Bo Herrmannsen
10 years ago
1 changed files with 0 additions and 210 deletions
@ -1,210 +0,0 @@ |
|||||
## Implemented G Codes |
|
||||
|
|
||||
- [Movement F and M Codes](#movement-g-and-m-codes) |
|
||||
- [SD Card M Codes](#sd-card-m-codes) |
|
||||
- [Hardware Control](#hardware-control) |
|
||||
- [Temperature M Codes](#temperature-m-codes) |
|
||||
- [Message M Codes](#message-m-codes) |
|
||||
- [Endstops M Codes](#endstops-m-codes) |
|
||||
- [Special Features M Codes](#special-features-m-codes) |
|
||||
- [Units and Measures G and M Codes](#units-and-measures-g-and-m-codes) |
|
||||
- [Firmware Retraction G and M Codes](#firmware-retraction-g-and-m-codes) |
|
||||
- [Z Probe G and M Codes](#z-probe-g-and-m-codes) |
|
||||
- [Filament Diameter M Codes](#filament-diameter-m-codes) |
|
||||
- [EEPROM Settings M Codes](#eeprom-settings-m-codes) |
|
||||
- [Delta M Codes](#delta-m-codes) |
|
||||
- [Stepper Driver M Codes](#stepper-driver-m-codes) |
|
||||
- [SCARA M Codes](#scara-m-codes) |
|
||||
- [GCode Comments](#comments) |
|
||||
|
|
||||
### Movement G and M Codes |
|
||||
``` |
|
||||
G0 -> G1 |
|
||||
G1 - Coordinated Movement X Y Z E |
|
||||
G2 - CW ARC |
|
||||
G3 - CCW ARC |
|
||||
G4 - Dwell S[seconds] or P[milliseconds] |
|
||||
G92 - Set the "current position" to coordinates: X<xpos> Y<ypos> Z<zpos> E<epos> |
|
||||
M0 - Wait for user, with optional prompt message (requires LCD controller) |
|
||||
M0 Click When Ready ; show "Click When Ready" until the button is pressed. |
|
||||
M1 - Same as M0 |
|
||||
M400 - Finish all moves |
|
||||
M999 - Restart after being stopped by error |
|
||||
``` |
|
||||
### SD Card M Codes |
|
||||
``` |
|
||||
M20 - List SD card |
|
||||
M21 - Init SD card |
|
||||
M22 - Release SD card |
|
||||
M23 - Select SD file (M23 filename.g) |
|
||||
M24 - Start/resume SD print |
|
||||
M25 - Pause SD print |
|
||||
M26 - Set SD position in bytes (M26 S12345) |
|
||||
M27 - Report SD print status |
|
||||
M28 - Start SD write (M28 filename.g) |
|
||||
M29 - Stop SD write |
|
||||
M30 - Delete file from SD (M30 filename.g) |
|
||||
M31 - Output time since last M109 or SD card start to serial |
|
||||
M32 - Select file and start SD print (Can be used _while_ printing from SD card files): |
|
||||
syntax "M32 /path/filename#", or "M32 S<startpos bytes> !filename#" |
|
||||
Call gcode file : "M32 P !filename#" and return to caller file after finishing (similar to #include). |
|
||||
The '#' is necessary when calling from within sd files, as it stops buffer prereading |
|
||||
M540 - Enable/Disable "Stop SD Print on Endstop Hit" (req. ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) |
|
||||
M540 S<0|1> |
|
||||
M928 - Start SD logging (M928 filename.g) - ended by M29 |
|
||||
``` |
|
||||
### Hardware Control |
|
||||
``` |
|
||||
M42 - Change pin status via gcode: P<pin> S<value>. If P is omitted the onboard LED pin will be used. |
|
||||
M42 P9 S1 ; set PIN 9 to 1. |
|
||||
M80 - Turn on Power Supply |
|
||||
M81 - Turn off Power Supply |
|
||||
M84 - Disable steppers until next move, |
|
||||
or use S<seconds> to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. |
|
||||
M85 - Set inactivity shutdown timer with parameter S<seconds>. Disable with "M85" or "M85 S0". |
|
||||
M112 - Emergency stop. Requires hardware reset!! |
|
||||
M226 - Wait for a pin to be in some state: P<pin number> S<pin state> |
|
||||
``` |
|
||||
### Temperature M Codes |
|
||||
``` |
|
||||
M104 - Set extruder target temp |
|
||||
M105 - Read current temp |
|
||||
M106 - Fan on |
|
||||
M107 - Fan off |
|
||||
M109 - Sxxx Wait for extruder current temp to reach target temp. Waits only when heating |
|
||||
Rxxx Wait for extruder current temp to reach target temp. Waits when heating and cooling |
|
||||
IF AUTOTEMP is enabled, S<mintemp> B<maxtemp> F<factor>. Exit autotemp by any M109 without F |
|
||||
M140 - Set bed target temp |
|
||||
M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating |
|
||||
Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling |
|
||||
M301 - Set PID parameters P I and D |
|
||||
M302 - Allow cold extrudes, or set the minimum extrude S<temperature>. |
|
||||
M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C) |
|
||||
M304 - Set bed PID parameters P I and D |
|
||||
``` |
|
||||
### Message M Codes |
|
||||
``` |
|
||||
M114 - Output current position to serial port |
|
||||
M115 - Capabilities string |
|
||||
M117 - Display message text on the LCD |
|
||||
M119 - Output Endstop status to serial port |
|
||||
``` |
|
||||
### Endstops M Codes |
|
||||
``` |
|
||||
M120 - Enable endstop detection |
|
||||
M121 - Disable endstop detection |
|
||||
``` |
|
||||
### Special Features M Codes |
|
||||
``` |
|
||||
M126 - Solenoid Air Valve Open (BariCUDA support by jmil) |
|
||||
M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil) |
|
||||
M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) |
|
||||
M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) |
|
||||
M150 - Set BlinkM Color: R<red> U<green> B<blue> via I2C. Range: 0-255 |
|
||||
M240 - Trigger a camera to take a photograph. (Add to your per-layer GCode.) |
|
||||
M250 - Set LCD contrast: C<0-63> |
|
||||
M280 - Set servo position absolute. P<servo index> S<angle or microseconds> |
|
||||
M300 - Play beep sound S<frequency Hz> P<duration ms> |
|
||||
M380 - Activate solenoid on active extruder |
|
||||
M381 - Disable all solenoids |
|
||||
M600 - Pause for filament change X<xpos> Y<ypos> Z<lift> E<initial retract> L<later retract for removal> |
|
||||
``` |
|
||||
### Units and Measures G and M Codes |
|
||||
``` |
|
||||
G90 - Use Absolute Coordinates |
|
||||
G91 - Use Relative Coordinates |
|
||||
M82 - Set E codes absolute (default) |
|
||||
M83 - Set E codes relative while in Absolute Coordinates (G90) mode |
|
||||
M92 - Set axis_steps_per_unit - same syntax as G92 |
|
||||
M200 - Set filament diameter and set E axis units to mm^3 (use S0 to set back to mm).: D<mm> |
|
||||
M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) |
|
||||
M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! |
|
||||
M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec |
|
||||
M204 - Set default acceleration: P for Printing moves, R for Retract only (no X, Y, Z) moves and T for Travel (non printing) moves (ex. M204 P800 T3000 R9000) in mm/sec^2 |
|
||||
M205 - Advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X=maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk |
|
||||
M206 - Set additional homing offset |
|
||||
M218 - Set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y> |
|
||||
M220 - Set speed factor override percentage: S<factor in percent> |
|
||||
M221 - Set extrude factor override percentage: S<factor in percent> |
|
||||
``` |
|
||||
### Firmware Retraction G and M Codes |
|
||||
``` |
|
||||
G10 - Retract filament according to settings of M207 |
|
||||
G11 - Retract recover filament according to settings of M208 |
|
||||
M207 - Set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting |
|
||||
M208 - Set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/s] |
|
||||
M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction |
|
||||
``` |
|
||||
### Z Probe G and M Codes |
|
||||
``` |
|
||||
G28 - Home all Axis |
|
||||
G29 - Detailed Z-Probe, probes the bed at 3 or more points. The printer must be homed with G28 before G29. |
|
||||
G30 - Single Z Probe, probes bed at current XY location. |
|
||||
G31 - Dock Z Probe sled (if enabled) |
|
||||
G32 - Undock Z Probe sled (if enabled) |
|
||||
M48 - Measure Z_Probe repeatability: P<points> X<xpos> Y<ypos> V<verbosity> E=engage L<legs of travel> |
|
||||
As with G29, the E flag causes the probe to stow after each probe. |
|
||||
M401 - Lower Z-probe (if present) |
|
||||
M402 - Raise Z-probe (if present) |
|
||||
``` |
|
||||
### Filament Diameter M Codes |
|
||||
``` |
|
||||
M404 - Set (or display) Nominal Filament Diameter in mm: [N<diameter>] (e.g., 3mm or 1.75mm) |
|
||||
M405 - Turn on Filament Sensor extrusion control: [D<distance>] to set distance (in cm) from sensor to extruder |
|
||||
M406 - Turn off Filament Sensor extrusion control |
|
||||
M407 - Display measured Filament Diameter |
|
||||
``` |
|
||||
### EEPROM Settings M Codes |
|
||||
``` |
|
||||
M500 - Store parameters in EEPROM |
|
||||
M501 - Read parameters from EEPROM (if you need reset them after you changed them temporarily). |
|
||||
M502 - Revert to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. |
|
||||
M503 - Print the current settings (from memory not from EEPROM). Use S0 to leave off headings. |
|
||||
``` |
|
||||
### Delta M Codes |
|
||||
``` |
|
||||
M665 - Set Delta configurations: L<diagonal rod> R<delta radius> S<segments/s> |
|
||||
M666 - Set Delta endstop adjustment: X<x-adjustment> Y<y-adjustment> Z<z-adjustment> |
|
||||
M605 - Set dual x-carriage movement mode: S<mode> [ X<duplication x-offset> R<duplication temp offset> ] |
|
||||
``` |
|
||||
### Stepper Driver M Codes |
|
||||
``` |
|
||||
M17 - Enable/Power all stepper motors |
|
||||
M18 - Disable all stepper motors. (same as M84) |
|
||||
M907 - Set digital trimpot motor current using axis codes. |
|
||||
M908 - Control digital trimpot directly. |
|
||||
M350 - Set microstepping mode. |
|
||||
M351 - Toggle MS1 MS2 pins directly. |
|
||||
``` |
|
||||
### SCARA M-Codes |
|
||||
__May change to suit future G-code standards__ |
|
||||
``` |
|
||||
M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration) |
|
||||
M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree) |
|
||||
M362 - SCARA calibration: Move to cal-position PsiA (0 deg calibration) |
|
||||
M363 - SCARA calibration: Move to cal-position PsiB (90 deg calibration - steps per degree) |
|
||||
M364 - SCARA calibration: Move to cal-position PSIC (90 deg to Theta calibration position) |
|
||||
M365 - SCARA calibration: Scaling factor, X, Y, Z axis |
|
||||
``` |
|
||||
|
|
||||
## Comments |
|
||||
|
|
||||
Comments start at a `;` (semicolon) and end with the end of the line: |
|
||||
|
|
||||
N3 T0*57 ; This is a comment |
|
||||
N4 G92 E0*67 |
|
||||
; So is this |
|
||||
N5 G28*22 |
|
||||
|
|
||||
(example taken from the [RepRap wiki](http://reprap.org/wiki/Gcode#Comments)) |
|
||||
|
|
||||
If you need to use a literal `;` somewhere (for example within `M117`), you can escape semicolons with a `\` |
|
||||
(backslash): |
|
||||
|
|
||||
M117 Hello \;) |
|
||||
|
|
||||
`\` can also be used to escape `\` itself, if you need a literal `\` in front of a `;`: |
|
||||
|
|
||||
M117 backslash: \\;and a comment |
|
||||
|
|
||||
Please note that hosts should strip any comments before sending GCODE to the printer in order to save bandwidth. |
|
||||
Loading…
Reference in new issue