diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h index 79be3236d7..fe2ad9e24e 100644 --- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h +++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h @@ -399,7 +399,7 @@ #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) - //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. + #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay @@ -411,9 +411,9 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ender-4 - #define DEFAULT_Kp 22.57 - #define DEFAULT_Ki 1.72 - #define DEFAULT_Kd 73.96 + #define DEFAULT_Kp 16.67 + #define DEFAULT_Ki 1.12 + #define DEFAULT_Kd 62.14 // Ultimaker // #define DEFAULT_Kp 22.2 @@ -449,7 +449,7 @@ * heater. If your configuration is significantly different than this and you don't understand * the issues involved, don't use bed PID until someone else verifies that your hardware works. */ -//#define PIDTEMPBED +#define PIDTEMPBED //#define BED_LIMIT_SWITCHING @@ -502,7 +502,7 @@ * Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH 500 +#define EXTRUDE_MAXLENGTH 750 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -582,7 +582,7 @@ #endif // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). -#define X_MIN_ENDSTOP_INVERTING true//false // set to true to invert the logic of the endstop. +#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. @@ -661,14 +661,14 @@ * Override with M92 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 110 } +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 100 } /** * Default Max Feed Rate (mm/s) * Override with M203 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_FEEDRATE { 300, 300, 10, 25 } +#define DEFAULT_MAX_FEEDRATE { 500, 500, 15, 25 } /** * Default Max Acceleration (change/s) change = mm/s @@ -676,7 +676,7 @@ * Override with M201 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } /** * Default Acceleration (change/s) change = mm/s @@ -711,7 +711,7 @@ * * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained */ -//#define S_CURVE_ACCELERATION +#define S_CURVE_ACCELERATION //=========================================================================== //============================= Z Probe Options ============================= @@ -978,7 +978,7 @@ #endif #if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS) - //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD + #define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD #endif /** @@ -1050,15 +1050,15 @@ */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR -#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL -//#define MESH_BED_LEVELING +#define MESH_BED_LEVELING /** * Normally G28 leaves leveling disabled on completion. Enable * this option to have G28 restore the prior leveling state. */ -//#define RESTORE_LEVELING_AFTER_G28 +#define RESTORE_LEVELING_AFTER_G28 /** * Enable detailed logging of G28, G29, M48, etc. @@ -1153,7 +1153,7 @@ #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X - //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + #define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS #endif // BED_LEVELING @@ -1225,7 +1225,7 @@ // Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (50*60) -#define HOMING_FEEDRATE_Z (4*60) +#define HOMING_FEEDRATE_Z (7*60) // Validate that endstops are triggered on homing moves #define VALIDATE_HOMING_ENDSTOPS @@ -1352,7 +1352,7 @@ * P1 Raise the nozzle always to Z-park height. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. */ -//#define NOZZLE_PARK_FEATURE +#define NOZZLE_PARK_FEATURE #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z } @@ -1399,7 +1399,7 @@ * Attention: EXPERIMENTAL. G-code arguments may change. * */ -#define NOZZLE_CLEAN_FEATURE +//#define NOZZLE_CLEAN_FEATURE #if ENABLED(NOZZLE_CLEAN_FEATURE) // Default number of pattern repetitions diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h index af4e46ecfd..c64dadd389 100644 --- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h @@ -90,7 +90,7 @@ * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set * below 2. */ - #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_PERIOD 30 // Seconds #define WATCH_TEMP_INCREASE 2 // Degrees Celsius #endif @@ -263,7 +263,7 @@ */ #define CASE_LIGHT_ENABLE #if ENABLED(CASE_LIGHT_ENABLE) - #define CASE_LIGHT_PIN ENDER4_FAN_PIN // Override the default pin if needed + #define CASE_LIGHT_PIN ENDER4_FAN_PIN // Override the default pin if needed #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW #define CASE_LIGHT_DEFAULT_ON false // Set default power-up state on #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) @@ -1070,28 +1070,28 @@ * Requires NOZZLE_PARK_FEATURE. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. // This short retract is done immediately, before parking the nozzle. - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 35 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 650 // (mm) The length of filament for a complete unload. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. // Set to 0 for manual unloading. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. // 0 to disable start loading and skip to fast load only - #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 35 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 600 // (mm) Load length of filament, from extruder gear to nozzle. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. - //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. - #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + #define ADVANCED_PAUSE_PURGE_LENGTH 60 // (mm) Length to extrude after loading. // Set to 0 for manual extrusion. // Filament can be extruded repeatedly from the Filament Change menu // until extrusion is consistent, and to purge old filament. @@ -1105,10 +1105,10 @@ #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. - //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. - //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + #define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #endif diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 0647c180cc..e2ccb3963a 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -1234,6 +1234,13 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE, #endif #endif +/** + * Test case light not using the same pin as the fan + */ +#if ENABLED(CASE_LIGHT_ENABLE) && CASE_LIGHT_PIN == FAN_PIN + #error "You cannot set CASE_LIGHT_PIN equal to FAN_PIN." +#endif + /** * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set. */