Browse Source

support for GEN7 1.1,1.2 and 1.3

pull/1/head
Christian Thalhammer 13 years ago
parent
commit
e661578c84
  1. 12
      Marlin/Configuration.h
  2. 76
      Marlin/pins.h

12
Marlin/Configuration.h

@ -9,7 +9,7 @@
//Implementation of an idea by Prof Braino to inform user that any changes made //Implementation of an idea by Prof Braino to inform user that any changes made
//to THIS file by the user have been successfully uploaded into firmware. //to THIS file by the user have been successfully uploaded into firmware.
#define STRING_VERSION_CONFIG_H "2012-02-08j" //Personal revision number for changes to THIS file. #define STRING_VERSION_CONFIG_H "2012-02-08j" //Personal revision number for changes to THIS file.
#define STRING_CONFIG_H_AUTHOR "username" //Who made the changes. #define STRING_CONFIG_H_AUTHOR "scuba82" //Who made the changes.
// This determines the communication speed of the printer // This determines the communication speed of the printer
//#define BAUDRATE 250000 //#define BAUDRATE 250000
@ -21,7 +21,9 @@
// Gen6 = 5, // Gen6 = 5,
// Sanguinololu 1.2 and above = 62 // Sanguinololu 1.2 and above = 62
// Ultimaker = 7, // Ultimaker = 7,
// Gen7 = 77, // Gen7 custom (Alfons3 Version) = 77, "https://github.com/Alfons3/Generation_7_Electronics"
// Gen7 v1.1, v1.2 = 78
// Gen7 v1.3 = 79
// Teensylu = 8, // Teensylu = 8,
// Gen3+ =9 // Gen3+ =9
#define MOTHERBOARD 77 #define MOTHERBOARD 77
@ -49,7 +51,7 @@
// Actual temperature must be close to target for this long before M109 returns success // Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30 // (seconds) #define TEMP_RESIDENCY_TIME 30 // (seconds)
#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (C) range of +/- temperatures considered "close" to the target one
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken. // to check that the wiring to the thermistor is not broken.
@ -127,7 +129,7 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true #define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
@ -138,7 +140,7 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true //If true, axis won't move to coordinates less than zero. #define min_software_endstops false //If true, axis won't move to coordinates less than zero.
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 205 #define X_MAX_LENGTH 205
#define Y_MAX_LENGTH 205 #define Y_MAX_LENGTH 205

76
Marlin/pins.h

@ -567,6 +567,82 @@
#endif #endif
/****************************************************************************************
* Gen7 v1.1, v1.2, v1.3 pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 79
#define MOTHERBOARD 78
#define GEN7_V_1_3
#endif
#if MOTHERBOARD == 78
#define KNOWN_BOARD
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
#error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
#endif
//x axis pins
#define X_STEP_PIN 19
#define X_DIR_PIN 18
#define X_ENABLE_PIN 24
#define X_MIN_PIN 7
#define X_MAX_PIN -1
//y axis pins
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_MIN_PIN 5
#define Y_MAX_PIN -1
//z axis pins
#define Z_STEP_PIN 26
#define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24
#define Z_MIN_PIN 1
#define Z_MAX_PIN -1
//extruder pins
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24
#define TEMP_0_PIN 1
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 2
#define HEATER_0_PIN 4
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 3
#define SDPOWER -1
#define SDSS -1 // SCL pin of I2C header
#define LED_PIN -1
#ifdef GEN7_V_1_3
// Gen7 v1.3 removed the fan pin
#define FAN_PIN -1
#else
#define FAN_PIN 31
#endif
#define PS_ON_PIN 15
//our pin for debugging.
#define DEBUG_PIN 0
//our RS485 pins
#define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13
#endif
/******************************************************************************* /*******************************************************************************
********* *********
* Gen7 Alfons3 pin assignment * Gen7 Alfons3 pin assignment

Loading…
Cancel
Save