Browse Source

Raise STM32F1 UART IRQ Priority, add error handling (#19301)

(Error handling for Overrun, Framing and Parity.)
vanilla_fb_2.0.x
Victor Oliveira 4 years ago
committed by GitHub
parent
commit
b98946b5c1
No known key found for this signature in database GPG Key ID: 4AEE18F83AFDEB23
  1. 6
      Marlin/src/HAL/STM32/MarlinSerial.cpp
  2. 19
      Marlin/src/HAL/STM32F1/MarlinSerial.cpp
  3. 15
      Marlin/src/HAL/STM32F1/MarlinSerial.h

6
Marlin/src/HAL/STM32/MarlinSerial.cpp

@ -55,10 +55,8 @@
void MarlinSerial::begin(unsigned long baud, uint8_t config) {
HardwareSerial::begin(baud, config);
// replace the IRQ callback with the one we have defined
#if ENABLED(EMERGENCY_PARSER)
_serial.rx_callback = _rx_callback;
#endif
// Replace the IRQ callback with the one we have defined
TERN_(EMERGENCY_PARSER, _serial.rx_callback = _rx_callback);
}
// This function is Copyright (c) 2006 Nicholas Zambetti.

19
Marlin/src/HAL/STM32F1/MarlinSerial.cpp

@ -35,7 +35,14 @@ static inline __always_inline void my_usart_irq(ring_buffer *rb, ring_buffer *wb
* See table 198 (sec 27.4, p809) in STM document RM0008 rev 15.
* We enable RXNEIE.
*/
if ((regs->CR1 & USART_CR1_RXNEIE) && (regs->SR & USART_SR_RXNE)) {
uint32_t srflags = regs->SR, cr1its = regs->CR1;
if ((cr1its & USART_CR1_RXNEIE) && (srflags & USART_SR_RXNE)) {
if (srflags & USART_SR_FE || srflags & USART_SR_PE ) {
// framing error or parity error
regs->DR; // Read and throw away the data, which also clears FE and PE
}
else {
uint8_t c = (uint8)regs->DR;
#ifdef USART_SAFE_INSERT
// If the buffer is full and the user defines USART_SAFE_INSERT,
@ -49,8 +56,16 @@ static inline __always_inline void my_usart_irq(ring_buffer *rb, ring_buffer *wb
emergency_parser.update(serial.emergency_state, c);
#endif
}
}
else if (srflags & USART_SR_ORE) {
// overrun and empty data, just do a dummy read to clear ORE
// and prevent a raise condition where a continous interrupt stream (due to ORE set) occurs
// (see chapter "Overrun error" ) in STM32 reference manual
regs->DR;
}
// TXE signifies readiness to send a byte to DR.
if ((regs->CR1 & USART_CR1_TXEIE) && (regs->SR & USART_SR_TXE)) {
if ((cr1its & USART_CR1_TXEIE) && (srflags & USART_SR_TXE)) {
if (!rb_is_empty(wb))
regs->DR=rb_remove(wb);
else

15
Marlin/src/HAL/STM32F1/MarlinSerial.h

@ -22,6 +22,7 @@
#pragma once
#include <HardwareSerial.h>
#include <libmaple/usart.h>
#include <WString.h>
#include "../../inc/MarlinConfigPre.h"
@ -29,6 +30,8 @@
#include "../../feature/e_parser.h"
#endif
#define UART_IRQ_PRIO 1
class MarlinSerial : public HardwareSerial {
public:
MarlinSerial(struct usart_dev *usart_device, uint8 tx_pin, uint8 rx_pin) :
@ -38,6 +41,18 @@ public:
#endif
{ }
#ifdef UART_IRQ_PRIO
// shadow the parent methods to set irq priority after the begin
void begin(uint32 baud) {
MarlinSerial::begin(baud, SERIAL_8N1);
}
void begin(uint32 baud, uint8_t config) {
HardwareSerial::begin(baud, config);
nvic_irq_set_priority(c_dev()->irq_num, UART_IRQ_PRIO);
}
#endif
#if ENABLED(EMERGENCY_PARSER)
EmergencyParser::State emergency_state;
#endif

Loading…
Cancel
Save