG12  // NE4
-#define FSMC_RS_PIN        PF0   // A0
-
-#define LCD_USE_DMA_FSMC   // Use DMA transfers to send data to the TFT
-#define FSMC_DMA_DEV       DMA2
-#define FSMC_DMA_CHANNEL   DMA_CH5
-
-#if ENABLED(TOUCH_BUTTONS)
-  #define TOUCH_CS_PIN     PB1   // SPI2_NSS
-  #define TOUCH_SCK_PIN    PB13  // SPI2_SCK
-  #define TOUCH_MISO_PIN   PB14  // SPI2_MISO
-  #define TOUCH_MOSI_PIN   PB15  // SPI2_MOSI
-#endif
-
-// SPI1(PA7) & SPI3(PB5) not available
-#define ENABLE_SPI2
-
-#if ENABLED(SDIO_SUPPORT)
-  #define SCK_PIN           PB13 // SPI2
-  #define MISO_PIN          PB14 // SPI2
-  #define MOSI_PIN          PB15 // SPI2
-  #define SS_PIN            -1   // PB12 is X-
-  #define SD_DETECT_PIN     PF12 // SD_CD
-#else
-  // SD as custom software SPI (SDIO pins)
-  #define SCK_PIN           PC12
-  #define MISO_PIN          PC8
-  #define MOSI_PIN          PD2
-  #define SS_PIN            -1
-  #define ONBOARD_SD_CS_PIN PC11
-  #define SDSS              PD2
-  #define SD_DETECT_PIN     -1
-#endif

Marlin/src/pins/stm32/pins_MKS_ROBIN2.h

@@ -1,102 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "MKS_ROBIN2 supports up to 2 hotends / E-steppers."
-#endif
-
-#ifndef BOARD_INFO_NAME
-  #define BOARD_NAME "MKS_ROBIN2"
-#endif
-
-#ifndef DEFAULT_MACHINE_NAME
-  #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
-#endif
-
-#define SRAM_EEPROM_EMULATION
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PG8
-#define X_MAX_PIN          PG7
-#define Y_MIN_PIN          PG6
-#define Y_MAX_PIN          PG5
-#define Z_MIN_PIN          PG4
-#define Z_MAX_PIN          PG3
-
-//
-// Servos
-//
-#define SERVO0_PIN         PB0   // XS2-5
-#define SERVO1_PIN         PF7   // XS1-5
-#define SERVO2_PIN         PF8   // XS1-6
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PE6
-#define X_DIR_PIN          PE5
-#define X_ENABLE_PIN       PC13
-
-#define Y_STEP_PIN         PE3
-#define Y_DIR_PIN          PE2
-#define Y_ENABLE_PIN       PE4
-
-#define Z_STEP_PIN         PE0
-#define Z_DIR_PIN          PB9
-#define Z_ENABLE_PIN       PE1
-
-#define E0_STEP_PIN        PG10
-#define E0_DIR_PIN         PG9
-#define E0_ENABLE_PIN      PB8
-
-#define E1_STEP_PIN        PD3
-#define E1_DIR_PIN         PA15
-#define E1_ENABLE_PIN      PD6
-
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // T1 <-> E0
-#define TEMP_1_PIN         PC2   // T2 <-> E1
-#define TEMP_BED_PIN       PC0   // T0 <-> Bed
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PF3   // Heater0
-#define HEATER_1_PIN       PF2   // Heater1
-#define HEATER_BED_PIN     PF4   // Hotbed
-#define FAN_PIN            PA7   // Fan0
-
-//
-// Misc. Functions
-//
-#define SDSS               -1    // PB12
-
-#define SD_DETECT_PIN      PF9
-#define BEEPER_PIN         PG2

Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h

@@ -1,137 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef __STM32F1__
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 1 || E_STEPPERS > 1
-  #error "MKS Robin Lite supports only 1 hotend / E-stepper. Comment out this line to continue."
-#endif
-
-#ifndef BOARD_INFO_NAME
-  #define BOARD_INFO_NAME "MKS Robin Lite"
-#endif
-#define BOARD_WEBSITE_URL "github.com/makerbase-mks"
-
-//#define DISABLE_DEBUG
-#define DISABLE_JTAG
-#define ENABLE_SPI2
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PC13
-#define Y_STOP_PIN         PC0
-#define Z_MIN_PIN          PC12
-#define Z_MAX_PIN          PB9
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PC6
-#define X_DIR_PIN          PB12
-#define X_ENABLE_PIN       PB10
-
-#define Y_STEP_PIN         PB11
-#define Y_DIR_PIN          PB2
-#define Y_ENABLE_PIN       PB10
-
-#define Z_STEP_PIN         PB1
-#define Z_DIR_PIN          PC5
-#define Z_ENABLE_PIN       PB10
-
-#define E0_STEP_PIN        PC4
-#define E0_DIR_PIN         PA5
-#define E0_ENABLE_PIN      PA4
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PC9
-#define FAN_PIN            PA8
-#define HEATER_BED_PIN     PC8
-
-//
-// Temperature Sensors
-//
-#define TEMP_BED_PIN       PA1
-#define TEMP_0_PIN         PA0
-
-#define FIL_RUNOUT_PIN     PB8  // MT_DET
-
-//
-// LCD Pins
-//
-#if HAS_SPI_LCD
-  #define BEEPER_PIN       PD2
-  #define BTN_ENC          PB3
-  #define LCD_PINS_RS      PC3
-
-  #define BTN_EN1          PB5
-  #define BTN_EN2          PB4
-
-  #define LCD_PINS_ENABLE  PC2
-
-  #if ENABLED(MKS_MINI_12864)
-
-    #define LCD_BACKLIGHT_PIN -1
-    #define LCD_RESET_PIN  -1
-    #define DOGLCD_A0      PC1
-    #define DOGLCD_CS      PC2
-    #define DOGLCD_SCK     PB13
-    #define DOGLCD_MOSI    PB15
-
-  #else // !MKS_MINI_12864
-
-    #define LCD_PINS_D4    PC1
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  -1
-      #define LCD_PINS_D6  -1
-      #define LCD_PINS_D7  -1
-    #endif
-
-  #endif // !MKS_MINI_12864
-
-#endif // HAS_SPI_LCD
-
-// Motor current PWM pins
-#define MOTOR_CURRENT_PWM_XY_PIN PB0
-#define MOTOR_CURRENT_PWM_Z_PIN  PA7
-#define MOTOR_CURRENT_PWM_E_PIN  PA6
-#define MOTOR_CURRENT_PWM_RANGE (65535/10/3.3) // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
-#define DEFAULT_PWM_MOTOR_CURRENT { 1000, 1000, 1000 } // 1.05Amp per driver, here is XY, Z and E. This values determined empirically.
-
-//
-// SD Card
-//
-#define ENABLE_SPI2
-#define SD_DETECT_PIN      PC10
-#define SCK_PIN            PB13
-#define MISO_PIN           P1B4
-#define MOSI_PIN           P1B5
-#define SS_PIN             PA15
-
-#if HAS_GRAPHICAL_LCD
-  #define BOARD_ST7920_DELAY_1 DELAY_NS(125)
-  #define BOARD_ST7920_DELAY_2 DELAY_NS(125)
-  #define BOARD_ST7920_DELAY_3 DELAY_NS(125)
-#endif

Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE3.h

@@ -1,153 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * MKS Robin Lite 3 (STM32F103RCT6) board pin assignments
- */
-
-#ifndef __STM32F1__
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "MKS Robin Lite3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
-#endif
-
-#ifndef BOARD_INFO_NAME
-  #define BOARD_INFO_NAME "MKS Robin Lite3"
-#endif
-#define BOARD_WEBSITE_URL "github.com/makerbase-mks"
-
-//#define DISABLE_DEBUG
-#define DISABLE_JTAG
-#define ENABLE_SPI2
-
-//
-// Servos
-//
-#define SERVO0_PIN         PA3
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN         PA12
-#define Y_STOP_PIN         PA11
-#define Z_MIN_PIN          PC6
-#define Z_MAX_PIN          PB1
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PC0
-#define X_DIR_PIN          PB2
-#define X_ENABLE_PIN       PC13
-
-#define Y_STEP_PIN         PC2
-#define Y_DIR_PIN          PB9
-#define Y_ENABLE_PIN       PB12
-
-#define Z_STEP_PIN         PB7
-#define Z_DIR_PIN          PB6
-#define Z_ENABLE_PIN       PB8
-
-#define E0_STEP_PIN        PB4
-#define E0_DIR_PIN         PB3
-#define E0_ENABLE_PIN      PB5
-
-#define E1_STEP_PIN        PC12
-#define E1_DIR_PIN         PC11
-#define E1_ENABLE_PIN      PD2
-
-//
-// Heaters 0,1 / Fans / Bed
-//
-#define HEATER_0_PIN       PC9
-#define HEATER_1_PIN       PC7
-#define FAN_PIN            PA8
-#define HEATER_BED_PIN     PC8
-
-//
-// Temperature Sensors
-//
-#define TEMP_BED_PIN       PA1  //TB
-#define TEMP_0_PIN         PA0  //TH1
-#define TEMP_1_PIN         PA2  //TH2
-
-#define FIL_RUNOUT_PIN     PB10 // MT_DET
-
-//
-// LCD Pins
-//
-#if HAS_SPI_LCD
-
-  #define BEEPER_PIN       PC1
-  #define BTN_ENC          PC3
-  #define LCD_PINS_ENABLE  PA4
-  #define LCD_PINS_RS      PA5
-  #define BTN_EN1          PB11
-  #define BTN_EN2          PB0
-
-  // MKS MINI12864 and MKS LCD12864B; If using MKS LCD12864A (Need to remove RPK2 resistor)
-  #if ENABLED(MKS_MINI_12864)
-
-    #define LCD_BACKLIGHT_PIN -1
-    #define LCD_RESET_PIN  -1
-    #define DOGLCD_A0      PC4
-    #define DOGLCD_CS      PA7
-    #define DOGLCD_SCK     PB13
-    #define DOGLCD_MOSI    PB15
-
-    // Required for MKS_MINI_12864 with this board
-    #define MKS_LCD12864B
-    #undef SHOW_BOOTSCREEN
-
-  #else // !MKS_MINI_12864
-
-    #define LCD_PINS_D4    PA6
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  PA7
-      #define LCD_PINS_D6  PC4
-      #define LCD_PINS_D7  PC5
-    #endif
-
-  #endif // !MKS_MINI_12864
-
-#endif // HAS_SPI_LCD
-
-//
-// SD Card
-//
-#define ENABLE_SPI2
-#define SD_DETECT_PIN      PC10
-#define SCK_PIN            PB13
-#define MISO_PIN           PB14
-#define MOSI_PIN           PB15
-#define SS_PIN             PA15
-
-#ifndef ST7920_DELAY_1
-  #define ST7920_DELAY_1 DELAY_NS(125)
-#endif
-#ifndef ST7920_DELAY_2
-  #define ST7920_DELAY_2 DELAY_NS(125)
-#endif
-#ifndef ST7920_DELAY_3
-  #define ST7920_DELAY_3 DELAY_NS(125)
-#endif

Marlin/src/pins/stm32/pins_MKS_ROBIN_NANO.h

@@ -1,137 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * MKS Robin nano (STM32F130VET6) board pin assignments
- */
-
-#ifndef __STM32F1__
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 2 || E_STEPPERS > 2
-  #error "MKS Robin nano supports up to 2 hotends / E-steppers. Comment out this line to continue."
-#endif
-
-#define BOARD_INFO_NAME "MKS Robin nano"
-
-//
-// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
-//
-#define DISABLE_DEBUG
-
-//
-// Limit Switches
-//
-#define X_STOP_PIN        PA15
-#define Y_STOP_PIN        PA12
-#define Z_MIN_PIN         PA11
-#define Z_MAX_PIN         PC4
-
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN   PA4   // MT_DET
-#endif
-
-//
-// Steppers
-//
-#define X_ENABLE_PIN       PE4
-#define X_STEP_PIN         PE3
-#define X_DIR_PIN          PE2
-
-#define Y_ENABLE_PIN       PE1
-#define Y_STEP_PIN         PE0
-#define Y_DIR_PIN          PB9
-
-#define Z_ENABLE_PIN       PB8
-#define Z_STEP_PIN         PB5
-#define Z_DIR_PIN          PB4
-
-#define E0_ENABLE_PIN      PB3
-#define E0_STEP_PIN        PD6
-#define E0_DIR_PIN         PD3
-
-#define E1_ENABLE_PIN      PA3
-#define E1_STEP_PIN        PA6
-#define E1_DIR_PIN         PA1
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // TH1
-#define TEMP_1_PIN         PC2   // TH2
-#define TEMP_BED_PIN       PC0   // TB1
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PC3   // HEATER1
-#define HEATER_1_PIN       PB0   // HEATER2
-#define HEATER_BED_PIN     PA0   // HOT BED
-
-#define FAN_PIN            PB1   // FAN
-
-//
-// Thermocouples
-//
-//#define MAX6675_SS_PIN     PE5  // TC1 - CS1
-//#define MAX6675_SS_PIN     PE6  // TC2 - CS2
-
-//
-// Misc. Functions
-//
-#define POWER_LOSS_PIN     PA2   // PW_DET
-#define PS_ON_PIN          PA3   // PW_OFF
-
-#define LED_PIN            PB2
-
-//
-// SD Card
-//
-#define SDIO_SUPPORT
-#define SD_DETECT_PIN      PD12
-
-//
-// LCD / Controller
-//
-#define BEEPER_PIN         PC5
-
-/**
- * Note: MKS Robin TFT screens use various TFT controllers.
- * If the screen stays white, disable 'LCD_RESET_PIN'
- * to let the bootloader init the screen.
- */
-#if ENABLED(FSMC_GRAPHICAL_TFT)
-  #define FSMC_CS_PIN        PD7    // NE4
-  #define FSMC_RS_PIN        PD11   // A0
-
-  #define LCD_RESET_PIN      PC6    // FSMC_RST
-  #define NO_LCD_REINIT             // Suppress LCD re-initialization
-
-  #define LCD_BACKLIGHT_PIN  PD13
-
-  #if ENABLED(TOUCH_BUTTONS)
-    #define TOUCH_CS_PIN     PA7  // SPI2_NSS
-    #define TOUCH_SCK_PIN    PB13 // SPI2_SCK
-    #define TOUCH_MISO_PIN   PB14 // SPI2_MISO
-    #define TOUCH_MOSI_PIN   PB15 // SPI2_MOSI
-  #endif
-#endif

Marlin/src/pins/stm32/pins_MKS_ROBIN_PRO.h

@@ -1,274 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * MKS Robin pro (STM32F103ZET6) board pin assignments
- */
-
-#ifndef __STM32F1__
-  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
-#elif HOTENDS > 3 || E_STEPPERS > 3
-  #error "MKS Robin pro supports up to 3 hotends / E-steppers. Comment out this line to continue."
-#endif
-
-#define BOARD_INFO_NAME "MKS Robin pro"
-
-//
-// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
-//
-#define DISABLE_DEBUG
-
-//
-// Note: MKS Robin board is using SPI2 interface.
-//
-//#define SPI_MODULE 2
-#define ENABLE_SPI2
-
-//
-// Servos
-//
-#define SERVO0_PIN         PA8   // BLTOUCH
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PA15
-#define X_MAX_PIN          PG7
-#define Y_MIN_PIN          PA12
-#define Y_MAX_PIN          PG8
-#define Z_MIN_PIN          PA11
-#define Z_MAX_PIN          PC4
-
-//
-// Steppers
-//
-#define X_ENABLE_PIN       PE4
-#define X_STEP_PIN         PE3
-#define X_DIR_PIN          PE2
-#ifndef X_CS_PIN
-  #define X_CS_PIN         PF8
-#endif
-
-#define Y_ENABLE_PIN       PE1
-#define Y_STEP_PIN         PE0
-#define Y_DIR_PIN          PB9
-#ifndef Y_CS_PIN
-  #define Y_CS_PIN         PF3
-#endif
-
-#define Z_ENABLE_PIN       PB8
-#define Z_STEP_PIN         PB5
-#define Z_DIR_PIN          PB4
-#ifndef Z_CS_PIN
-  #define Z_CS_PIN         PF6
-#endif
-
-#define E0_ENABLE_PIN      PB3
-#define E0_STEP_PIN        PD6
-#define E0_DIR_PIN         PD3
-#ifndef E0_CS_PIN
-  #define E0_CS_PIN        PG15
-#endif
-
-#define E1_ENABLE_PIN      PA3
-#define E1_STEP_PIN        PA6
-#define E1_DIR_PIN         PA1
-#ifndef E1_CS_PIN
-  #define E1_CS_PIN        PG10
-#endif
-
-#define E2_ENABLE_PIN      PF0
-#define E2_STEP_PIN        PF2
-#define E2_DIR_PIN         PF1
-#ifndef E2_CS_PIN
-  #define E2_CS_PIN        PG9
-#endif
-//
-// Software SPI pins for TMC2130 stepper drivers
-//
-#if ENABLED(TMC_USE_SW_SPI)
-  #ifndef TMC_SW_MOSI
-    #define TMC_SW_MOSI    PB15
-  #endif
-  #ifndef TMC_SW_MISO
-    #define TMC_SW_MISO    PB14
-  #endif
-  #ifndef TMC_SW_SCK
-    #define TMC_SW_SCK     PB13
-  #endif
-#endif
-
-#if HAS_TMC220x
-  /**
-   * TMC2208/TMC2209 stepper drivers
-   *
-   * Hardware serial communication ports.
-   * If undefined software serial is used according to the pins below
-   */
-  //#define X_HARDWARE_SERIAL  Serial
-  //#define X2_HARDWARE_SERIAL Serial1
-  //#define Y_HARDWARE_SERIAL  Serial1
-  //#define Y2_HARDWARE_SERIAL Serial1
-  //#define Z_HARDWARE_SERIAL  Serial1
-  //#define Z2_HARDWARE_SERIAL Serial1
-  //#define E0_HARDWARE_SERIAL Serial1
-  //#define E1_HARDWARE_SERIAL Serial1
-  //#define E2_HARDWARE_SERIAL Serial1
-  //#define E3_HARDWARE_SERIAL Serial1
-  //#define E4_HARDWARE_SERIAL Serial1
-
-  //
-  // Software serial
-  //
-  #define X_SERIAL_TX_PIN  PF7
-  #define X_SERIAL_RX_PIN  PF8
-
-  #define Y_SERIAL_TX_PIN  PF4
-  #define Y_SERIAL_RX_PIN  PF3
-
-  #define Z_SERIAL_TX_PIN  PF5
-  #define Z_SERIAL_RX_PIN  PF6
-
-  #define E0_SERIAL_TX_PIN PG13
-  #define E0_SERIAL_RX_PIN PG15
-
-  #define E1_SERIAL_TX_PIN PG12
-  #define E1_SERIAL_RX_PIN PG10
-
-  #define E2_SERIAL_TX_PIN PC13
-  #define E2_SERIAL_RX_PIN PG9
-#endif
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC1   // TH1
-#define TEMP_1_PIN         PC2   // TH2
-#define TEMP_2_PIN         PC3   // TH3
-#define TEMP_BED_PIN       PC0   // TB1
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PF10  // +HE0-
-#define HEATER_1_PIN       PB0   // +HE1-
-#define HEATER_2_PIN       PF9   // +HE2-
-#define HEATER_BED_PIN     PA0   // +HOT-BED-
-#define FAN_PIN            PB1   // +FAN-
-
-/**
- * Note: MKS Robin Pro board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
- */
-//#define MAX6675_SS_PIN     PE5   // TC1 - CS1
-//#define MAX6675_SS_PIN     PF11  // TC2 - CS2
-
-#define POWER_LOSS_PIN     PA2   // PW_DET
-#define PS_ON_PIN          PG11   // PW_OFF
-#define FIL_RUNOUT_PIN     PA4  // MT_DET1
-//#define FIL_RUNOUT_PIN     PE6   // MT_DET2
-//#define FIL_RUNOUT_PIN     PG14  // MT_DET3
-
-//
-// SD Card
-//
-#ifndef SDCARD_CONNECTION
-  #define SDCARD_CONNECTION ONBOARD
-#endif
-
-#if SD_CONNECTION_IS(LCD)
-  #define ENABLE_SPI2
-  #define SD_DETECT_PIN    PG3
-  #define SCK_PIN          PB13
-  #define MISO_PIN         PB14
-  #define MOSI_PIN         PB15
-  #define SS_PIN           PG6
-#elif SD_CONNECTION_IS(ONBOARD)
-  #define SDIO_SUPPORT
-  #define SD_DETECT_PIN    PD12
-#elif SD_CONNECTION_IS(CUSTOM_CABLE)
-  #error "No custom SD drive cable defined for this board."
-#endif
-
-/**
- * Note: MKS Robin TFT screens use various TFT controllers.
- * If the screen stays white, disable 'LCD_RESET_PIN'
- * to let the bootloader init the screen.
- */
-#if ENABLED(FSMC_GRAPHICAL_TFT)
-  #define FSMC_CS_PIN      PD7    // NE4
-  #define FSMC_RS_PIN      PD11   // A0
-
-  #define LCD_RESET_PIN    PF6
-  #define NO_LCD_REINIT             // Suppress LCD re-initialization
-
-  #define LCD_BACKLIGHT_PIN PD13
-
-  #if ENABLED(TOUCH_BUTTONS)
-    #define TOUCH_CS_PIN   PA7
-  #else
-    #define BEEPER_PIN     PC5
-    #define BTN_ENC        PG2
-    #define BTN_EN1        PG5
-    #define BTN_EN2        PG4
-  #endif
-
-#elif HAS_SPI_LCD
-
-  #define BEEPER_PIN       PC5
-  #define BTN_ENC          PG2
-  #define LCD_PINS_ENABLE  PG0
-  #define LCD_PINS_RS      PG1
-  #define BTN_EN1          PG5
-  #define BTN_EN2          PG4
-
-  // MKS MINI12864 and MKS LCD12864B. If using MKS LCD12864A (Need to remove RPK2 resistor)
-  #if ENABLED(MKS_MINI_12864)
-
-    #define LCD_BACKLIGHT_PIN -1
-    #define LCD_RESET_PIN  -1
-    #define DOGLCD_A0      PF12
-    #define DOGLCD_CS      PF15
-    #define DOGLCD_SCK     PB13
-    #define DOGLCD_MOSI    PB15
-
-  #else // !MKS_MINI_12864 && !ENDER2_STOCKDISPLAY
-
-    #define LCD_PINS_D4    PF14
-    #if ENABLED(ULTIPANEL)
-      #define LCD_PINS_D5  PF15
-      #define LCD_PINS_D6  PF12
-      #define LCD_PINS_D7  PF13
-    #endif
-
-  #endif // !MKS_MINI_12864 && !ENDER2_STOCKDISPLAY
-#endif
-
-#ifndef ST7920_DELAY_1
-  #define ST7920_DELAY_1 DELAY_NS(125)
-#endif
-#ifndef ST7920_DELAY_2
-  #define ST7920_DELAY_2 DELAY_NS(125)
-#endif
-#ifndef ST7920_DELAY_3
-  #define ST7920_DELAY_3 DELAY_NS(125)
-#endif

Marlin/src/pins/stm32/pins_REMRAM_V1.h

@@ -1,133 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-#ifndef STM32F7xx
-  #error "Oops! Select an STM32F7 board in 'Tools > Board.'"
-#endif
-
-#define BOARD_INFO_NAME      "RemRam v1"
-#define DEFAULT_MACHINE_NAME "RemRam"
-
-#define SRAM_EEPROM_EMULATION // Emulate the EEPROM using Backup SRAM
-
-#if HOTENDS > 1 || E_STEPPERS > 1
-  #error "RemRam supports only one hotend / E-stepper."
-#endif
-
-//
-// Limit Switches
-//
-#if DISABLED(SENSORLESS_HOMING)
-  #define X_MIN_PIN        58
-  #define X_MAX_PIN        59
-  #define Y_MIN_PIN        60
-  #define Y_MAX_PIN        61
-  #define Z_MIN_PIN        62
-  #define Z_MAX_PIN        63
-#else
-  #define X_STOP_PIN       36
-  #define Y_STOP_PIN       39
-  #define Z_MIN_PIN        62
-  #define Z_MAX_PIN        42
-#endif
-
-//
-// Z Probe (when not Z_MIN_PIN)
-//
-#ifndef Z_MIN_PROBE_PIN
-  #define Z_MIN_PROBE_PIN  26   // EXT_D1
-#endif
-
-//
-// Steppers
-//
-#define X_STEP_PIN         22
-#define X_DIR_PIN          35
-#define X_ENABLE_PIN       34
-#define X_CS_PIN           14
-
-#define Y_STEP_PIN         23
-#define Y_DIR_PIN          38
-#define Y_ENABLE_PIN       37
-#define Y_CS_PIN           15
-
-#define Z_STEP_PIN         24
-#define Z_DIR_PIN          41
-#define Z_ENABLE_PIN       40
-#define Z_CS_PIN           16
-
-#define E0_STEP_PIN        25
-#define E0_DIR_PIN         44
-#define E0_ENABLE_PIN      43
-#define E0_CS_PIN          10
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         64   // THERM_1
-#define TEMP_1_PIN         65   // THERM_2
-#define TEMP_BED_PIN       66   // THERM_3
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       33
-#define HEATER_BED_PIN     31
-
-#ifndef FAN_PIN
-  #define FAN_PIN          30   // "FAN1"
-#endif
-#define FAN1_PIN           32   // "FAN2"
-
-#define ORIG_E0_AUTO_FAN_PIN 32   // Use this by NOT overriding E0_AUTO_FAN_PIN
-
-//
-// Servos
-//
-#define SERVO0_PIN         26   // PWM_EXT1
-#define SERVO1_PIN         27   // PWM_EXT2
-
-#define SDSS               57   // Onboard SD card reader
-//#define SDSS              9   // LCD SD card reader
-#define LED_PIN            21   // STATUS_LED
-
-//
-// LCD / Controller
-//
-#define SD_DETECT_PIN      56   // SD_CARD_DET
-#define BEEPER_PIN         46   // LCD_BEEPER
-#define LCD_PINS_RS        49   // LCD_RS
-#define LCD_PINS_ENABLE    48   // LCD_EN
-#define LCD_PINS_D4        50   // LCD_D4
-#define LCD_PINS_D5        51   // LCD_D5
-#define LCD_PINS_D6        52   // LCD_D6
-#define LCD_PINS_D7        53   // LCD_D7
-#define BTN_EN1            54   // BTN_EN1
-#define BTN_EN2            55   // BTN_EN2
-#define BTN_ENC            47   // BTN_ENC
-
-//
-// Timers
-//
-
-#define STEP_TIMER 2

Marlin/src/pins/stm32/pins_RUMBA32_common.h

@@ -1,149 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * Common pin assignments for all RUMBA32 boards
- */
-
-#ifndef STM32F4
-  #error "Oops! Select an STM32F4 board in 'Tools > Board.'"
-#elif HOTENDS > 3 || E_STEPPERS > 3
-  #error "RUMBA32 boards support up to 3 hotends / E-steppers."
-#endif
-
-#define RUMBA32_V1_0
-#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
-
-//#define I2C_EEPROM
-#ifdef E2END
-  #undef E2END
-#endif
-#define E2END 0xFFF // 4KB
-
-//
-// Limit Switches
-//
-#define X_MIN_PIN          PB12
-#define X_MAX_PIN          PB13
-#define Y_MIN_PIN          PB15
-#define Y_MAX_PIN          PD8
-#define Z_MIN_PIN          PD9
-#define Z_MAX_PIN          PD10
-
-//
-// Steppers
-//
-#define X_STEP_PIN         PA0
-#define X_DIR_PIN          PC15
-#define X_ENABLE_PIN       PC11
-#define X_CS_PIN           PC14
-
-#define Y_STEP_PIN         PE5
-#define Y_DIR_PIN          PE6
-#define Y_ENABLE_PIN       PE3
-#define Y_CS_PIN           PE4
-
-#define Z_STEP_PIN         PE1
-#define Z_DIR_PIN          PE2
-#define Z_ENABLE_PIN       PB7
-#define Z_CS_PIN           PE0
-
-#define E0_STEP_PIN        PB5
-#define E0_DIR_PIN         PB6
-#define E0_ENABLE_PIN      PC12
-#define E0_CS_PIN          PC13
-
-#define E1_STEP_PIN        PD6
-#define E1_DIR_PIN         PD7
-#define E1_ENABLE_PIN      PD4
-#define E1_CS_PIN          PD5
-
-#define E2_STEP_PIN        PD2
-#define E2_DIR_PIN         PD3
-#define E2_ENABLE_PIN      PD0
-#define E2_CS_PIN          PD1
-
-//
-// Temperature Sensors
-//
-#define TEMP_0_PIN         PC4
-#define TEMP_1_PIN         PC3
-#define TEMP_2_PIN         PC2
-#define TEMP_3_PIN         PC1
-#define TEMP_BED_PIN       PC0
-
-//
-// Heaters / Fans
-//
-#define HEATER_0_PIN       PC6
-#define HEATER_1_PIN       PC7
-#define HEATER_2_PIN       PC8
-#define HEATER_BED_PIN     PA1
-
-#define FAN_PIN            PC9
-#define FAN1_PIN           PA8
-
-//
-// I2C
-//
-#define SCK_PIN            PA5
-#define MISO_PIN           PA6
-#define MOSI_PIN           PA7
-
-//
-// Misc. Functions
-//
-#define LED_PIN            PB14
-#define BTN_PIN            PC10
-#define PS_ON_PIN          PE11
-#define KILL_PIN           PC5
-
-#define SDSS               PA2
-#define SD_DETECT_PIN      PB0
-#define BEEPER_PIN         PE8
-
-//
-// LCD / Controller
-//
-#if HAS_SPI_LCD
-
-  #define BTN_EN1          PB2
-  #define BTN_EN2          PB1
-  #define BTN_ENC          PE7
-
-  #define LCD_PINS_RS      PE10
-  #define LCD_PINS_ENABLE  PE9
-  #define LCD_PINS_D4      PE12
-
-  #if ENABLED(MKS_MINI_12864)
-    #define DOGLCD_CS      PE13
-    #define DOGLCD_A0      PE14
-  #endif
-
-  #if ENABLED(ULTIPANEL)
-    #define LCD_PINS_D5    PE13
-    #define LCD_PINS_D6    PE14
-    #define LCD_PINS_D7    PE15
-  #endif
-
-#endif