andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Show M503 report with current linear units

pull/1/head
Scott Lahteine 8 years ago
committed by Scott Lahteine
parent
871f92378c
commit
b956f2642b
1 changed files with 165 additions and 148 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 313
      Marlin/configuration_store.cpp

313
Marlin/configuration_store.cpp
View File

@ -1165,6 +1165,13 @@ void MarlinSettings::reset() {
#define CONFIG_ECHO_START do{ if (!forReplay) SERIAL_ECHO_START; }while(0)
#if ENABLED(INCH_MODE_SUPPORT)
extern float linear_unit_factor;
#define LINEAR_UNIT(N) ((N) / linear_unit_factor)
#else
#define LINEAR_UNIT(N) N
#endif
/**
* M503 - Report current settings in RAM
*
@ -1172,113 +1179,168 @@ void MarlinSettings::reset() {
*/
void MarlinSettings::report(bool forReplay) {
/**
* Announce current units, in case inches are being displayed
*/
CONFIG_ECHO_START;
#if ENABLED(INCH_MODE_SUPPORT)
extern float linear_unit_factor, volumetric_unit_factor;
#define LINEAR_UNIT(N) ((N) / linear_unit_factor)
#define VOLUMETRIC_UNIT(N) ((N) / (volumetric_enabled ? volumetric_unit_factor : linear_unit_factor))
serialprintPGM(linear_unit_factor == 1.0 ? PSTR(" G21 ; Units in mm\n") : PSTR(" G20 ; Units in inches\n"));
#else
#define LINEAR_UNIT(N) N
#define VOLUMETRIC_UNIT(N) N
SERIAL_ECHOLNPGM(" G21 ; Units in mm\n");
#endif
SERIAL_EOL;
/**
* Volumetric extrusion M200
*/
if (!forReplay) {
SERIAL_ECHOLNPGM("Steps per unit:");
CONFIG_ECHO_START;
SERIAL_ECHOPGM("Filament settings:");
if (volumetric_enabled)
SERIAL_EOL;
else
SERIAL_ECHOLNPGM(" Disabled");
}
SERIAL_ECHOPAIR(" M92 X", planner.axis_steps_per_mm[X_AXIS]);
SERIAL_ECHOPAIR(" Y", planner.axis_steps_per_mm[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", planner.axis_steps_per_mm[Z_AXIS]);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 D", filament_size[0]);
SERIAL_EOL;
#if EXTRUDERS > 1
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]);
SERIAL_EOL;
#if EXTRUDERS > 2
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]);
SERIAL_EOL;
#if EXTRUDERS > 3
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T3 D", filament_size[3]);
SERIAL_EOL;
#if EXTRUDERS > 4
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T4 D", filament_size[4]);
SERIAL_EOL;
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
#endif // EXTRUDERS > 1
if (!volumetric_enabled) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM(" M200 D0");
}
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Steps per unit:");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M92 X", LINEAR_UNIT(planner.axis_steps_per_mm[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(planner.axis_steps_per_mm[Y_AXIS]));
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.axis_steps_per_mm[Z_AXIS]));
#if DISABLED(DISTINCT_E_FACTORS)
SERIAL_ECHOPAIR(" E", planner.axis_steps_per_mm[E_AXIS]);
SERIAL_ECHOPAIR(" E", VOLUMETRIC_UNIT(planner.axis_steps_per_mm[E_AXIS]));
#endif
SERIAL_EOL;
#if ENABLED(DISTINCT_E_FACTORS)
CONFIG_ECHO_START;
for (uint8_t i = 0; i < E_STEPPERS; i++) {
SERIAL_ECHOPAIR(" M92 T", (int)i);
SERIAL_ECHOLNPAIR(" E", planner.axis_steps_per_mm[E_AXIS + i]);
SERIAL_ECHOLNPAIR(" E", VOLUMETRIC_UNIT(planner.axis_steps_per_mm[E_AXIS + i]));
}
#endif
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Maximum feedrates (mm/s):");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Maximum feedrates (units/s):");
}
SERIAL_ECHOPAIR(" M203 X", planner.max_feedrate_mm_s[X_AXIS]);
SERIAL_ECHOPAIR(" Y", planner.max_feedrate_mm_s[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", planner.max_feedrate_mm_s[Z_AXIS]);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M203 X", LINEAR_UNIT(planner.max_feedrate_mm_s[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(planner.max_feedrate_mm_s[Y_AXIS]));
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.max_feedrate_mm_s[Z_AXIS]));
#if DISABLED(DISTINCT_E_FACTORS)
SERIAL_ECHOPAIR(" E", planner.max_feedrate_mm_s[E_AXIS]);
SERIAL_ECHOPAIR(" E", VOLUMETRIC_UNIT(planner.max_feedrate_mm_s[E_AXIS]));
#endif
SERIAL_EOL;
#if ENABLED(DISTINCT_E_FACTORS)
CONFIG_ECHO_START;
for (uint8_t i = 0; i < E_STEPPERS; i++) {
SERIAL_ECHOPAIR(" M203 T", (int)i);
SERIAL_ECHOLNPAIR(" E", planner.max_feedrate_mm_s[E_AXIS + i]);
SERIAL_ECHOLNPAIR(" E", VOLUMETRIC_UNIT(planner.max_feedrate_mm_s[E_AXIS + i]));
}
#endif
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Maximum Acceleration (mm/s2):");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Maximum Acceleration (units/s2):");
}
SERIAL_ECHOPAIR(" M201 X", planner.max_acceleration_mm_per_s2[X_AXIS]);
SERIAL_ECHOPAIR(" Y", planner.max_acceleration_mm_per_s2[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", planner.max_acceleration_mm_per_s2[Z_AXIS]);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M201 X", LINEAR_UNIT(planner.max_acceleration_mm_per_s2[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(planner.max_acceleration_mm_per_s2[Y_AXIS]));
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.max_acceleration_mm_per_s2[Z_AXIS]));
#if DISABLED(DISTINCT_E_FACTORS)
SERIAL_ECHOPAIR(" E", planner.max_acceleration_mm_per_s2[E_AXIS]);
SERIAL_ECHOPAIR(" E", VOLUMETRIC_UNIT(planner.max_acceleration_mm_per_s2[E_AXIS]));
#endif
SERIAL_EOL;
#if ENABLED(DISTINCT_E_FACTORS)
SERIAL_ECHO_START;
for (uint8_t i = 0; i < E_STEPPERS; i++) {
SERIAL_ECHOPAIR(" M201 T", (int)i);
SERIAL_ECHOLNPAIR(" E", planner.max_acceleration_mm_per_s2[E_AXIS + i]);
SERIAL_ECHOLNPAIR(" E", VOLUMETRIC_UNIT(planner.max_acceleration_mm_per_s2[E_AXIS + i]));
}
#endif
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Accelerations: P=printing, R=retract and T=travel");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>");
}
SERIAL_ECHOPAIR(" M204 P", planner.acceleration);
SERIAL_ECHOPAIR(" R", planner.retract_acceleration);
SERIAL_ECHOPAIR(" T", planner.travel_acceleration);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M204 P", LINEAR_UNIT(planner.acceleration));
SERIAL_ECHOPAIR(" R", LINEAR_UNIT(planner.retract_acceleration));
SERIAL_ECHOLNPAIR(" T", LINEAR_UNIT(planner.travel_acceleration));
if (!forReplay) {
SERIAL_ECHOLNPGM("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>");
}
SERIAL_ECHOPAIR(" M205 S", planner.min_feedrate_mm_s);
SERIAL_ECHOPAIR(" T", planner.min_travel_feedrate_mm_s);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M205 S", LINEAR_UNIT(planner.min_feedrate_mm_s));
SERIAL_ECHOPAIR(" T", LINEAR_UNIT(planner.min_travel_feedrate_mm_s));
SERIAL_ECHOPAIR(" B", planner.min_segment_time);
SERIAL_ECHOPAIR(" X", planner.max_jerk[X_AXIS]);
SERIAL_ECHOPAIR(" Y", planner.max_jerk[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", planner.max_jerk[Z_AXIS]);
SERIAL_ECHOPAIR(" E", planner.max_jerk[E_AXIS]);
SERIAL_EOL;
SERIAL_ECHOPAIR(" X", LINEAR_UNIT(planner.max_jerk[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(planner.max_jerk[Y_AXIS]));
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.max_jerk[Z_AXIS]));
SERIAL_ECHOLNPAIR(" E", LINEAR_UNIT(planner.max_jerk[E_AXIS]));
#if HAS_M206_COMMAND
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Home offset (mm)");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Home offset:");
}
SERIAL_ECHOPAIR(" M206 X", home_offset[X_AXIS]);
SERIAL_ECHOPAIR(" Y", home_offset[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", home_offset[Z_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M206 X", LINEAR_UNIT(home_offset[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(home_offset[Y_AXIS]));
SERIAL_ECHOLNPAIR(" Z", LINEAR_UNIT(home_offset[Z_AXIS]));
#endif
#if HOTENDS > 1
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Hotend offsets (mm)");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Hotend offsets:");
}
CONFIG_ECHO_START;
for (uint8_t e = 1; e < HOTENDS; e++) {
SERIAL_ECHOPAIR(" M218 T", (int)e);
SERIAL_ECHOPAIR(" X", hotend_offset[X_AXIS][e]);
SERIAL_ECHOPAIR(" Y", hotend_offset[Y_AXIS][e]);
SERIAL_ECHOPAIR(" X", LINEAR_UNIT(hotend_offset[X_AXIS][e]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(hotend_offset[Y_AXIS][e]));
#if ENABLED(DUAL_X_CARRIAGE) || ENABLED(SWITCHING_EXTRUDER)
SERIAL_ECHOPAIR(" Z", hotend_offset[Z_AXIS][e]);
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(hotend_offset[Z_AXIS][e]));
#endif
SERIAL_EOL;
}
@ -1287,12 +1349,13 @@ void MarlinSettings::reset() {
#if ENABLED(MESH_BED_LEVELING)
if (!forReplay) {
SERIAL_ECHOLNPGM("Mesh Bed Leveling:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Mesh Bed Leveling:");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M420 S", mbl.has_mesh() ? 1 : 0);
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
SERIAL_ECHOLNPAIR(" Z", planner.z_fade_height);
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.z_fade_height));
#endif
SERIAL_EOL;
for (uint8_t py = 0; py < GRID_MAX_POINTS_Y; py++) {
@ -1301,7 +1364,7 @@ void MarlinSettings::reset() {
SERIAL_ECHOPAIR(" G29 S3 X", (int)px + 1);
SERIAL_ECHOPAIR(" Y", (int)py + 1);
SERIAL_ECHOPGM(" Z");
SERIAL_PROTOCOL_F(mbl.z_values[px][py], 5);
SERIAL_PROTOCOL_F(LINEAR_UNIT(mbl.z_values[px][py]), 5);
SERIAL_EOL;
}
}
@ -1309,12 +1372,13 @@ void MarlinSettings::reset() {
#elif ENABLED(AUTO_BED_LEVELING_UBL)
if (!forReplay) {
SERIAL_ECHOLNPGM("Unified Bed Leveling:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Unified Bed Leveling:");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M420 S", ubl.state.active ? 1 : 0);
//#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
// SERIAL_ECHOLNPAIR(" Z", ubl.state.g29_correction_fade_height);
// SERIAL_ECHOPAIR(" Z", ubl.state.g29_correction_fade_height);
//#endif
SERIAL_EOL;
@ -1351,72 +1415,69 @@ void MarlinSettings::reset() {
#elif HAS_ABL
if (!forReplay) {
SERIAL_ECHOLNPGM("Auto Bed Leveling:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Auto Bed Leveling:");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M420 S", planner.abl_enabled ? 1 : 0);
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
SERIAL_ECHOLNPAIR(" Z", planner.z_fade_height);
SERIAL_ECHOPAIR(" Z", LINEAR_UNIT(planner.z_fade_height));
#endif
SERIAL_EOL;
#endif
#if ENABLED(DELTA)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Endstop adjustment (mm):");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Endstop adjustment:");
}
SERIAL_ECHOPAIR(" M666 X", endstop_adj[X_AXIS]);
SERIAL_ECHOPAIR(" Y", endstop_adj[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", endstop_adj[Z_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M666 X", LINEAR_UNIT(endstop_adj[X_AXIS]));
SERIAL_ECHOPAIR(" Y", LINEAR_UNIT(endstop_adj[Y_AXIS]));
SERIAL_ECHOLNPAIR(" Z", LINEAR_UNIT(endstop_adj[Z_AXIS]));
if (!forReplay) {
SERIAL_ECHOLNPGM("Delta settings: L=diagonal_rod, R=radius, H=height, S=segments_per_second, ABC=diagonal_rod_trim_tower_[123]");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Delta settings: L<diagonal_rod> R<radius> H<height> S<segments_per_s> ABC<diagonal_rod_[123]_trim>");
}
SERIAL_ECHOPAIR(" M665 L", delta_diagonal_rod);
SERIAL_ECHOPAIR(" R", delta_radius);
SERIAL_ECHOPAIR(" H", DELTA_HEIGHT + home_offset[Z_AXIS]);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M665 L", LINEAR_UNIT(delta_diagonal_rod));
SERIAL_ECHOPAIR(" R", LINEAR_UNIT(delta_radius));
SERIAL_ECHOPAIR(" H", LINEAR_UNIT(DELTA_HEIGHT + home_offset[Z_AXIS]));
SERIAL_ECHOPAIR(" S", delta_segments_per_second);
SERIAL_ECHOPAIR(" A", delta_diagonal_rod_trim[A_AXIS]);
SERIAL_ECHOPAIR(" B", delta_diagonal_rod_trim[B_AXIS]);
SERIAL_ECHOPAIR(" C", delta_diagonal_rod_trim[C_AXIS]);
SERIAL_ECHOPAIR(" I", delta_tower_angle_trim[A_AXIS]);
SERIAL_ECHOPAIR(" J", delta_tower_angle_trim[B_AXIS]);
SERIAL_ECHOPAIR(" K", delta_tower_angle_trim[C_AXIS]);
SERIAL_EOL;
SERIAL_ECHOPAIR(" A", LINEAR_UNIT(delta_diagonal_rod_trim[A_AXIS]));
SERIAL_ECHOPAIR(" B", LINEAR_UNIT(delta_diagonal_rod_trim[B_AXIS]));
SERIAL_ECHOPAIR(" C", LINEAR_UNIT(delta_diagonal_rod_trim[C_AXIS]));
SERIAL_ECHOPAIR(" I", LINEAR_UNIT(delta_tower_angle_trim[A_AXIS]));
SERIAL_ECHOPAIR(" J", LINEAR_UNIT(delta_tower_angle_trim[B_AXIS]));
SERIAL_ECHOLNPAIR(" K", LINEAR_UNIT(delta_tower_angle_trim[C_AXIS]));
#elif ENABLED(Z_DUAL_ENDSTOPS)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Z2 Endstop adjustment (mm):");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Z2 Endstop adjustment:");
}
SERIAL_ECHOPAIR(" M666 Z", z_endstop_adj);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOLNPAIR(" M666 Z", LINEAR_UNIT(z_endstop_adj));
#endif // DELTA
#if ENABLED(ULTIPANEL)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Material heatup parameters:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Material heatup parameters:");
}
CONFIG_ECHO_START;
for (uint8_t i = 0; i < COUNT(lcd_preheat_hotend_temp); i++) {
SERIAL_ECHOPAIR(" M145 S", (int)i);
SERIAL_ECHOPAIR(" H", lcd_preheat_hotend_temp[i]);
SERIAL_ECHOPAIR(" B", lcd_preheat_bed_temp[i]);
SERIAL_ECHOPAIR(" F", lcd_preheat_fan_speed[i]);
SERIAL_EOL;
SERIAL_ECHOLNPAIR(" F", lcd_preheat_fan_speed[i]);
}
#endif // ULTIPANEL
#if HAS_PID_HEATING
CONFIG_ECHO_START;
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("PID settings:");
}
#if ENABLED(PIDTEMP)
@ -1462,113 +1523,69 @@ void MarlinSettings::reset() {
#endif // PIDTEMP || PIDTEMPBED
#if HAS_LCD_CONTRAST
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("LCD Contrast:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("LCD Contrast:");
}
SERIAL_ECHOPAIR(" M250 C", lcd_contrast);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOLNPAIR(" M250 C", lcd_contrast);
#endif
#if ENABLED(FWRETRACT)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Retract: S=Length (mm) F:Speed (mm/m) Z: ZLift (mm)");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Retract: S<length> F<units/m> Z<lift>");
}
SERIAL_ECHOPAIR(" M207 S", retract_length);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M207 S", LINEAR_UNIT(retract_length));
#if EXTRUDERS > 1
SERIAL_ECHOPAIR(" W", retract_length_swap);
SERIAL_ECHOPAIR(" W", LINEAR_UNIT(retract_length_swap));
#endif
SERIAL_ECHOPAIR(" F", MMS_TO_MMM(retract_feedrate_mm_s));
SERIAL_ECHOPAIR(" Z", retract_zlift);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_feedrate_mm_s)));
SERIAL_ECHOLNPAIR(" Z", LINEAR_UNIT(retract_zlift));
if (!forReplay) {
SERIAL_ECHOLNPGM("Recover: S=Extra length (mm) F:Speed (mm/m)");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Recover: S<length> F<units/m>");
}
SERIAL_ECHOPAIR(" M208 S", retract_recover_length);
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M208 S", LINEAR_UNIT(retract_recover_length));
#if EXTRUDERS > 1
SERIAL_ECHOPAIR(" W", retract_recover_length_swap);
SERIAL_ECHOPAIR(" W", LINEAR_UNIT(retract_recover_length_swap));
#endif
SERIAL_ECHOPAIR(" F", MMS_TO_MMM(retract_recover_feedrate_mm_s));
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOLNPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_recover_feedrate_mm_s)));
if (!forReplay) {
SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries");
}
SERIAL_ECHOPAIR(" M209 S", autoretract_enabled ? 1 : 0);
SERIAL_EOL;
#endif // FWRETRACT
/**
* Volumetric extrusion M200
*/
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOPGM("Filament settings:");
if (volumetric_enabled)
SERIAL_EOL;
else
SERIAL_ECHOLNPGM(" Disabled");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 D", filament_size[0]);
SERIAL_EOL;
#if EXTRUDERS > 1
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]);
SERIAL_EOL;
#if EXTRUDERS > 2
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]);
SERIAL_EOL;
#if EXTRUDERS > 3
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T3 D", filament_size[3]);
SERIAL_EOL;
#if EXTRUDERS > 4
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T4 D", filament_size[4]);
SERIAL_EOL;
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
#endif // EXTRUDERS > 1
SERIAL_ECHOLNPAIR(" M209 S", autoretract_enabled ? 1 : 0);
if (!volumetric_enabled) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM(" M200 D0");
}
#endif // FWRETRACT
/**
* Auto Bed Leveling
*/
#if HAS_BED_PROBE
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Z-Probe Offset (mm):");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Z-Probe Offset (mm):");
}
SERIAL_ECHOPAIR(" M851 Z", zprobe_zoffset);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOLNPAIR(" M851 Z", LINEAR_UNIT(zprobe_zoffset));
#endif
/**
* TMC2130 stepper driver current
*/
#if ENABLED(HAVE_TMC2130)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Stepper driver current:");
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Stepper driver current:");
}
CONFIG_ECHO_START;
SERIAL_ECHO(" M906");
#if ENABLED(X_IS_TMC2130)
SERIAL_ECHOPAIR(" X", stepperX.getCurrent());

Write Preview
Loading…
Cancel
Save