andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Update the Ender-4 example config (#12131) 

- Enable filament change menu
- Enable bed-PID
- Enable s-curve acceleration
- Enable some menu items
- Update from Skorpi's new version
- Fix extruder steps, deactivate nozzle clean feature
pull/1/head
Hannes Brandstätter-Müller 6 years ago
committed by Scott Lahteine
parent
9c71bff5e8
commit
c36773bffb
3 changed files with 38 additions and 31 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Unified View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 38
      Marlin/src/config/examples/Creality/Ender-4/Configuration.h
  2. 24
      Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
  3. 7
      Marlin/src/inc/SanityCheck.h

38
Marlin/src/config/examples/Creality/Ender-4/Configuration.h
View File

@ -399,7 +399,7 @@
#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
#define PID_K1 0.95 // Smoothing factor within any PID loop #define PID_K1 0.95 // Smoothing factor within any PID loop
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
//#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
//#define PID_DEBUG // Sends debug data to the serial port. //#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
@ -411,9 +411,9 @@
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Ender-4 // Ender-4
#define DEFAULT_Kp 22.57 #define DEFAULT_Kp 16.67
#define DEFAULT_Ki 1.72 #define DEFAULT_Ki 1.12
#define DEFAULT_Kd 73.96 #define DEFAULT_Kd 62.14
// Ultimaker // Ultimaker
// #define DEFAULT_Kp 22.2 // #define DEFAULT_Kp 22.2
@ -449,7 +449,7 @@
* heater. If your configuration is significantly different than this and you don't understand * heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use bed PID until someone else verifies that your hardware works. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
*/ */
//#define PIDTEMPBED #define PIDTEMPBED
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
@ -502,7 +502,7 @@
* Note: For Bowden Extruders make this large enough to allow load/unload. * Note: For Bowden Extruders make this large enough to allow load/unload.
*/ */
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH 500 #define EXTRUDE_MAXLENGTH 750
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -582,7 +582,7 @@
#endif #endif
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
#define X_MIN_ENDSTOP_INVERTING true//false // set to true to invert the logic of the endstop. #define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
@ -661,14 +661,14 @@
* Override with M92 * Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/ */
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 110 } #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 100 }
/** /**
* Default Max Feed Rate (mm/s) * Default Max Feed Rate (mm/s)
* Override with M203 * Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/ */
#define DEFAULT_MAX_FEEDRATE { 300, 300, 10, 25 } #define DEFAULT_MAX_FEEDRATE { 500, 500, 15, 25 }
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
@ -676,7 +676,7 @@
* Override with M201 * Override with M201
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
*/ */
#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
@ -711,7 +711,7 @@
* *
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
*/ */
//#define S_CURVE_ACCELERATION #define S_CURVE_ACCELERATION
//=========================================================================== //===========================================================================
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
@ -978,7 +978,7 @@
#endif #endif
#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS) #if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD #define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
#endif #endif
/** /**
@ -1050,15 +1050,15 @@
*/ */
//#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR //#define AUTO_BED_LEVELING_LINEAR
#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL //#define AUTO_BED_LEVELING_UBL
//#define MESH_BED_LEVELING #define MESH_BED_LEVELING
/** /**
* Normally G28 leaves leveling disabled on completion. Enable * Normally G28 leaves leveling disabled on completion. Enable
* this option to have G28 restore the prior leveling state. * this option to have G28 restore the prior leveling state.
*/ */
//#define RESTORE_LEVELING_AFTER_G28 #define RESTORE_LEVELING_AFTER_G28
/** /**
* Enable detailed logging of G28, G29, M48, etc. * Enable detailed logging of G28, G29, M48, etc.
@ -1153,7 +1153,7 @@
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS #define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
#endif // BED_LEVELING #endif // BED_LEVELING
@ -1225,7 +1225,7 @@
// Homing speeds (mm/m) // Homing speeds (mm/m)
#define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_XY (50*60)
#define HOMING_FEEDRATE_Z (4*60) #define HOMING_FEEDRATE_Z (7*60)
// Validate that endstops are triggered on homing moves // Validate that endstops are triggered on homing moves
#define VALIDATE_HOMING_ENDSTOPS #define VALIDATE_HOMING_ENDSTOPS
@ -1352,7 +1352,7 @@
* P1 Raise the nozzle always to Z-park height. * P1 Raise the nozzle always to Z-park height.
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
*/ */
//#define NOZZLE_PARK_FEATURE #define NOZZLE_PARK_FEATURE
#if ENABLED(NOZZLE_PARK_FEATURE) #if ENABLED(NOZZLE_PARK_FEATURE)
// Specify a park position as { X, Y, Z } // Specify a park position as { X, Y, Z }
@ -1399,7 +1399,7 @@
* Attention: EXPERIMENTAL. G-code arguments may change. * Attention: EXPERIMENTAL. G-code arguments may change.
* *
*/ */
#define NOZZLE_CLEAN_FEATURE //#define NOZZLE_CLEAN_FEATURE
#if ENABLED(NOZZLE_CLEAN_FEATURE) #if ENABLED(NOZZLE_CLEAN_FEATURE)
// Default number of pattern repetitions // Default number of pattern repetitions

24
Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
View File

@ -90,7 +90,7 @@
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
* below 2. * below 2.
*/ */
#define WATCH_TEMP_PERIOD 20 // Seconds #define WATCH_TEMP_PERIOD 30 // Seconds
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
@ -263,7 +263,7 @@
*/ */
#define CASE_LIGHT_ENABLE #define CASE_LIGHT_ENABLE
#if ENABLED(CASE_LIGHT_ENABLE) #if ENABLED(CASE_LIGHT_ENABLE)
#define CASE_LIGHT_PIN ENDER4_FAN_PIN // Override the default pin if needed #define CASE_LIGHT_PIN ENDER4_FAN_PIN // Override the default pin if needed
#define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
#define CASE_LIGHT_DEFAULT_ON false // Set default power-up state on #define CASE_LIGHT_DEFAULT_ON false // Set default power-up state on
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
@ -1070,28 +1070,28 @@
* Requires NOZZLE_PARK_FEATURE. * Requires NOZZLE_PARK_FEATURE.
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
*/ */
//#define ADVANCED_PAUSE_FEATURE #define ADVANCED_PAUSE_FEATURE
#if ENABLED(ADVANCED_PAUSE_FEATURE) #if ENABLED(ADVANCED_PAUSE_FEATURE)
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
// This short retract is done immediately, before parking the nozzle. // This short retract is done immediately, before parking the nozzle.
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 35 // (mm/s) Unload filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. #define FILAMENT_CHANGE_UNLOAD_LENGTH 650 // (mm) The length of filament for a complete unload.
// For Bowden, the full length of the tube and nozzle. // For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle. // For direct drive, the full length of the nozzle.
// Set to 0 for manual unloading. // Set to 0 for manual unloading.
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
// 0 to disable start loading and skip to fast load only // 0 to disable start loading and skip to fast load only
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 35 // (mm/s) Load filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 600 // (mm) Load length of filament, from extruder gear to nozzle.
// For Bowden, the full length of the tube and nozzle. // For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle. // For direct drive, the full length of the nozzle.
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. #define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. #define ADVANCED_PAUSE_PURGE_LENGTH 60 // (mm) Length to extrude after loading.
// Set to 0 for manual extrusion. // Set to 0 for manual extrusion.
// Filament can be extruded repeatedly from the Filament Change menu // Filament can be extruded repeatedly from the Filament Change menu
// until extrusion is consistent, and to purge old filament. // until extrusion is consistent, and to purge old filament.
@ -1105,10 +1105,10 @@
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change #define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#endif #endif

7
Marlin/src/inc/SanityCheck.h
View File

@ -1234,6 +1234,13 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
#endif #endif
#endif #endif
/**
* Test case light not using the same pin as the fan
*/
#if ENABLED(CASE_LIGHT_ENABLE) && CASE_LIGHT_PIN == FAN_PIN
#error "You cannot set CASE_LIGHT_PIN equal to FAN_PIN."
#endif
/** /**
* Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set. * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set.
*/ */

Write Preview
Loading…
Cancel
Save