Simplify power supply naming logic (#14488)

Co-Authored-By: Tim Moore <tim.moore@lightbend.com>
Co-Authored-By: AnHardt <github@kitelab.de>

Marlin/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

Marlin/src/Marlin.h

@@ -349,8 +349,8 @@ extern millis_t max_inactive_time, stepper_inactive_time;
 
 #if HAS_POWER_SWITCH
   extern bool powersupply_on;
-  #define PSU_PIN_ON()  do{ OUT_WRITE(PS_ON_PIN, PS_ON_AWAKE); powersupply_on = true; }while(0)
-  #define PSU_PIN_OFF() do{ OUT_WRITE(PS_ON_PIN, PS_ON_ASLEEP); powersupply_on = false; }while(0)
+  #define PSU_PIN_ON()  do{ OUT_WRITE(PS_ON_PIN,  PSU_ACTIVE_HIGH); powersupply_on = true; }while(0)
+  #define PSU_PIN_OFF() do{ OUT_WRITE(PS_ON_PIN, !PSU_ACTIVE_HIGH); powersupply_on = false; }while(0)
   #if ENABLED(AUTO_POWER_CONTROL)
     #define PSU_ON()  powerManager.power_on()
     #define PSU_OFF() powerManager.power_off()

Marlin/src/gcode/gcode.h

@@ -111,8 +111,8 @@
  * M76  - Pause the print job timer.
  * M77  - Stop the print job timer.
  * M78  - Show statistical information about the print jobs. (Requires PRINTCOUNTER)
- * M80  - Turn on Power Supply. (Requires POWER_SUPPLY > 0)
- * M81  - Turn off Power Supply. (Requires POWER_SUPPLY > 0)
+ * M80  - Turn on Power Supply. (Requires PSU_CONTROL)
+ * M81  - Turn off Power Supply. (Requires PSU_CONTROL)
  * M82  - Set E codes absolute (default).
  * M83  - Set E codes relative while in Absolute (G90) mode.
  * M84  - Disable steppers until next move, or use S<seconds> to specify an idle

Marlin/src/inc/Conditionals_LCD.h

@@ -148,7 +148,7 @@
   #define LCD_CONTRAST_MAX 255
   #define DEFAULT_LCD_CONTRAST 220
   #define LED_COLORS_REDUCE_GREEN
-  #if POWER_SUPPLY > 0 && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)
+  #if (HAS_POWER_SWITCH && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1))
     #define LED_BACKLIGHT_TIMEOUT 10000
   #endif
 

Marlin/src/inc/Conditionals_post.h

@@ -269,19 +269,22 @@
   #define DISABLE_INACTIVE_E DISABLE_E
 #endif
 
-// Power Signal Control Definitions
-// By default use ATX definition
-#ifndef POWER_SUPPLY
-  #define POWER_SUPPLY 1
-#endif
-#if (POWER_SUPPLY == 1)     // 1 = ATX
-  #define PS_ON_AWAKE  LOW
-  #define PS_ON_ASLEEP HIGH
-#elif (POWER_SUPPLY == 2)   // 2 = X-Box 360 203W
-  #define PS_ON_AWAKE  HIGH
-  #define PS_ON_ASLEEP LOW
-#endif
-#define HAS_POWER_SWITCH (POWER_SUPPLY > 0 && PIN_EXISTS(PS_ON))
+/**
+ * Power Supply Control
+ */
+#ifndef PSU_NAME
+  #if ENABLED(PSU_CONTROL)
+    #if PSU_ACTIVE_HIGH
+      #define PSU_NAME "XBox"     // X-Box 360 (203W)
+    #else
+      #define PSU_NAME "ATX"      // ATX style
+    #endif
+  #else
+    #define PSU_NAME "Generic"    // No control
+  #endif
+#endif
+
+#define HAS_POWER_SWITCH (ENABLED(PSU_CONTROL) && PIN_EXISTS(PS_ON))
 
 /**
  * Temp Sensor defines

Marlin/src/inc/SanityCheck.h

@@ -376,6 +376,12 @@
   #error "USB_SD_DISABLED is now NO_SD_HOST_DRIVE. Please update your Configuration_adv.h."
 #elif defined(USB_SD_ONBOARD)
   #error "USB_SD_ONBOARD is obsolete. Disable NO_SD_HOST_DRIVE instead."
+#elif POWER_SUPPLY == 1
+  #error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'false'."
+#elif POWER_SUPPLY == 2
+  #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'true'."
+#elif defined(POWER_SUPPLY)
+  #error "POWER_SUPPLY is now obsolete. Please remove it from Configuration.h."
 #endif
 
 #define BOARD_MKS_13     -47
@@ -1548,7 +1554,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * LED Backlight Timeout
  */
-#if defined(LED_BACKLIGHT_TIMEOUT) && !(EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && POWER_SUPPLY > 0)
+#if defined(LED_BACKLIGHT_TIMEOUT) && !(EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && HAS_POWER_SWITCH)
   #error "LED_BACKLIGHT_TIMEOUT requires a Fysetc Mini Panel and a Power Switch."
 #endif
 
@@ -2297,6 +2303,13 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
   #endif
 #endif
 
+/**
+ * Ensure this option is set intentionally
+ */
+#if ENABLED(PSU_CONTROL) && !defined(PSU_ACTIVE_HIGH)
+  #error "PSU_CONTROL requires PSU_ACTIVE_HIGH to be defined as 'true' or 'false'."
+#endif
+
 #if HAS_CUTTER
   #define _PIN_CONFLICT(P) (PIN_EXISTS(P) && P##_PIN == SPINDLE_LASER_PWM_PIN)
   #if BOTH(SPINDLE_FEATURE, LASER_FEATURE)

Marlin/src/lcd/menu/menu_info.cpp

@@ -176,13 +176,7 @@ void menu_info_board() {
   STATIC_ITEM(BOARD_NAME, true, true);                           // MyPrinterController
   STATIC_ITEM(MSG_INFO_BAUDRATE ": " STRINGIFY(BAUDRATE), true); // Baud: 250000
   STATIC_ITEM(MSG_INFO_PROTOCOL ": " PROTOCOL_VERSION, true);    // Protocol: 1.0
-  #if POWER_SUPPLY == 0
-    STATIC_ITEM(MSG_INFO_PSU ": Generic", true);
-  #elif POWER_SUPPLY == 1
-    STATIC_ITEM(MSG_INFO_PSU ": ATX", true);  // Power Supply: ATX
-  #elif POWER_SUPPLY == 2
-    STATIC_ITEM(MSG_INFO_PSU ": XBox", true); // Power Supply: XBox
-  #endif
+  STATIC_ITEM(MSG_INFO_PSU ": " PSU_NAME, true);
   END_SCREEN();
 }
 

Marlin/src/pins/pins.h

@@ -741,7 +741,7 @@
 #ifndef LED_PIN
   #define LED_PIN -1
 #endif
-#if POWER_SUPPLY == 0 || !defined(PS_ON_PIN)
+#if DISABLED(PSU_CONTROL) || !defined(PS_ON_PIN)
   #undef PS_ON_PIN
   #define PS_ON_PIN -1
 #endif

Marlin/src/pins/pins_MKS_GEN_13.h

@@ -44,9 +44,9 @@
 //
 // PSU / SERVO
 //
-// If POWER_SUPPLY is specified, always hijack Servo 3
+// If PSU_CONTROL is specified, always hijack Servo 3
 //
-#if POWER_SUPPLY > 0
+#if ENABLED(PSU_CONTROL)
   #define SERVO3_PIN       -1
   #define PS_ON_PIN         4
 #endif

buildroot/share/tests/megaatmega2560-tests

@@ -27,7 +27,6 @@ opt_set EXTRUDERS 2
 opt_set TEMP_SENSOR_0 -2
 opt_set TEMP_SENSOR_1 1
 opt_set TEMP_SENSOR_BED 2
-opt_set POWER_SUPPLY 1
 opt_set GRID_MAX_POINTS_X 16
 opt_set FANMUX0_PIN 53
 opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING EEPROM_SETTINGS \
@@ -37,7 +36,7 @@ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING EEPROM_SETTINGS \
            AUTO_BED_LEVELING_LINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
            SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE \
            FWRETRACT ARC_P_CIRCLES ADVANCED_PAUSE_FEATURE CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS \
-           AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE \
+           PSU_CONTROL AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE \
            LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST PINS_DEBUGGING \
            MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE
 opt_enable SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER

config/default/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/AliExpress/CL-260/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/A2/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/A2plus/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/A6/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/A8/Configuration.h

@@ -313,22 +313,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -338,7 +336,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/A8plus/Configuration.h

@@ -313,22 +313,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -338,7 +336,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Anet/E16/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/AnyCubic/i3/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/ArmEd/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Azteeg/X5GT/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/BIBO/TouchX/default/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/BQ/Hephestos/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/BQ/Hephestos_2/Configuration.h

@@ -320,22 +320,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -345,7 +343,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/BQ/WITBOX/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Cartesio/Configuration.h

@@ -313,22 +313,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -338,7 +336,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-10/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-10S/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-10_5S/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-10mini/Configuration.h

@@ -321,22 +321,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -346,7 +344,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-20/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/CR-8/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/Ender-2/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/Ender-3/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/Ender-4/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Creality/Ender-5/Configuration.h

@@ -312,30 +312,29 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
     #define AUTO_POWER_CONTROLLERFAN
     #define AUTO_POWER_CHAMBER_FAN
+    //#define AUTO_POWER_E_TEMP        50 // (°C) Turn on PSU over this temperature
+    //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Dagoma/Disco Ultimate/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Einstart-S/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Felix/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  #define PS_DEFAULT_OFF
+  #define PS_DEFAULT_OFF        // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Felix/DUAL/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  #define PS_DEFAULT_OFF
+  #define PS_DEFAULT_OFF        // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Formbot/Raptor/Configuration.h

@@ -353,22 +353,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -378,7 +376,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -321,22 +321,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -346,7 +344,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -316,22 +316,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -341,7 +339,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Fysetc/AIO_II/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Fysetc/CHEETAH/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Fysetc/F6_13/Configuration.h

@@ -314,22 +314,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -339,7 +337,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/A10/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/A10M/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/A20M/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/GT2560/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Infitary/i3-M508/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/JGAurora/A1/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/JGAurora/A5/Configuration.h

@@ -317,22 +317,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -342,7 +340,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/JGAurora/A5S/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/MakerParts/Configuration.h

@@ -332,22 +332,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -357,7 +355,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Malyan/M150/Configuration.h

@@ -317,22 +317,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -342,7 +340,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Malyan/M200/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Micromake/C1/basic/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Mks/Robin/Configuration.h

@@ -313,22 +313,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -338,7 +336,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Mks/Sbase/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-#define PS_DEFAULT_OFF
+  #define PS_DEFAULT_OFF        // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -313,22 +313,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -338,7 +336,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/RapideLite/RL200/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/RepRapPro/Huxley/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/RigidBot/Configuration.h

@@ -315,22 +315,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -340,7 +338,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/SCARA/Configuration.h

@@ -339,22 +339,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -364,7 +362,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/STM32/STM32F10/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/STM32/STM32F4/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Sanguinololu/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tevo/Tarantula Pro/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/TheBorg/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/TinyBoy2/Configuration.h

@@ -334,22 +334,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -359,7 +357,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tronxy/X1/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tronxy/X3A/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -314,22 +314,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -339,7 +337,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tronxy/X5S/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Tronxy/XY100/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/UltiMachine/Archim1/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/UltiMachine/Archim2/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/VORONDesign/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Velleman/K8200/Configuration.h

@@ -332,22 +332,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -357,7 +355,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Velleman/K8400/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature

config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 1
+#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature