|
|
|
@ -31,7 +31,7 @@ |
|
|
|
// Sanguinololu 1.2 and above = 62
|
|
|
|
// Ultimaker = 7,
|
|
|
|
// Teensylu = 8
|
|
|
|
#define MOTHERBOARD 5 |
|
|
|
#define MOTHERBOARD 7 |
|
|
|
|
|
|
|
//===========================================================================
|
|
|
|
//=============================Thermal Settings ============================
|
|
|
|
@ -176,10 +176,10 @@ const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the |
|
|
|
//#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
|
|
|
|
//#define INVERT_E_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
|
|
|
|
|
|
//#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
|
|
|
//#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
|
|
|
//#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
|
|
|
//#define INVERT_E_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
|
|
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
|
|
|
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
|
|
|
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
|
|
|
#define INVERT_E_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
|
|
|
|
|
|
|
//// ENDSTOP SETTINGS:
|
|
|
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
|
|
|
@ -242,11 +242,11 @@ const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the |
|
|
|
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
|
|
|
|
// this enables the watchdog interrupt.
|
|
|
|
//#define USE_WATCHDOG
|
|
|
|
#ifdef USE_WATCHDOG |
|
|
|
//#ifdef USE_WATCHDOG
|
|
|
|
// you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
|
|
|
|
//#define RESET_MANUAL
|
|
|
|
//#define WATCHDOG_TIMEOUT 4 //seconds
|
|
|
|
|
|
|
|
//#endif
|
|
|
|
|
|
|
|
// extruder advance constant (s2/mm3)
|
|
|
|
//
|
|
|
|
@ -272,7 +272,7 @@ const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the |
|
|
|
//#define ULTRA_LCD //general lcd support, also 16x2
|
|
|
|
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
|
|
|
|
|
|
|
//#define ULTIPANEL
|
|
|
|
#define ULTIPANEL |
|
|
|
#ifdef ULTIPANEL |
|
|
|
// #define NEWPANEL //enable this if you have a click-encoder panel
|
|
|
|
#define SDSUPPORT |
|
|
|
|
Erik van der Zalm
13 years ago