Browse Source

Merge pull request #2115 from AnHardt/_temp_error

Use _temp_error() for all errors thrown by different heater sanity check mechanisms
pull/1/head
AnHardt 10 years ago
parent
commit
d6c1285ab5
  1. 17
      Marlin/language.h
  2. 29
      Marlin/temperature.cpp

17
Marlin/language.h

@ -223,15 +223,16 @@
#define MSG_PID_DEBUG_PTERM " pTerm "
#define MSG_PID_DEBUG_ITERM " iTerm "
#define MSG_PID_DEBUG_DTERM " dTerm "
#define MSG_HEATING_FAILED "Heating failed"
#define MSG_EXTRUDER_SWITCHED_OFF "Extruder switched off. Temperature difference between temp sensors is too high !"
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !"
#define MSG_THERMAL_RUNAWAY_STOP "Thermal Runaway, system stopped! Heater_ID: "
#define MSG_SWITCHED_OFF_MAX " switched off. MAXTEMP triggered !!"
#define MSG_MINTEMP_EXTRUDER_OFF ": Extruder switched off. MINTEMP triggered !"
#define MSG_MAXTEMP_EXTRUDER_OFF ": Extruder" MSG_SWITCHED_OFF_MAX
#define MSG_MAXTEMP_BED_OFF "Heated bed" MSG_SWITCHED_OFF_MAX
#define MSG_HEATER_BED "bed"
#define MSG_STOPPED_HEATER ", system stopped! Heater_ID: "
#define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !"
#define MSG_T_HEATING_FAILED "Heating failed"
#define MSG_T_THERMAL_RUNAWAY "Thermal Runaway"
#define MSG_T_MAXTEMP "MAXTEMP triggered"
#define MSG_T_MINTEMP "MINTEMP triggered"
// LCD Menu Messages

29
Marlin/temperature.cpp

@ -450,31 +450,28 @@ void checkExtruderAutoFans()
inline void _temp_error(int e, const char *serial_msg, const char *lcd_msg) {
if (IsRunning()) {
SERIAL_ERROR_START;
if (e >= 0) SERIAL_ERRORLN((int)e);
serialprintPGM(serial_msg);
MYSERIAL.write('\n');
#ifdef ULTRA_LCD
lcd_setalertstatuspgm(lcd_msg);
#endif
SERIAL_ERRORPGM(MSG_STOPPED_HEATER);
if (e >= 0) SERIAL_ERRORLN((int)e); else SERIAL_ERRORLNPGM(MSG_HEATER_BED);
}
#ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
Stop();
kill(lcd_msg);
#endif
}
void max_temp_error(uint8_t e) {
disable_all_heaters();
_temp_error(e, PSTR(MSG_MAXTEMP_EXTRUDER_OFF), PSTR(MSG_ERR_MAXTEMP));
_temp_error(e, PSTR(MSG_T_MAXTEMP), PSTR(MSG_ERR_MAXTEMP));
}
void min_temp_error(uint8_t e) {
disable_all_heaters();
_temp_error(e, PSTR(MSG_MINTEMP_EXTRUDER_OFF), PSTR(MSG_ERR_MINTEMP));
_temp_error(e, PSTR(MSG_T_MINTEMP), PSTR(MSG_ERR_MINTEMP));
}
void bed_max_temp_error(void) {
#if HAS_HEATER_BED
WRITE_HEATER_BED(0);
#endif
_temp_error(-1, PSTR(MSG_MAXTEMP_BED_OFF), PSTR(MSG_ERR_MAXTEMP_BED));
_temp_error(-1, PSTR(MSG_T_MAXTEMP), PSTR(MSG_ERR_MAXTEMP_BED));
}
float get_pid_output(int e) {
@ -628,8 +625,7 @@ void manage_heater() {
// Has it failed to increase enough?
if (degHotend(e) < watch_target_temp[e]) {
// Stop!
disable_all_heaters();
_temp_error(e, PSTR(MSG_HEATING_FAILED), PSTR(MSG_HEATING_FAILED_LCD));
_temp_error(e, PSTR(MSG_T_HEATING_FAILED), PSTR(MSG_HEATING_FAILED_LCD));
}
else {
// Start again if the target is still far off
@ -1071,16 +1067,7 @@ void tp_init() {
*state = TRRunaway;
break;
case TRRunaway:
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM(MSG_THERMAL_RUNAWAY_STOP);
if (heater_id < 0) SERIAL_ERRORLNPGM("bed"); else SERIAL_ERRORLN(heater_id);
LCD_ALERTMESSAGEPGM(MSG_THERMAL_RUNAWAY);
disable_all_heaters();
disable_all_steppers();
for (;;) {
manage_heater();
lcd_update();
}
_temp_error(heater_id, PSTR(MSG_T_THERMAL_RUNAWAY), PSTR(MSG_THERMAL_RUNAWAY));
}
}

Loading…
Cancel
Save