makerbase
4 years ago
committed by
Scott Lahteine
Scott Lahteine
3 changed files with 360 additions and 0 deletions
@ -0,0 +1,357 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
#pragma once |
|||
|
|||
/**
|
|||
* MKS SGen pin assignments |
|||
*/ |
|||
|
|||
#ifndef MCU_LPC1769 |
|||
#error "Oops! Make sure you have the LPC1769 environment selected in your IDE." |
|||
#endif |
|||
|
|||
#define BOARD_INFO_NAME "MKS SGEN_L V2" |
|||
#define BOARD_WEBSITE_URL "github.com/makerbase-mks" |
|||
|
|||
//
|
|||
// EEPROM, MKS SGEN_L V2.0 hardware has 4K EEPROM on the board
|
|||
//
|
|||
#if NO_EEPROM_SELECTED |
|||
//#define SDCARD_EEPROM_EMULATION
|
|||
//#define I2C_EEPROM // AT24C32
|
|||
#define FLASH_EEPROM_EMULATION |
|||
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
|||
#endif |
|||
|
|||
//
|
|||
// Servos
|
|||
//
|
|||
#define SERVO0_PIN P1_23 // SERVO P1.23
|
|||
#define SERVO1_PIN P2_00 // SERVO P2.0
|
|||
|
|||
//
|
|||
// Trinamic Stallguard pins, can connect or disconnect by jumpers cap on the board
|
|||
//
|
|||
#define X_DIAG_PIN P1_29 // X-
|
|||
#define Y_DIAG_PIN P1_27 // Y-
|
|||
#define Z_DIAG_PIN P1_25 // Z-
|
|||
#define E0_DIAG_PIN P1_28 // X+
|
|||
#define E1_DIAG_PIN P1_26 // Y+
|
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#if X_STALL_SENSITIVITY |
|||
#define X_STOP_PIN X_DIAG_PIN |
|||
#if X_HOME_DIR < 0 |
|||
#define X_MAX_PIN P1_28 // X+
|
|||
#else |
|||
#define X_MIN_PIN P1_28 // X+
|
|||
#endif |
|||
#else |
|||
#define X_MIN_PIN P1_29 // X-
|
|||
#define X_MAX_PIN P1_28 // X+
|
|||
#endif |
|||
|
|||
#if Y_STALL_SENSITIVITY |
|||
#define Y_STOP_PIN Y_DIAG_PIN |
|||
#if Y_HOME_DIR < 0 |
|||
#define Y_MAX_PIN P1_26 // Y+
|
|||
#else |
|||
#define Y_MIN_PIN P1_26 // Y+
|
|||
#endif |
|||
#else |
|||
#define Y_MIN_PIN P1_27 // Y-
|
|||
#define Y_MAX_PIN P1_26 // Y+
|
|||
#endif |
|||
|
|||
#if Z_STALL_SENSITIVITY |
|||
#define Z_STOP_PIN Z_DIAG_PIN |
|||
#if Z_HOME_DIR < 0 |
|||
#define Z_MAX_PIN P1_24 // Z+
|
|||
#else |
|||
#define Z_MIN_PIN P1_24 // Z+
|
|||
#endif |
|||
#else |
|||
#define Z_MIN_PIN P1_25 // Z-
|
|||
#define Z_MAX_PIN P1_24 // Z+
|
|||
#endif |
|||
|
|||
//
|
|||
// Z Probe (when not Z_MIN_PIN)
|
|||
//
|
|||
#ifndef Z_MIN_PROBE_PIN |
|||
#define Z_MIN_PROBE_PIN P1_24 |
|||
#endif |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_STEP_PIN P2_02 |
|||
#define X_DIR_PIN P2_03 |
|||
#define X_ENABLE_PIN P2_01 |
|||
#ifndef X_CS_PIN |
|||
#define X_CS_PIN P1_01 |
|||
#endif |
|||
|
|||
#define Y_STEP_PIN P0_19 |
|||
#define Y_DIR_PIN P0_20 |
|||
#define Y_ENABLE_PIN P2_08 |
|||
#ifndef Y_CS_PIN |
|||
#define Y_CS_PIN P1_08 |
|||
#endif |
|||
|
|||
#define Z_STEP_PIN P0_22 |
|||
#define Z_DIR_PIN P2_11 |
|||
#define Z_ENABLE_PIN P0_21 |
|||
#ifndef Z_CS_PIN |
|||
#define Z_CS_PIN P1_10 |
|||
#endif |
|||
|
|||
#define E0_STEP_PIN P2_13 |
|||
#define E0_DIR_PIN P0_11 |
|||
#define E0_ENABLE_PIN P2_12 |
|||
#ifndef E0_CS_PIN |
|||
#define E0_CS_PIN P1_15 |
|||
#endif |
|||
|
|||
#define E1_STEP_PIN P1_09 |
|||
#define E1_DIR_PIN P1_14 |
|||
#define E1_ENABLE_PIN P0_10 |
|||
#ifndef E1_CS_PIN |
|||
#define E1_CS_PIN P1_17 |
|||
#endif |
|||
|
|||
//
|
|||
// Software SPI pins for TMC2130 stepper drivers
|
|||
//
|
|||
#if ENABLED(TMC_USE_SW_SPI) |
|||
#ifndef TMC_SW_MOSI |
|||
#define TMC_SW_MOSI P1_16 |
|||
#endif |
|||
#ifndef TMC_SW_MISO |
|||
#define TMC_SW_MISO P0_05 |
|||
#endif |
|||
#ifndef TMC_SW_SCK |
|||
#define TMC_SW_SCK P0_04 |
|||
#endif |
|||
#endif |
|||
|
|||
#if HAS_TMC_UART |
|||
/**
|
|||
* TMC2208/TMC2209 stepper drivers |
|||
* |
|||
* Hardware serial communication ports. |
|||
* If undefined software serial is used according to the pins below |
|||
*/ |
|||
//#define X_HARDWARE_SERIAL Serial
|
|||
//#define X2_HARDWARE_SERIAL Serial1
|
|||
//#define Y_HARDWARE_SERIAL Serial1
|
|||
//#define Y2_HARDWARE_SERIAL Serial1
|
|||
//#define Z_HARDWARE_SERIAL Serial1
|
|||
//#define Z2_HARDWARE_SERIAL Serial1
|
|||
//#define E0_HARDWARE_SERIAL Serial1
|
|||
//#define E1_HARDWARE_SERIAL Serial1
|
|||
//#define E2_HARDWARE_SERIAL Serial1
|
|||
//#define E3_HARDWARE_SERIAL Serial1
|
|||
//#define E4_HARDWARE_SERIAL Serial1
|
|||
|
|||
//
|
|||
// Software serial
|
|||
//
|
|||
#define X_SERIAL_TX_PIN P1_01 |
|||
#define X_SERIAL_RX_PIN P1_01 |
|||
#define Y_SERIAL_TX_PIN P1_08 |
|||
#define Y_SERIAL_RX_PIN P1_08 |
|||
#define Z_SERIAL_TX_PIN P1_10 |
|||
#define Z_SERIAL_RX_PIN P1_10 |
|||
#define E0_SERIAL_TX_PIN P1_15 |
|||
#define E0_SERIAL_RX_PIN P1_15 |
|||
#define E1_SERIAL_TX_PIN P1_17 |
|||
#define E1_SERIAL_RX_PIN P1_17 |
|||
|
|||
// Reduce baud rate to improve software serial reliability
|
|||
#define TMC_BAUD_RATE 19200 |
|||
#endif // HAS_TMC_UART
|
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
// 3.3V max when defined as an analog input
|
|||
//
|
|||
#define TEMP_0_PIN P0_23_A0 // Analog Input A0 (TH1)
|
|||
#define TEMP_BED_PIN P0_24_A1 // Analog Input A1 (TB)
|
|||
#define TEMP_1_PIN P0_25_A2 // Analog Input A2 (TH2)
|
|||
#define TEMP_2_PIN P0_26_A3 // Analog Input A3 (P0.26, No pull up)
|
|||
|
|||
//
|
|||
// Heaters / Fans
|
|||
//
|
|||
#define HEATER_BED_PIN P2_05 |
|||
#define HEATER_0_PIN P2_07 |
|||
#if HOTENDS == 1 |
|||
#ifndef FAN1_PIN |
|||
#define FAN1_PIN P2_06 |
|||
#endif |
|||
#else |
|||
#ifndef HEATER_1_PIN |
|||
#define HEATER_1_PIN P2_06 |
|||
#endif |
|||
#endif |
|||
#ifndef FAN_PIN |
|||
#define FAN_PIN P2_04 |
|||
#endif |
|||
#ifndef FAN2_PIN |
|||
#define FAN2_PIN P1_04 |
|||
#endif |
|||
|
|||
//
|
|||
// Misc. Functions
|
|||
//
|
|||
#define LED_PIN P1_18 // Used as a status indicator
|
|||
#define LED2_PIN P1_19 |
|||
#define LED3_PIN P1_20 |
|||
#define LED4_PIN P1_21 |
|||
|
|||
/**
|
|||
* _____ _____ |
|||
* (BEEPER) 1.31 | · · | 1.30 (BTN_ENC) (MISO) 0.8 | · · | 0.7 (SD_SCK) |
|||
* (LCD_EN) 0.18 | · · | 0.16 (LCD_RS) (BTN_EN1) 3.25 | · · | 0.28 (SD_CS2) |
|||
* (LCD_D4) 0.15 | · ·| 0.17 (LCD_D5) (BTN_EN2) 3.26 | · ·| 0.9 (SD_MOSI) |
|||
* (LCD_D6) 1.0 | · · | 1.22 (LCD_D7) (SD_DETECT) 0.27 | · · | RST |
|||
* GND | · · | 5V GND | · · | NC |
|||
* ----- ----- |
|||
* EXP1 EXP2 |
|||
*/ |
|||
#if HAS_SPI_LCD |
|||
#define BEEPER_PIN P1_31 |
|||
#define BTN_ENC P1_30 |
|||
|
|||
#if ENABLED(CR10_STOCKDISPLAY) |
|||
#define LCD_PINS_RS P1_00 |
|||
|
|||
#define BTN_EN1 P0_18 |
|||
#define BTN_EN2 P0_15 |
|||
|
|||
#define LCD_PINS_ENABLE P1_22 |
|||
#define LCD_PINS_D4 P0_17 |
|||
|
|||
#else |
|||
|
|||
#define BTN_EN1 P3_25 |
|||
#define BTN_EN2 P3_26 |
|||
|
|||
#define LCD_SDSS P0_28 |
|||
|
|||
#if ENABLED(MKS_12864OLED_SSD1306) |
|||
|
|||
#define LCD_PINS_DC P0_17 |
|||
#define DOGLCD_CS P0_16 |
|||
#define DOGLCD_A0 LCD_PINS_DC |
|||
#define DOGLCD_SCK P0_15 |
|||
#define DOGLCD_MOSI P0_18 |
|||
|
|||
#define LCD_PINS_RS P1_00 |
|||
#define LCD_PINS_D7 P1_22 |
|||
#define KILL_PIN -1 // NC
|
|||
|
|||
#else // !MKS_12864OLED_SSD1306
|
|||
|
|||
#define LCD_PINS_RS P0_16 |
|||
|
|||
#define LCD_PINS_ENABLE P0_18 |
|||
#define LCD_PINS_D4 P0_15 |
|||
|
|||
#if ENABLED(FYSETC_MINI_12864) |
|||
|
|||
#define DOGLCD_CS P0_18 |
|||
#define DOGLCD_A0 P0_16 |
|||
#define DOGLCD_SCK P0_07 |
|||
#define DOGLCD_MOSI P1_20 |
|||
|
|||
#define LCD_BACKLIGHT_PIN -1 |
|||
|
|||
#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
|||
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
|||
|
|||
#define LCD_RESET_PIN P0_15 // Must be high or open for LCD to operate normally.
|
|||
|
|||
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) |
|||
#ifndef RGB_LED_R_PIN |
|||
#define RGB_LED_R_PIN P0_17 |
|||
#endif |
|||
#ifndef RGB_LED_G_PIN |
|||
#define RGB_LED_G_PIN P1_00 |
|||
#endif |
|||
#ifndef RGB_LED_B_PIN |
|||
#define RGB_LED_B_PIN P1_22 |
|||
#endif |
|||
#elif ENABLED(FYSETC_MINI_12864_2_1) |
|||
#define NEOPIXEL_PIN P0_17 |
|||
#endif |
|||
|
|||
#else // !FYSETC_MINI_12864
|
|||
|
|||
#if ENABLED(MKS_MINI_12864) |
|||
#define DOGLCD_CS P0_17 |
|||
#define DOGLCD_A0 P1_00 |
|||
#endif |
|||
|
|||
#if ENABLED(ULTIPANEL) |
|||
#define LCD_PINS_D5 P0_17 |
|||
#define LCD_PINS_D6 P1_00 |
|||
#define LCD_PINS_D7 P1_22 |
|||
#endif |
|||
|
|||
#endif // !FYSETC_MINI_12864
|
|||
|
|||
#endif // !MKS_12864OLED_SSD1306
|
|||
|
|||
#endif // !CR10_STOCKDISPLAY
|
|||
|
|||
#endif // HAS_SPI_LCD
|
|||
|
|||
#ifndef SDCARD_CONNECTION |
|||
#define SDCARD_CONNECTION ONBOARD |
|||
#endif |
|||
|
|||
#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card
|
|||
|
|||
#if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) |
|||
#define SD_DETECT_PIN P0_27 |
|||
#define SCK_PIN P0_07 |
|||
#define MISO_PIN P0_08 |
|||
#define MOSI_PIN P0_09 |
|||
#if SD_CONNECTION_IS(ONBOARD) |
|||
#define SS_PIN ONBOARD_SD_CS_PIN |
|||
#else |
|||
#define SS_PIN P0_28 |
|||
#endif |
|||
#elif SD_CONNECTION_IS(CUSTOM_CABLE) |
|||
#error "No custom SD drive cable defined for this board." |
|||
#endif |
|||
|
|||
//
|
|||
// Other Pins
|
|||
//
|
|||
//#define PIN_P0_02 P0_02 // AUX1 (Interrupt Capable/ADC/Serial Port 0)
|
|||
//#define PIN_P0_03 P0_03 // AUX1 (Interrupt Capable/ADC/Serial Port 0)
|
|||
//#define PS_ON_PIN P1_23 // SERVO P1.23
|
|||
Loading…
Reference in new issue