// and processor overload (too many expensive sqrt calls).
#define DELTA_SEGMENTS_PER_SECOND 160
// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
// Center-to-center distance of the holes in the diagonal push rods.
#define DELTA_DIAGONAL_ROD 218.0 // mm
/*
// Horizontal offset from middle of printer to smooth rod center.
//#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm
#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm
// Horizontal offset of the universal joints on the end effector.
//#define DELTA_EFFECTOR_OFFSET 24.0 // mm
#define DELTA_EFFECTOR_OFFSET 24.0 // mm
// Horizontal offset of the universal joints on the carriages.
//#define DELTA_CARRIAGE_OFFSET 22.0 // mm
#define DELTA_CARRIAGE_OFFSET 22.0 // mm
*/
// Horizontal distance bridged by diagonal push rods when effector is centered.
#define DELTA_RADIUS 100.90 //mm // get this value from auto calibrate
#define DELTA_RADIUS 100.00 //mm // get this value from auto calibrate
// height from z=0.00 to home position
#define DELTA_HEIGHT 296.38// get this value from auto calibrate
#define DELTA_HEIGHT 295.00// get this value from auto calibrate - use G33 C-1 at 1st time calibration
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
#define DELTA_PRINTABLE_RADIUS 85.0
// Delta calibration menu
// uncomment to add three points calibration menu option.
// See http://minow.blogspot.com/index.html#4918805519571907051
#define DELTA_CALIBRATION_MENU
@ -477,7 +480,7 @@
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
#define DELTA_AUTO_CALIBRATION
#if ENABLED(DELTA_AUTO_CALIBRATION)
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-2,1-7)
#define DELTA_CALIBRATION_DEFAULT_POINTS 4 // set the default number of probe points : n*n (-7 -> +7)
#endif
// After homing move down to a height where XY movement is unconstrained
@ -529,7 +532,7 @@
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
@ -601,7 +604,7 @@
#define DEFAULT_XJERK 20.0
#define DEFAULT_YJERK DEFAULT_XJERK
#define DEFAULT_ZJERK DEFAULT_YJERK // Must be same as XY for delta
#define DEFAULT_EJERK 5.0
#define DEFAULT_EJERK 5.0
/**
@ -667,9 +670,6 @@
*isenabledthenitalsoappliestoZ_PROBE_SPEED_SLOW.
*/
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define Z_PROBE_SLED
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -694,8 +694,8 @@
*(0,0)
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25// Z offset: -below +above [the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10// Z offset: -below +above [the nozzle]
// X and Y axis travel speed (mm/m) between probes
LVD-AC
8 years ago
teemuatlut