andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Z Axis Safe Homing when using Z Probe 

Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)

This feature has two changes:

1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:

Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT

2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
pull/1/head
Alex Borro 11 years ago
parent
35905ea4f9
commit
b33375d438
4 changed files with 128 additions and 35 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 38
      Marlin/Configuration.h
  2. 13
      Marlin/Marlin.h
  3. 86
      Marlin/Marlin_main.cpp
  4. 18
      Marlin/language.h

38
Marlin/Configuration.h
View File

@ -305,6 +305,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// Travel limits after homing
#define X_MAX_POS 205
#define X_MIN_POS 0
#define Y_MAX_POS 205
#define Y_MIN_POS 0
#define Z_MAX_POS 200
#define Z_MIN_POS 0
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
//============================= Bed Auto Leveling ===========================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
@ -337,19 +348,26 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
//If you have enabled the Bed Auto Levelling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
// When defined, it will:
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled
// - If stepper drivers timeout, it will need X and Y homing again before Z homing
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
// - Block Z homing only when the probe is outside bed area.
#ifdef Z_SAFE_HOMING
#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28)
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28)
#endif
// Travel limits after homing
#define X_MAX_POS 205
#define X_MIN_POS 0
#define Y_MAX_POS 205
#define Y_MIN_POS 0
#define Z_MAX_POS 200
#define Z_MIN_POS 0
#endif
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used

13
Marlin/Marlin.h
View File

@ -107,10 +107,10 @@ void manage_inactivity();
#if defined(DUAL_X_CARRIAGE) && defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1 \
&& defined(X2_ENABLE_PIN) && X2_ENABLE_PIN > -1
#define enable_x() do { WRITE(X_ENABLE_PIN, X_ENABLE_ON); WRITE(X2_ENABLE_PIN, X_ENABLE_ON); } while (0)
#define disable_x() do { WRITE(X_ENABLE_PIN,!X_ENABLE_ON); WRITE(X2_ENABLE_PIN,!X_ENABLE_ON); } while (0)
#define disable_x() do { WRITE(X_ENABLE_PIN,!X_ENABLE_ON); WRITE(X2_ENABLE_PIN,!X_ENABLE_ON); axis_known_position[X_AXIS] = false; } while (0)
#elif defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#define disable_x() { WRITE(X_ENABLE_PIN,!X_ENABLE_ON); axis_known_position[X_AXIS] = false; }
#else
#define enable_x() ;
#define disable_x() ;
@ -119,10 +119,10 @@ void manage_inactivity();
#if defined(Y_ENABLE_PIN) && Y_ENABLE_PIN > -1
#ifdef Y_DUAL_STEPPER_DRIVERS
#define enable_y() { WRITE(Y_ENABLE_PIN, Y_ENABLE_ON); WRITE(Y2_ENABLE_PIN, Y_ENABLE_ON); }
#define disable_y() { WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON); WRITE(Y2_ENABLE_PIN, !Y_ENABLE_ON); }
#define disable_y() { WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON); WRITE(Y2_ENABLE_PIN, !Y_ENABLE_ON); axis_known_position[Y_AXIS] = false; }
#else
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#define disable_y() { WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON); axis_known_position[Y_AXIS] = false; }
#endif
#else
#define enable_y() ;
@ -132,10 +132,10 @@ void manage_inactivity();
#if defined(Z_ENABLE_PIN) && Z_ENABLE_PIN > -1
#ifdef Z_DUAL_STEPPER_DRIVERS
#define enable_z() { WRITE(Z_ENABLE_PIN, Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN, Z_ENABLE_ON); }
#define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); }
#define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
#else
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
#endif
#else
#define enable_z() ;
@ -209,6 +209,7 @@ extern float endstop_adj[3];
#endif
extern float min_pos[3];
extern float max_pos[3];
extern bool axis_known_position[3];
extern int fanSpeed;
#ifdef BARICUDA
extern int ValvePressure;

86
Marlin/Marlin_main.cpp
View File

@ -43,6 +43,7 @@
#include "ConfigurationStore.h"
#include "language.h"
#include "pins_arduino.h"
#include "math.h"
#ifdef BLINKM
#include "BlinkM.h"
@ -191,6 +192,7 @@ float endstop_adj[3]={0,0,0};
#endif
float min_pos[3] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS };
float max_pos[3] = { X_MAX_POS, Y_MAX_POS, Z_MAX_POS };
bool axis_known_position[3] = {false, false, false};
// Extruder offset
#if EXTRUDERS > 1
@ -949,16 +951,11 @@ static void homeaxis(int axis) {
current_position[axis] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
// Engage Servo endstop if enabled
#ifdef SERVO_ENDSTOPS
#if defined (ENABLE_AUTO_BED_LEVELING) && (PROBE_SERVO_DEACTIVATION_DELAY > 0)
if (axis==Z_AXIS) {
#if defined (Z_RAISE_BEFORE_HOMING) && (Z_RAISE_BEFORE_HOMING > 0)
destination[axis] = Z_RAISE_BEFORE_HOMING * axis_home_dir * (-1); // Set destination away from bed
feedrate = max_feedrate[axis];
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate, active_extruder);
st_synchronize();
#endif
engage_z_probe();
}
else
@ -1000,6 +997,7 @@ static void homeaxis(int axis) {
destination[axis] = current_position[axis];
feedrate = 0.0;
endstops_hit_on_purpose();
axis_known_position[axis] = true;
// Retract Servo endstop if enabled
#ifdef SERVO_ENDSTOPS
@ -1208,12 +1206,6 @@ void process_commands()
HOMEAXIS(Y);
}
#if Z_HOME_DIR < 0 // If homing towards BED do Z last
if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) {
HOMEAXIS(Z);
}
#endif
if(code_seen(axis_codes[X_AXIS]))
{
if(code_value_long() != 0) {
@ -1227,13 +1219,73 @@ void process_commands()
}
}
#if Z_HOME_DIR < 0 // If homing towards BED do Z last
#ifndef Z_SAFE_HOMING
if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) {
#if defined (Z_RAISE_BEFORE_HOMING) && (Z_RAISE_BEFORE_HOMING > 0)
destination[Z_AXIS] = Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS) * (-1); // Set destination away from bed
feedrate = max_feedrate[Z_AXIS];
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate, active_extruder);
st_synchronize();
#endif
HOMEAXIS(Z);
}
#else // Z Safe mode activated.
if(home_all_axis) {
destination[X_AXIS] = round(Z_SAFE_HOMING_X_POINT - X_PROBE_OFFSET_FROM_EXTRUDER);
destination[Y_AXIS] = round(Z_SAFE_HOMING_Y_POINT - Y_PROBE_OFFSET_FROM_EXTRUDER);
destination[Z_AXIS] = Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS) * (-1); // Set destination away from bed
feedrate = XY_TRAVEL_SPEED;
current_position[Z_AXIS] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate, active_extruder);
st_synchronize();
current_position[X_AXIS] = destination[X_AXIS];
current_position[Y_AXIS] = destination[Y_AXIS];
HOMEAXIS(Z);
}
// Let's see if X and Y are homed and probe is inside bed area.
if(code_seen(axis_codes[Z_AXIS])) {
if ( (axis_known_position[X_AXIS]) && (axis_known_position[Y_AXIS]) \
&& (current_position[X_AXIS]+X_PROBE_OFFSET_FROM_EXTRUDER >= X_MIN_POS) \
&& (current_position[X_AXIS]+X_PROBE_OFFSET_FROM_EXTRUDER <= X_MAX_POS) \
&& (current_position[Y_AXIS]+Y_PROBE_OFFSET_FROM_EXTRUDER >= Y_MIN_POS) \
&& (current_position[Y_AXIS]+Y_PROBE_OFFSET_FROM_EXTRUDER <= Y_MAX_POS)) {
current_position[Z_AXIS] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
destination[Z_AXIS] = Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS) * (-1); // Set destination away from bed
feedrate = max_feedrate[Z_AXIS];
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate, active_extruder);
st_synchronize();
HOMEAXIS(Z);
} else if (!((axis_known_position[X_AXIS]) && (axis_known_position[Y_AXIS]))) {
LCD_MESSAGEPGM(MSG_POSITION_UNKNOWN);
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(MSG_POSITION_UNKNOWN);
} else {
LCD_MESSAGEPGM(MSG_ZPROBE_OUT);
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(MSG_ZPROBE_OUT);
}
}
#endif
#endif
if(code_seen(axis_codes[Z_AXIS])) {
if(code_value_long() != 0) {
current_position[Z_AXIS]=code_value()+add_homeing[2];
}
}
#ifdef ENABLE_AUTO_BED_LEVELING
if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) {
current_position[Z_AXIS] -= Z_PROBE_OFFSET_FROM_EXTRUDER; //Add Z_Probe offset (the distance is negative)
}
#endif
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
#endif // else DELTA
@ -1275,9 +1327,9 @@ void process_commands()
do_blocking_move_to(LEFT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, BACK_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
engage_z_probe(); // Engage Z Servo endstop if available
run_z_probe();
float z_at_xLeft_yBack = current_position[Z_AXIS];
retract_z_probe();
SERIAL_PROTOCOLPGM("Bed x: ");
SERIAL_PROTOCOL(LEFT_PROBE_BED_POSITION);
@ -1290,8 +1342,11 @@ void process_commands()
// prob 2
do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
do_blocking_move_to(LEFT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, FRONT_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
engage_z_probe(); // Engage Z Servo endstop if available
run_z_probe();
float z_at_xLeft_yFront = current_position[Z_AXIS];
retract_z_probe();
SERIAL_PROTOCOLPGM("Bed x: ");
SERIAL_PROTOCOL(LEFT_PROBE_BED_POSITION);
@ -1305,8 +1360,11 @@ void process_commands()
do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
// the current position will be updated by the blocking move so the head will not lower on this next call.
do_blocking_move_to(RIGHT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, FRONT_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
engage_z_probe(); // Engage Z Servo endstop if available
run_z_probe();
float z_at_xRight_yFront = current_position[Z_AXIS];
retract_z_probe(); // Retract Z Servo endstop if available
SERIAL_PROTOCOLPGM("Bed x: ");
SERIAL_PROTOCOL(RIGHT_PROBE_BED_POSITION);
@ -1320,8 +1378,6 @@ void process_commands()
set_bed_level_equation(z_at_xLeft_yFront, z_at_xRight_yFront, z_at_xLeft_yBack);
retract_z_probe(); // Retract Z Servo endstop if available
st_synchronize();
// The following code correct the Z height difference from z-probe position and hotend tip position.

18
Marlin/language.h
View File

@ -136,6 +136,8 @@
#define MSG_FILAMENTCHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -301,6 +303,8 @@
#define MSG_FILAMENTCHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -465,6 +469,8 @@
#define MSG_FILAMENTCHANGE "Changer filament"
#define MSG_INIT_SDCARD "Init. la carte SD"
#define MSG_CNG_SDCARD "Changer de carte SD"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -632,6 +638,8 @@
#define MSG_FILAMENTCHANGE "Filament wechseln"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -803,6 +811,8 @@
#define MSG_RETRACT_ARROW "Retraer"
#define MSG_PART_RELEASE "Desacople Parcial"
#define MSG_STEPPER_RELEASED "Desacoplada."
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -964,6 +974,8 @@
#define MSG_FILAMENTCHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -1125,6 +1137,8 @@
#define MSG_FILAMENTCHANGE "Cambia filamento"
#define MSG_INIT_SDCARD "Iniz. SD-Card"
#define MSG_CNG_SDCARD "Cambia SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages
@ -1295,6 +1309,8 @@
#define MSG_FILAMENTCHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "Sonda fora da mesa"
#define MSG_POSITION_UNKNOWN "Home X/Y antes de Z"
// Serial Console Messages
@ -1461,6 +1477,8 @@
#define MSG_FILAMENTCHANGE "Change filament"
#define MSG_INIT_SDCARD "Init. SD-Card"
#define MSG_CNG_SDCARD "Change SD-Card"
#define MSG_ZPROBE_OUT "ZProbe Outside Bed"
#define MSG_POSITION_UNKNOWN "Home X/Y before Z"
// Serial Console Messages

Write Preview
Loading…
Cancel
Save