George Fu
5 years ago
committed by
Scott Lahteine
Scott Lahteine
13 changed files with 6392 additions and 4 deletions
@ -0,0 +1,234 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
#pragma once |
|||
|
|||
#ifndef STM32F4 |
|||
#error "Oops! Select an STM32F4 board in 'Tools > Board.'" |
|||
#elif HOTENDS > 3 || E_STEPPERS > 3 |
|||
#error "RUMBA32 supports up to 3 hotends / E-steppers." |
|||
#endif |
|||
|
|||
#ifndef BOARD_INFO_NAME |
|||
#define BOARD_INFO_NAME "FYSETC_S6" |
|||
#endif |
|||
#ifndef DEFAULT_MACHINE_NAME |
|||
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME |
|||
#endif |
|||
|
|||
// change the prio to 3 , 2 is for software serial
|
|||
//#define TEMP_TIMER_IRQ_PRIO 3
|
|||
|
|||
//
|
|||
// EEPROM Emulation
|
|||
//
|
|||
#define FLASH_EEPROM_EMULATION |
|||
//#define SRAM_EEPROM_EMULATION
|
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#define X_MIN_PIN PB14 |
|||
#define X_MAX_PIN PA1 |
|||
#define Y_MIN_PIN PB13 |
|||
#define Y_MAX_PIN PA2 |
|||
#define Z_MIN_PIN PA0 |
|||
#define Z_MAX_PIN PA3 |
|||
|
|||
//
|
|||
// Servos
|
|||
// share with Z_MAX_PIN
|
|||
//
|
|||
#define SERVO0_PIN PA3 |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_STEP_PIN PE11 |
|||
#define X_DIR_PIN PE10 |
|||
#define X_ENABLE_PIN PE12 |
|||
#define X_CS_PIN PE7 |
|||
|
|||
#define Y_STEP_PIN PD8 |
|||
#define Y_DIR_PIN PB12 |
|||
#define Y_ENABLE_PIN PD9 |
|||
#define Y_CS_PIN PE15 |
|||
|
|||
#define Z_STEP_PIN PD14 |
|||
#define Z_DIR_PIN PD13 |
|||
#define Z_ENABLE_PIN PD15 |
|||
#define Z_CS_PIN PD10 |
|||
|
|||
#define E0_STEP_PIN PD5 |
|||
#define E0_DIR_PIN PD6 |
|||
#define E0_ENABLE_PIN PD4 |
|||
#define E0_CS_PIN PD7 |
|||
|
|||
#define E1_STEP_PIN PE6 |
|||
#define E1_DIR_PIN PC13 |
|||
#define E1_ENABLE_PIN PE5 |
|||
#define E1_CS_PIN PC14 |
|||
|
|||
#define E2_STEP_PIN PE2 |
|||
#define E2_DIR_PIN PE4 |
|||
#define E2_ENABLE_PIN PE3 |
|||
#define E2_CS_PIN PC15 |
|||
|
|||
#if HAS_TMC220x |
|||
/**
|
|||
* TMC2208/TMC2209 stepper drivers |
|||
* |
|||
*/ |
|||
|
|||
//
|
|||
// Software serial
|
|||
//
|
|||
#define X_SERIAL_TX_PIN PE9 |
|||
#define X_SERIAL_RX_PIN PE8 |
|||
|
|||
#define Y_SERIAL_TX_PIN PE14 |
|||
#define Y_SERIAL_RX_PIN PE13 |
|||
|
|||
#define Z_SERIAL_TX_PIN PD11 |
|||
#define Z_SERIAL_RX_PIN PD12 |
|||
|
|||
#define E0_SERIAL_TX_PIN PD3 |
|||
#define E0_SERIAL_RX_PIN PA15 |
|||
|
|||
#define E1_SERIAL_TX_PIN PC4 |
|||
#define E1_SERIAL_RX_PIN PC5 |
|||
|
|||
#define E2_SERIAL_TX_PIN PE1 |
|||
#define E2_SERIAL_RX_PIN PE0 |
|||
#endif |
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
//
|
|||
#define TEMP_0_PIN PC0 |
|||
#define TEMP_1_PIN PC1 |
|||
#define TEMP_2_PIN PC2 |
|||
#define TEMP_BED_PIN PC3 |
|||
|
|||
//
|
|||
// Heaters / Fans
|
|||
//
|
|||
#define HEATER_0_PIN PB3 |
|||
#define HEATER_1_PIN PB4 |
|||
#define HEATER_2_PIN PB15 |
|||
#define HEATER_BED_PIN PC8 |
|||
|
|||
#define FAN_PIN PB0 |
|||
#define FAN1_PIN PB1 |
|||
#define FAN2_PIN PB2 |
|||
|
|||
//
|
|||
// SPI
|
|||
//
|
|||
#define SCK_PIN PA5 |
|||
#define MISO_PIN PA6 |
|||
#define MOSI_PIN PA7 |
|||
|
|||
//
|
|||
// Misc. Functions
|
|||
//
|
|||
//#define LED_PIN PB14
|
|||
//#define BTN_PIN PC10
|
|||
//#define PS_ON_PIN PE11
|
|||
//#define KILL_PIN PC5
|
|||
|
|||
#define SDSS PA4 |
|||
|
|||
//
|
|||
// LCD / Controller
|
|||
//
|
|||
|
|||
#define BEEPER_PIN PC9 |
|||
#define SD_DETECT_PIN PB10 |
|||
|
|||
#if ENABLED(FYSETC_MINI_12864) |
|||
//
|
|||
// See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
|||
//
|
|||
#define DOGLCD_A0 PD2 |
|||
#define DOGLCD_CS PC11 |
|||
|
|||
//#define LCD_BACKLIGHT_PIN -1
|
|||
//#define KILL_PIN -1
|
|||
|
|||
#define LCD_RESET_PIN PC10 // Must be high or open for LCD to operate normally.
|
|||
// Seems to work best if left open.
|
|||
|
|||
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) |
|||
#ifndef RGB_LED_R_PIN |
|||
#define RGB_LED_R_PIN PC12 |
|||
#endif |
|||
#ifndef RGB_LED_G_PIN |
|||
#define RGB_LED_G_PIN PD0 |
|||
#endif |
|||
#ifndef RGB_LED_B_PIN |
|||
#define RGB_LED_B_PIN PD1 |
|||
#endif |
|||
#elif ENABLED(FYSETC_MINI_12864_2_1) |
|||
#define NEOPIXEL_PIN PC12 |
|||
#endif |
|||
|
|||
#elif HAS_GRAPHICAL_LCD |
|||
#define LCD_PINS_RS PD2 |
|||
#define LCD_PINS_ENABLE PC11 |
|||
#define LCD_PINS_D4 PC10 |
|||
#define LCD_PINS_D5 PC12 |
|||
#define LCD_PINS_D6 PD0 |
|||
#define LCD_PINS_D7 PD1 |
|||
|
|||
#if ENABLED(MKS_MINI_12864) |
|||
#define DOGLCD_CS PC12 |
|||
#define DOGLCD_A0 PD0 |
|||
#endif |
|||
|
|||
#endif |
|||
|
|||
#if ENABLED(NEWPANEL) |
|||
#define BTN_EN1 PC6 |
|||
#define BTN_EN2 PC7 |
|||
#define BTN_ENC PA8 |
|||
#endif |
|||
|
|||
// Alter timing for graphical display
|
|||
#if HAS_GRAPHICAL_LCD |
|||
#define BOARD_ST7920_DELAY_1 DELAY_NS(96) |
|||
#define BOARD_ST7920_DELAY_2 DELAY_NS(48) |
|||
#define BOARD_ST7920_DELAY_3 DELAY_NS(600) |
|||
#endif |
|||
|
|||
#ifndef RGB_LED_R_PIN |
|||
#define RGB_LED_R_PIN PB6 |
|||
#endif |
|||
#ifndef RGB_LED_G_PIN |
|||
#define RGB_LED_G_PIN PB5 |
|||
#endif |
|||
#ifndef RGB_LED_B_PIN |
|||
#define RGB_LED_B_PIN PB7 |
|||
#endif |
|||
#ifndef RGB_LED_W_PIN |
|||
#define RGB_LED_W_PIN -1 |
|||
#endif |
|||
|
|||
@ -0,0 +1,35 @@ |
|||
{ |
|||
"build": { |
|||
"cpu": "cortex-m4", |
|||
"extra_flags": "-DSTM32F446xx", |
|||
"f_cpu": "180000000L", |
|||
"mcu": "stm32f446ret6", |
|||
"variant": "FYSETC_S6" |
|||
}, |
|||
"connectivity": [ |
|||
"can" |
|||
], |
|||
"debug": { |
|||
"jlink_device": "STM32F446RE", |
|||
"openocd_target": "stm32f4x", |
|||
"svd_path": "STM32F446x.svd" |
|||
}, |
|||
"frameworks": [ |
|||
"arduino", |
|||
"stm32cube" |
|||
], |
|||
"name": "3D Printer control board", |
|||
"upload": { |
|||
"maximum_ram_size": 131072, |
|||
"maximum_size": 524288, |
|||
"protocol": "stlink", |
|||
"protocols": [ |
|||
"jlink", |
|||
"stlink", |
|||
"blackmagic", |
|||
"serial" |
|||
] |
|||
}, |
|||
"url": "https://www.st.com/en/microcontrollers-microprocessors/stm32f446.html", |
|||
"vendor": "FYSETC" |
|||
} |
|||
@ -0,0 +1,55 @@ |
|||
from os.path import join |
|||
Import("env", "projenv") |
|||
|
|||
import os,shutil |
|||
from SCons.Script import DefaultEnvironment |
|||
from platformio import util |
|||
|
|||
env = DefaultEnvironment() |
|||
platform = env.PioPlatform() |
|||
board = env.BoardConfig() |
|||
|
|||
FRAMEWORK_DIR = platform.get_package_dir("framework-arduinoststm32") |
|||
#FRAMEWORK_DIR = platform.get_package_dir("framework-arduinoststm32@3.10500.190327") |
|||
CMSIS_DIR = os.path.join(FRAMEWORK_DIR, "CMSIS", "CMSIS") |
|||
assert os.path.isdir(FRAMEWORK_DIR) |
|||
assert os.path.isdir(CMSIS_DIR) |
|||
assert os.path.isdir("buildroot/share/PlatformIO/variants") |
|||
|
|||
mcu_type = board.get("build.mcu")[:-2] |
|||
variant = board.get("build.variant") |
|||
series = mcu_type[:7].upper() + "xx" |
|||
variant_dir = os.path.join(FRAMEWORK_DIR, "variants", variant) |
|||
|
|||
source_dir = os.path.join("buildroot/share/PlatformIO/variants", variant) |
|||
assert os.path.isdir(source_dir) |
|||
|
|||
if not os.path.isdir(variant_dir): |
|||
os.mkdir(variant_dir) |
|||
|
|||
for file_name in os.listdir(source_dir): |
|||
full_file_name = os.path.join(source_dir, file_name) |
|||
if os.path.isfile(full_file_name): |
|||
shutil.copy(full_file_name, variant_dir) |
|||
|
|||
# Relocate firmware from 0x08000000 to 0x08002000 |
|||
#env['CPPDEFINES'].remove(("VECT_TAB_ADDR", 134217728)) |
|||
#env['CPPDEFINES'].append(("VECT_TAB_ADDR", "0x08010000")) |
|||
#env.Replace(LDSCRIPT_PATH="buildroot/share/PlatformIO/ldscripts/fysetc_aio_ii.ld") |
|||
|
|||
# Custom HEX from ELF |
|||
env.AddPostAction( |
|||
"$BUILD_DIR/${PROGNAME}.elf", |
|||
env.VerboseAction(" ".join([ |
|||
"$OBJCOPY", |
|||
"-O", |
|||
"ihex", |
|||
"$BUILD_DIR/${PROGNAME}.elf", |
|||
"$BUILD_DIR/${PROGNAME}.hex" |
|||
]), "Building $TARGET")) |
|||
|
|||
# In-line command with arguments |
|||
env.Replace( |
|||
UPLOADER=platform.get_package_dir("tool-stm32duino") + '/stm32flash/stm32flash', |
|||
UPLOADCMD='"${UPLOADER}" -v -i rts,-dtr,dtr,-rts -R -b 115200 -g 0x8000000 -w "${BUILD_DIR}/${PROGNAME}.hex" ${UPLOAD_PORT}' |
|||
) |
|||
@ -0,0 +1,361 @@ |
|||
/*
|
|||
******************************************************************************* |
|||
* Copyright (c) 2016, STMicroelectronics |
|||
* All rights reserved. |
|||
* |
|||
* Redistribution and use in source and binary forms, with or without |
|||
* modification, are permitted provided that the following conditions are met: |
|||
* |
|||
* 1. Redistributions of source code must retain the above copyright notice, |
|||
* this list of conditions and the following disclaimer. |
|||
* 2. Redistributions in binary form must reproduce the above copyright notice, |
|||
* this list of conditions and the following disclaimer in the documentation |
|||
* and/or other materials provided with the distribution. |
|||
* 3. Neither the name of STMicroelectronics nor the names of its contributors |
|||
* may be used to endorse or promote products derived from this software |
|||
* without specific prior written permission. |
|||
* |
|||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
|||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
|||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
|||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE |
|||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
|||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR |
|||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER |
|||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
|||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
|||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
|||
******************************************************************************* |
|||
*/ |
|||
#include "Arduino.h" |
|||
#include "PeripheralPins.h" |
|||
|
|||
// =====
|
|||
// Note: Commented lines are alternative possibilities which are not used per default.
|
|||
// If you change them, you will have to know what you do
|
|||
// =====
|
|||
|
|||
|
|||
//*** ADC ***
|
|||
|
|||
#ifdef HAL_ADC_MODULE_ENABLED |
|||
const PinMap PinMap_ADC[] = { |
|||
// {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
|
|||
// {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
|
|||
// {PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0
|
|||
// {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
|
|||
// {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
|
|||
// {PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1
|
|||
// {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
|
|||
// {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2
|
|||
// {PA_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2
|
|||
{PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
|
|||
// {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3
|
|||
// {PA_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3
|
|||
{PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
|
|||
// {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
|
|||
// {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
|
|||
// {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5
|
|||
// {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
|
|||
// {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6
|
|||
// {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
|
|||
// {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7
|
|||
// {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
|
|||
// {PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8
|
|||
// {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
|
|||
// {PB_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC2_IN9
|
|||
{PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
|
|||
// {PC_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC2_IN10
|
|||
// {PC_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC3_IN10
|
|||
{PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
|
|||
// {PC_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC2_IN11
|
|||
// {PC_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC3_IN11
|
|||
{PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
|
|||
// {PC_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC2_IN12
|
|||
// {PC_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC3_IN12
|
|||
{PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
|
|||
// {PC_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC2_IN13
|
|||
// {PC_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC3_IN13
|
|||
{PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
|
|||
// {PC_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC2_IN14
|
|||
// {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
|
|||
// {PC_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC2_IN15
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** DAC ***
|
|||
|
|||
#ifdef HAL_DAC_MODULE_ENABLED |
|||
const PinMap PinMap_DAC[] = { |
|||
// {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1
|
|||
// {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2 - LD2
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** I2C ***
|
|||
|
|||
#ifdef HAL_I2C_MODULE_ENABLED |
|||
const PinMap PinMap_I2C_SDA[] = { |
|||
// {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
|||
// {PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
|||
// {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
|||
{PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, |
|||
// {PC_7, FMPI2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_FMPI2C1)},
|
|||
// {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
|||
// {PC_12, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_I2C_MODULE_ENABLED |
|||
const PinMap PinMap_I2C_SCL[] = { |
|||
// {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
|||
// {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
|||
{PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, |
|||
// {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
|||
// {PC_6, FMPI2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_FMPI2C1)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** PWM ***
|
|||
|
|||
#ifdef HAL_TIM_MODULE_ENABLED |
|||
const PinMap PinMap_PWM[] = { |
|||
{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
|||
// {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
|
|||
// {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
|||
{PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
|
|||
// {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 - STLink Tx
|
|||
// {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 - STLink Tx
|
|||
// {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 - STLink Tx
|
|||
// {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 - STLink Rx
|
|||
// {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 - STLink Rx
|
|||
// {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 - STLink Rx
|
|||
{PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
|||
// {PA_5, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
|
|||
{PA_6, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1
|
|||
// {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
|||
//{PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1
|
|||
// {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
|||
// {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
|||
// {PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
|
|||
// {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
|||
{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
|||
{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
|||
{PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
|||
{PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
|||
// {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
|||
// {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
|||
{PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N
|
|||
// {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
|||
// {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
|||
{PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
|
|||
{PB_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
|
|||
{PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
|||
{PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
|||
{PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
|||
{PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
|
|||
{PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
|
|||
// {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
|
|||
// {PB_8, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
|||
{PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
|
|||
{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
|
|||
// {PB_9, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
|||
// {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
|||
{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
|
|||
{PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
|||
{PB_14, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 1, 0)}, // TIM12_CH1
|
|||
// {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
|||
// {PB_14, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N
|
|||
{PB_15, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 2, 0)}, // TIM12_CH2
|
|||
// {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
|||
// {PB_15, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
|
|||
{PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
|||
// {PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 0)}, // TIM8_CH1
|
|||
// {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
|||
{PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2
|
|||
{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
|||
// {PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 0)}, // TIM8_CH3
|
|||
// {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
|||
{PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 4, 0)}, // TIM8_CH4
|
|||
{PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
|||
{PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
|||
{PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** SERIAL ***
|
|||
|
|||
#ifdef HAL_UART_MODULE_ENABLED |
|||
const PinMap PinMap_UART_TX[] = { |
|||
// {PA_0, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
// {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
|||
{PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, |
|||
// {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
|||
// {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
|||
// {PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
|||
// {PC_10, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
{PD_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, |
|||
// {PC_12, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_UART_MODULE_ENABLED |
|||
const PinMap PinMap_UART_RX[] = { |
|||
// {PA_1, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
// {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
|||
{PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, |
|||
// {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
|||
// {PC_5, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
|||
// {PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
|||
// {PC_11, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
{PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, |
|||
// {PD_2, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_UART_MODULE_ENABLED |
|||
const PinMap PinMap_UART_RTS[] = { |
|||
// {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
|||
// {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
|||
// {PA_15, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
// {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
|||
// {PC_8, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_UART5)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_UART_MODULE_ENABLED |
|||
const PinMap PinMap_UART_CTS[] = { |
|||
// {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
|||
// {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
|||
// {PB_0, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
|||
// {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
|||
// {PC_9, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_UART5)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** SPI ***
|
|||
|
|||
#ifdef HAL_SPI_MODULE_ENABLED |
|||
const PinMap PinMap_SPI_MOSI[] = { |
|||
{PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, |
|||
// {PB_0, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI3)},
|
|||
// {PB_2, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI3)},
|
|||
// {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
|||
// {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
// {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_1, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI2)},
|
|||
// {PC_1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI3)},
|
|||
// {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_SPI_MODULE_ENABLED |
|||
const PinMap PinMap_SPI_MISO[] = { |
|||
{PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, |
|||
// {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
|||
// {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
// {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_SPI_MODULE_ENABLED |
|||
const PinMap PinMap_SPI_SCLK[] = { |
|||
{PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, |
|||
// {PA_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
|||
// {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
// {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_7, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_SPI_MODULE_ENABLED |
|||
const PinMap PinMap_SPI_SSEL[] = { |
|||
{PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, |
|||
// {PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
// {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
|||
// {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
|||
// {PB_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI2)},
|
|||
// {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
// {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** CAN ***
|
|||
|
|||
#ifdef HAL_CAN_MODULE_ENABLED |
|||
const PinMap PinMap_CAN_RD[] = { |
|||
// {PA_11, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
|||
// {PB_5, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
|||
// {PB_8, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
|||
// {PB_12, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_CAN_MODULE_ENABLED |
|||
const PinMap PinMap_CAN_TD[] = { |
|||
// {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
|||
// {PB_6, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
|||
// {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
|||
// {PB_13, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** ETHERNET ***
|
|||
|
|||
//*** No Ethernet ***
|
|||
|
|||
//*** QUADSPI ***
|
|||
|
|||
#ifdef HAL_QSPI_MODULE_ENABLED |
|||
const PinMap PinMap_QUADSPI[] = { |
|||
// {PA_1, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO3
|
|||
// {PB_2, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_CLK
|
|||
// {PB_6, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK1_NCS
|
|||
// {PC_9, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO0
|
|||
// {PC_10, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO1
|
|||
// {PC_11, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK2_NCS
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
//*** USB ***
|
|||
|
|||
#ifdef HAL_PCD_MODULE_ENABLED |
|||
const PinMap PinMap_USB_OTG_FS[] = { |
|||
// {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF
|
|||
// {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0)}, // USB_OTG_FS_VBUS
|
|||
// {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID
|
|||
{PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM
|
|||
{PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP
|
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
#ifdef HAL_PCD_MODULE_ENABLED |
|||
const PinMap PinMap_USB_OTG_HS[] = { |
|||
{NC, NP, 0} |
|||
}; |
|||
#endif |
|||
|
|||
|
|||
@ -0,0 +1,30 @@ |
|||
/* SYS_WKUP */ |
|||
#ifdef PWR_WAKEUP_PIN1 |
|||
SYS_WKUP1 = PA_0, /* SYS_WKUP0 */ |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN2 |
|||
SYS_WKUP2 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN3 |
|||
SYS_WKUP3 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN4 |
|||
SYS_WKUP4 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN5 |
|||
SYS_WKUP5 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN6 |
|||
SYS_WKUP6 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN7 |
|||
SYS_WKUP7 = NC, |
|||
#endif |
|||
#ifdef PWR_WAKEUP_PIN8 |
|||
SYS_WKUP8 = NC, |
|||
#endif |
|||
/* USB */ |
|||
#ifdef USBCON |
|||
USB_OTG_FS_DM = PA_11, |
|||
USB_OTG_FS_DP = PA_12, |
|||
#endif |
|||
@ -0,0 +1,189 @@ |
|||
/* |
|||
***************************************************************************** |
|||
** |
|||
|
|||
** File : LinkerScript.ld |
|||
** |
|||
** Abstract : Linker script for STM32F407VETx Device with |
|||
** 512KByte FLASH, 128KByte RAM |
|||
** |
|||
** Set heap size, stack size and stack location according |
|||
** to application requirements. |
|||
** |
|||
** Set memory bank area and size if external memory is used. |
|||
** |
|||
** Target : STMicroelectronics STM32 |
|||
** |
|||
** |
|||
** Distribution: The file is distributed as is, without any warranty |
|||
** of any kind. |
|||
** |
|||
***************************************************************************** |
|||
** @attention |
|||
** |
|||
** <h2><center>© COPYRIGHT(c) 2014 Ac6</center></h2> |
|||
** |
|||
** Redistribution and use in source and binary forms, with or without modification, |
|||
** are permitted provided that the following conditions are met: |
|||
** 1. Redistributions of source code must retain the above copyright notice, |
|||
** this list of conditions and the following disclaimer. |
|||
** 2. Redistributions in binary form must reproduce the above copyright notice, |
|||
** this list of conditions and the following disclaimer in the documentation |
|||
** and/or other materials provided with the distribution. |
|||
** 3. Neither the name of Ac6 nor the names of its contributors |
|||
** may be used to endorse or promote products derived from this software |
|||
** without specific prior written permission. |
|||
** |
|||
** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
|||
** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
|||
** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
|||
** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE |
|||
** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
|||
** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR |
|||
** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER |
|||
** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
|||
** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
|||
** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
|||
** |
|||
***************************************************************************** |
|||
*/ |
|||
|
|||
/* Entry Point */ |
|||
ENTRY(Reset_Handler) |
|||
|
|||
/* Highest address of the user mode stack */ |
|||
_estack = 0x20020000; /* end of RAM */ |
|||
/* Generate a link error if heap and stack don't fit into RAM */ |
|||
_Min_Heap_Size = 0x200;; /* required amount of heap */ |
|||
_Min_Stack_Size = 0x400;; /* required amount of stack */ |
|||
|
|||
/* Specify the memory areas */ |
|||
MEMORY |
|||
{ |
|||
FLASH (rx) : ORIGIN = 0x8010000, LENGTH = 512K |
|||
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K |
|||
} |
|||
|
|||
/* Define output sections */ |
|||
SECTIONS |
|||
{ |
|||
/* The startup code goes first into FLASH */ |
|||
.isr_vector : |
|||
{ |
|||
. = ALIGN(4); |
|||
KEEP(*(.isr_vector)) /* Startup code */ |
|||
. = ALIGN(4); |
|||
} >FLASH |
|||
|
|||
/* The program code and other data goes into FLASH */ |
|||
.text ALIGN(4): |
|||
{ |
|||
. = ALIGN(4); |
|||
*(.text) /* .text sections (code) */ |
|||
*(.text*) /* .text* sections (code) */ |
|||
*(.glue_7) /* glue arm to thumb code */ |
|||
*(.glue_7t) /* glue thumb to arm code */ |
|||
*(.eh_frame) |
|||
|
|||
KEEP (*(.init)) |
|||
KEEP (*(.fini)) |
|||
|
|||
. = ALIGN(4); |
|||
_etext = .; /* define a global symbols at end of code */ |
|||
} >FLASH |
|||
|
|||
/* Constant data goes into FLASH */ |
|||
.rodata ALIGN(4): |
|||
{ |
|||
. = ALIGN(4); |
|||
*(.rodata) /* .rodata sections (constants, strings, etc.) */ |
|||
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */ |
|||
. = ALIGN(4); |
|||
} >FLASH |
|||
|
|||
.ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH |
|||
.ARM : { |
|||
__exidx_start = .; |
|||
*(.ARM.exidx*) |
|||
__exidx_end = .; |
|||
} >FLASH |
|||
|
|||
.preinit_array : |
|||
{ |
|||
PROVIDE_HIDDEN (__preinit_array_start = .); |
|||
KEEP (*(.preinit_array*)) |
|||
PROVIDE_HIDDEN (__preinit_array_end = .); |
|||
} >FLASH |
|||
.init_array : |
|||
{ |
|||
PROVIDE_HIDDEN (__init_array_start = .); |
|||
KEEP (*(SORT(.init_array.*))) |
|||
KEEP (*(.init_array*)) |
|||
PROVIDE_HIDDEN (__init_array_end = .); |
|||
} >FLASH |
|||
.fini_array : |
|||
{ |
|||
PROVIDE_HIDDEN (__fini_array_start = .); |
|||
KEEP (*(SORT(.fini_array.*))) |
|||
KEEP (*(.fini_array*)) |
|||
PROVIDE_HIDDEN (__fini_array_end = .); |
|||
} >FLASH |
|||
|
|||
/* used by the startup to initialize data */ |
|||
_sidata = LOADADDR(.data); |
|||
|
|||
/* Initialized data sections goes into RAM, load LMA copy after code */ |
|||
.data : |
|||
{ |
|||
. = ALIGN(4); |
|||
_sdata = .; /* create a global symbol at data start */ |
|||
*(.data) /* .data sections */ |
|||
*(.data*) /* .data* sections */ |
|||
|
|||
. = ALIGN(4); |
|||
_edata = .; /* define a global symbol at data end */ |
|||
} >RAM AT> FLASH |
|||
|
|||
/*_siccmram = LOADADDR(.ccmram);*/ |
|||
|
|||
/* Uninitialized data section */ |
|||
. = ALIGN(4); |
|||
.bss : |
|||
{ |
|||
/* This is used by the startup in order to initialize the .bss secion */ |
|||
_sbss = .; /* define a global symbol at bss start */ |
|||
__bss_start__ = _sbss; |
|||
*(.bss) |
|||
*(.bss*) |
|||
*(COMMON) |
|||
|
|||
. = ALIGN(4); |
|||
_ebss = .; /* define a global symbol at bss end */ |
|||
__bss_end__ = _ebss; |
|||
} >RAM |
|||
|
|||
/* User_heap_stack section, used to check that there is enough RAM left */ |
|||
._user_heap_stack : |
|||
{ |
|||
. = ALIGN(4); |
|||
PROVIDE ( end = . ); |
|||
PROVIDE ( _end = . ); |
|||
. = . + _Min_Heap_Size; |
|||
. = . + _Min_Stack_Size; |
|||
. = ALIGN(4); |
|||
} >RAM |
|||
|
|||
|
|||
|
|||
/* Remove information from the standard libraries */ |
|||
/DISCARD/ : |
|||
{ |
|||
libc.a ( * ) |
|||
libm.a ( * ) |
|||
libgcc.a ( * ) |
|||
} |
|||
|
|||
.ARM.attributes 0 : { *(.ARM.attributes) } |
|||
} |
|||
|
|||
|
|||
@ -0,0 +1,201 @@ |
|||
/*
|
|||
Copyright (c) 2011 Arduino. All right reserved. |
|||
|
|||
This library is free software; you can redistribute it and/or |
|||
modify it under the terms of the GNU Lesser General Public |
|||
License as published by the Free Software Foundation; either |
|||
version 2.1 of the License, or (at your option) any later version. |
|||
|
|||
This library is distributed in the hope that it will be useful, |
|||
but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. |
|||
See the GNU Lesser General Public License for more details. |
|||
|
|||
You should have received a copy of the GNU Lesser General Public |
|||
License along with this library; if not, write to the Free Software |
|||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
|||
*/ |
|||
|
|||
#include "pins_arduino.h" |
|||
|
|||
#ifdef __cplusplus |
|||
extern "C" { |
|||
#endif |
|||
|
|||
// Pin number
|
|||
const PinName digitalPin[] = { |
|||
PA_0, //D0
|
|||
PA_1, //D1
|
|||
PA_2, //D2
|
|||
PA_3, //D3
|
|||
PA_4, //D4
|
|||
PA_5, //D5
|
|||
PA_6, //D6
|
|||
PA_7, //D7
|
|||
PA_8, //D8
|
|||
PA_9, //D9
|
|||
PA_10, //D10
|
|||
PA_11, //D11
|
|||
PA_12, //D12
|
|||
PA_13, //D13
|
|||
PA_14, //D14
|
|||
PA_15, //D15
|
|||
PB_0, //D16
|
|||
PB_1, //D17
|
|||
PB_2, //D18
|
|||
PB_3, //D19
|
|||
PB_4, //D20
|
|||
PB_5, //D21
|
|||
PB_6, //D22
|
|||
PB_7, //D23
|
|||
PB_8, //D24
|
|||
PB_9, //D25
|
|||
PB_10, //D26
|
|||
PB_11, //D27
|
|||
PB_12, //D28
|
|||
PB_13, //D29
|
|||
PB_14, //D30
|
|||
PB_15, //D31
|
|||
PC_0, //D32
|
|||
PC_1, //D33
|
|||
PC_2, //D34
|
|||
PC_3, //D35
|
|||
PC_4, //D36
|
|||
PC_5, //D37
|
|||
PC_6, //D38
|
|||
PC_7, //D39
|
|||
PC_8, //D40
|
|||
PC_9, //D41
|
|||
PC_10, //D42
|
|||
PC_11, //D43
|
|||
PC_12, //D44
|
|||
PC_13, //D45
|
|||
PC_14, //D46
|
|||
PC_15, //D47
|
|||
PD_0, //D48
|
|||
PD_1, //D49
|
|||
PD_2, //D50
|
|||
PD_3, //D51
|
|||
PD_4, //D52
|
|||
PD_5, //D53
|
|||
PD_6, //D54
|
|||
PD_7, //D55
|
|||
PD_8, //D56
|
|||
PD_9, //D57
|
|||
PD_10, //D58
|
|||
PD_11, //D59
|
|||
PD_12, //D60
|
|||
PD_13, //D61
|
|||
PD_14, //D62
|
|||
PD_15, //D63
|
|||
PE_0, //D64
|
|||
PE_1, //D65
|
|||
PE_2, //D66
|
|||
PE_3, //D67
|
|||
PE_4, //D68
|
|||
PE_5, //D69
|
|||
PE_6, //D70
|
|||
PE_7, //D71
|
|||
PE_8, //D72
|
|||
PE_9, //D73
|
|||
PE_10, //D74
|
|||
PE_11, //D75
|
|||
PE_12, //D76
|
|||
PE_13, //D77
|
|||
PE_14, //D78
|
|||
PE_15, //D79
|
|||
|
|||
//Duplicated ADC Pins
|
|||
PA_3, //D80/A0
|
|||
PA_4, //D81/A1
|
|||
PC_0, //D82/A2
|
|||
PC_1, //D83/A3
|
|||
PC_2, //D84/A4
|
|||
PC_3, //D85/A5
|
|||
PC_4 //D86/A6
|
|||
}; |
|||
|
|||
#ifdef __cplusplus |
|||
} |
|||
#endif |
|||
|
|||
// ----------------------------------------------------------------------------
|
|||
|
|||
#ifdef __cplusplus |
|||
extern "C" { |
|||
#endif |
|||
|
|||
/**
|
|||
* @brief System Clock Configuration |
|||
* The system Clock is configured as follow : |
|||
* System Clock source = PLL (HSE) |
|||
* SYSCLK(Hz) = 180000000 |
|||
* HCLK(Hz) = 180000000 |
|||
* AHB Prescaler = 1 |
|||
* APB1 Prescaler = 4 |
|||
* APB2 Prescaler = 2 |
|||
* HSE Frequency(Hz) = 12000000 |
|||
* PLL_M = 6 |
|||
* PLL_N = 180 |
|||
* PLL_P = 2 |
|||
* PLL_Q = 7 |
|||
* VDD(V) = 3.3 |
|||
* Main regulator output voltage = Scale1 mode |
|||
* Flash Latency(WS) = 5 |
|||
* @param None |
|||
* @retval None |
|||
*/ |
|||
WEAK void SystemClock_Config(void) |
|||
{ |
|||
RCC_ClkInitTypeDef RCC_ClkInitStruct; |
|||
RCC_OscInitTypeDef RCC_OscInitStruct; |
|||
RCC_PeriphCLKInitTypeDef PeriphClkInitStruct; |
|||
|
|||
|
|||
/* Enable Power Control clock */ |
|||
__HAL_RCC_PWR_CLK_ENABLE(); |
|||
|
|||
#ifdef HAL_PWR_MODULE_ENABLED |
|||
/* The voltage scaling allows optimizing the power consumption when the device is
|
|||
clocked below the maximum system frequency, to update the voltage scaling value |
|||
regarding system frequency refer to product datasheet. */ |
|||
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); |
|||
#endif |
|||
|
|||
/* Enable HSE Oscillator and activate PLL with HSE as source */ |
|||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; |
|||
RCC_OscInitStruct.HSEState = RCC_HSE_ON; |
|||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; |
|||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; |
|||
RCC_OscInitStruct.PLL.PLLM = 6; |
|||
RCC_OscInitStruct.PLL.PLLN = 180; |
|||
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; |
|||
RCC_OscInitStruct.PLL.PLLQ = 7; |
|||
RCC_OscInitStruct.PLL.PLLR = 2; |
|||
HAL_RCC_OscConfig(&RCC_OscInitStruct); |
|||
|
|||
HAL_PWREx_EnableOverDrive(); |
|||
|
|||
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
|
|||
clocks dividers */ |
|||
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | |
|||
RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); |
|||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLRCLK; |
|||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; |
|||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; |
|||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; |
|||
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5); |
|||
|
|||
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48; |
|||
PeriphClkInitStruct.PLLSAI.PLLSAIM = 6; |
|||
PeriphClkInitStruct.PLLSAI.PLLSAIN = 96; |
|||
PeriphClkInitStruct.PLLSAI.PLLSAIQ = 2; |
|||
PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV4; |
|||
PeriphClkInitStruct.PLLSAIDivQ = 1; |
|||
PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP; |
|||
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); |
|||
} |
|||
|
|||
#ifdef __cplusplus |
|||
} |
|||
#endif |
|||
@ -0,0 +1,181 @@ |
|||
/*
|
|||
Copyright (c) 2011 Arduino. All right reserved. |
|||
|
|||
This library is free software; you can redistribute it and/or |
|||
modify it under the terms of the GNU Lesser General Public |
|||
License as published by the Free Software Foundation; either |
|||
version 2.1 of the License, or (at your option) any later version. |
|||
|
|||
This library is distributed in the hope that it will be useful, |
|||
but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. |
|||
See the GNU Lesser General Public License for more details. |
|||
|
|||
You should have received a copy of the GNU Lesser General Public |
|||
License along with this library; if not, write to the Free Software |
|||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
|||
*/ |
|||
|
|||
#ifndef _VARIANT_ARDUINO_STM32_ |
|||
#define _VARIANT_ARDUINO_STM32_ |
|||
|
|||
#ifdef __cplusplus |
|||
extern "C" { |
|||
#endif // __cplusplus
|
|||
|
|||
/*----------------------------------------------------------------------------
|
|||
* Pins |
|||
*----------------------------------------------------------------------------*/ |
|||
|
|||
#define PA0 0 //D0
|
|||
#define PA1 1 //D1
|
|||
#define PA2 2 //D2
|
|||
#define PA3 3 //D3
|
|||
#define PA4 4 //D4
|
|||
#define PA5 5 //D5
|
|||
#define PA6 6 //D6
|
|||
#define PA7 7 //D7
|
|||
#define PA8 8 //D8
|
|||
#define PA9 9 //D9
|
|||
#define PA10 10 //D10
|
|||
#define PA11 11 //D11
|
|||
#define PA12 12 //D12
|
|||
#define PA13 13 //D13
|
|||
#define PA14 14 //D14
|
|||
#define PA15 15 //D15
|
|||
#define PB0 16 //D16
|
|||
#define PB1 17 //D17
|
|||
#define PB2 18 //D18
|
|||
#define PB3 19 //D19
|
|||
#define PB4 20 //D20
|
|||
#define PB5 21 //D21
|
|||
#define PB6 22 //D22
|
|||
#define PB7 23 //D23
|
|||
#define PB8 24 //D24
|
|||
#define PB9 25 //D25
|
|||
#define PB10 26 //D26
|
|||
#define PB11 27 //D27
|
|||
#define PB12 28 //D28
|
|||
#define PB13 29 //D29
|
|||
#define PB14 30 //D30
|
|||
#define PB15 31 //D31
|
|||
#define PC0 32 //D32
|
|||
#define PC1 33 //D33
|
|||
#define PC2 34 //D34
|
|||
#define PC3 35 //D35
|
|||
#define PC4 36 //D36
|
|||
#define PC5 37 //D37
|
|||
#define PC6 38 //D38
|
|||
#define PC7 39 //D39
|
|||
#define PC8 40 //D40
|
|||
#define PC9 41 //D41
|
|||
#define PC10 42 //D42
|
|||
#define PC11 43 //D43
|
|||
#define PC12 44 //D44
|
|||
#define PC13 45 //D45
|
|||
#define PC14 46 //D46
|
|||
#define PC15 47 //D47
|
|||
#define PD0 48 //D48
|
|||
#define PD1 49 //D49
|
|||
#define PD2 50 //D50
|
|||
#define PD3 51 //D51
|
|||
#define PD4 52 //D52
|
|||
#define PD5 53 //D53
|
|||
#define PD6 54 //D54
|
|||
#define PD7 55 //D55
|
|||
#define PD8 56 //D56
|
|||
#define PD9 57 //D57
|
|||
#define PD10 58 //D58
|
|||
#define PD11 59 //D59
|
|||
#define PD12 60 //D60
|
|||
#define PD13 61 //D61
|
|||
#define PD14 62 //D62
|
|||
#define PD15 63 //D63
|
|||
#define PE0 64 //D64
|
|||
#define PE1 65 //D65
|
|||
#define PE2 66 //D66
|
|||
#define PE3 67 //D67
|
|||
#define PE4 68 //D68
|
|||
#define PE5 69 //D69
|
|||
#define PE6 70 //D70
|
|||
#define PE7 71 //D71
|
|||
#define PE8 72 //D72
|
|||
#define PE9 73 //D73
|
|||
#define PE10 74 //D74
|
|||
#define PE11 75 //D75
|
|||
#define PE12 76 //D76
|
|||
#define PE13 77 //D77
|
|||
#define PE14 78 //D78
|
|||
#define PE15 79 //D79
|
|||
|
|||
// This must be a literal with the same value as PEND
|
|||
#define NUM_DIGITAL_PINS 87 |
|||
// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
|
|||
#define NUM_ANALOG_INPUTS 7 |
|||
#define NUM_ANALOG_FIRST 80 |
|||
|
|||
// PWM resolution
|
|||
#define PWM_RESOLUTION 8 |
|||
#define PWM_FREQUENCY 20000 // >= 20 Khz => inaudible noise for fans
|
|||
#define PWM_MAX_DUTY_CYCLE 255 |
|||
|
|||
// SPI Definitions
|
|||
#define PIN_SPI_SS PA4 |
|||
#define PIN_SPI_MOSI PA7 |
|||
#define PIN_SPI_MISO PA6 |
|||
#define PIN_SPI_SCK PA5 |
|||
|
|||
// I2C Definitions
|
|||
#define PIN_WIRE_SDA PB9 |
|||
#define PIN_WIRE_SCL PB8 |
|||
|
|||
// Timer Definitions
|
|||
// Do not use timer used by PWM pin. See PinMap_PWM.
|
|||
#define TIMER_TONE TIM6 |
|||
#define TIMER_SERVO TIM14 |
|||
#define TIMER_SERIAL TIM7 |
|||
|
|||
// UART Definitions
|
|||
//#define SERIAL_UART_INSTANCE 1 // Connected to EXP3 header
|
|||
/* Enable Serial 3 */ |
|||
#define HAVE_HWSERIAL1 |
|||
#define HAVE_HWSERIAL3 |
|||
|
|||
// Default pin used for 'Serial' instance (ex: ST-Link)
|
|||
// Mandatory for Firmata
|
|||
#define PIN_SERIAL_RX PA10 |
|||
#define PIN_SERIAL_TX PA9 |
|||
|
|||
/* HAL configuration */ |
|||
#define HSE_VALUE 12000000U |
|||
|
|||
#define FLASH_PAGE_SIZE ((uint32_t)(4*1024)) |
|||
|
|||
#ifdef __cplusplus |
|||
} // extern "C"
|
|||
#endif |
|||
/*----------------------------------------------------------------------------
|
|||
* Arduino objects - C++ only |
|||
*----------------------------------------------------------------------------*/ |
|||
|
|||
#ifdef __cplusplus |
|||
// These serial port names are intended to allow libraries and architecture-neutral
|
|||
// sketches to automatically default to the correct port name for a particular type
|
|||
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
|
|||
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
|
|||
//
|
|||
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
|
|||
//
|
|||
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
|
|||
//
|
|||
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
|
|||
//
|
|||
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
|
|||
//
|
|||
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
|
|||
// pins are NOT connected to anything by default.
|
|||
#define SERIAL_PORT_MONITOR Serial |
|||
#define SERIAL_PORT_HARDWARE_OPEN Serial |
|||
#endif |
|||
|
|||
#endif /* _VARIANT_ARDUINO_STM32_ */ |
|||
File diff suppressed because it is too large
File diff suppressed because it is too large
Loading…
Reference in new issue