Update the Ender-4 example config (#12131)

- Enable filament change menu - Enable bed-PID - Enable s-curve acceleration - Enable some menu items - Update from Skorpi's new version - Fix extruder steps, deactivate nozzle clean feature
6 years ago · c36773bffb
3 changed files with 38 additions and 31 deletions
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@ -399,7 +399,7 @@
 #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
-  //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+  #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  //#define PID_DEBUG // Sends debug data to the serial port.
  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
@ -411,9 +411,9 @@
  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it

  // Ender-4
-  #define DEFAULT_Kp 22.57
-  #define DEFAULT_Ki 1.72
-  #define DEFAULT_Kd 73.96
+  #define DEFAULT_Kp 16.67
+  #define DEFAULT_Ki 1.12
+  #define DEFAULT_Kd 62.14

  // Ultimaker
 //  #define DEFAULT_Kp 22.2
@ -449,7 +449,7 @@
 * heater. If your configuration is significantly different than this and you don't understand
 * the issues involved, don't use bed PID until someone else verifies that your hardware works.
 */
-//#define PIDTEMPBED
+#define PIDTEMPBED

 //#define BED_LIMIT_SWITCHING

@ -502,7 +502,7 @@
 * Note: For Bowden Extruders make this large enough to allow load/unload.
 */
 #define PREVENT_LENGTHY_EXTRUDE
-#define EXTRUDE_MAXLENGTH 500
+#define EXTRUDE_MAXLENGTH 750

 //===========================================================================
 //======================== Thermal Runaway Protection =======================
@ -582,7 +582,7 @@
 #endif

 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true//false // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
@ -661,14 +661,14 @@
 * Override with M92
 *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
 */
-#define DEFAULT_AXIS_STEPS_PER_UNIT    { 80, 80, 400, 110 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT    { 80, 80, 400, 100 }

 /**
 * Default Max Feed Rate (mm/s)
 * Override with M203
 *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
 */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 10, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 500, 500, 15, 25 }

 /**
 * Default Max Acceleration (change/s) change = mm/s
@ -676,7 +676,7 @@
 * Override with M201
 *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
 */
-#define DEFAULT_MAX_ACCELERATION      { 500, 500, 100, 5000 }
+#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }

 /**
 * Default Acceleration (change/s) change = mm/s
@ -711,7 +711,7 @@
 *
 * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
 */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION

 //===========================================================================
 //============================= Z Probe Options =============================
@ -978,7 +978,7 @@
 #endif

 #if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM    // Enable/Disable software endstops from the LCD
 #endif

 /**
@ -1050,15 +1050,15 @@
 */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-#define AUTO_BED_LEVELING_BILINEAR
+//#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-//#define MESH_BED_LEVELING
+#define MESH_BED_LEVELING

 /**
 * Normally G28 leaves leveling disabled on completion. Enable
 * this option to have G28 restore the prior leveling state.
 */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28

 /**
 * Enable detailed logging of G28, G29, M48, etc.
@ -1153,7 +1153,7 @@
  #define GRID_MAX_POINTS_X 3    // Don't use more than 7 points per axis, implementation limited.
  #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

-  //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
+  #define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS

 #endif // BED_LEVELING

@ -1225,7 +1225,7 @@

 // Homing speeds (mm/m)
 #define HOMING_FEEDRATE_XY (50*60)
-#define HOMING_FEEDRATE_Z  (4*60)
+#define HOMING_FEEDRATE_Z  (7*60)

 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@ -1352,7 +1352,7 @@
 *    P1  Raise the nozzle always to Z-park height.
 *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
 */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE

 #if ENABLED(NOZZLE_PARK_FEATURE)
  // Specify a park position as { X, Y, Z }
@ -1399,7 +1399,7 @@
 * Attention: EXPERIMENTAL. G-code arguments may change.
 *
 */
-#define NOZZLE_CLEAN_FEATURE
+//#define NOZZLE_CLEAN_FEATURE

 #if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@ -90,7 +90,7 @@
   * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
   * below 2.
   */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_PERIOD 30                // Seconds
  #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif

@ -263,7 +263,7 @@
 */
 #define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
-  #define CASE_LIGHT_PIN ENDER4_FAN_PIN      // Override the default pin if needed
+  #define CASE_LIGHT_PIN ENDER4_FAN_PIN       // Override the default pin if needed
  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
  #define CASE_LIGHT_DEFAULT_ON false         // Set default power-up state on
  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
@ -1070,28 +1070,28 @@
 * Requires NOZZLE_PARK_FEATURE.
 * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
 */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
  #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
                                                  // This short retract is done immediately, before parking the nozzle.
-  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     35  // (mm/s) Unload filament feedrate. This can be pretty fast.
  #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      650  // (mm) The length of filament for a complete unload.
                                                  //   For Bowden, the full length of the tube and nozzle.
                                                  //   For direct drive, the full length of the nozzle.
                                                  //   Set to 0 for manual unloading.
  #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
  #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
                                                  // 0 to disable start loading and skip to fast load only
-  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  35  // (mm/s) Load filament feedrate. This can be pretty fast.
  #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   600  // (mm) Load length of filament, from extruder gear to nozzle.
                                                  //   For Bowden, the full length of the tube and nozzle.
                                                  //   For direct drive, the full length of the nozzle.
-  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
+  #define ADVANCED_PAUSE_CONTINUOUS_PURGE         // Purge continuously up to the purge length until interrupted.
  #define ADVANCED_PAUSE_PURGE_FEEDRATE        3  // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
-  #define ADVANCED_PAUSE_PURGE_LENGTH         50  // (mm) Length to extrude after loading.
+  #define ADVANCED_PAUSE_PURGE_LENGTH         60  // (mm) Length to extrude after loading.
                                                  //   Set to 0 for manual extrusion.
                                                  //   Filament can be extruded repeatedly from the Filament Change menu
                                                  //   until extrusion is consistent, and to purge old filament.
@ -1105,10 +1105,10 @@
  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
  #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.

-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
+  #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE             // Ensure homing has been completed prior to parking for filament change

-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif

--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@ -1234,6 +1234,13 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
  #endif
 #endif

+/**
+ * Test case light not using the same pin as the fan
+ */
+#if ENABLED(CASE_LIGHT_ENABLE) && CASE_LIGHT_PIN == FAN_PIN
+  #error "You cannot set CASE_LIGHT_PIN equal to FAN_PIN."
+#endif
+
 /**
 * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set.
 */