Update copyright in header, etc. (#14645)

Marlin/src/pins/lpc1768/pins_MKS_SBASE.h

@@ -304,9 +304,14 @@
 #endif
 
 #if MB(MKS_SBASE) && HAS_TMC220x
-  // The shortage of pins becomes apparent.
-  // Worst case you may have to give up the LCD
-  // RX pins need to be interrupt capable
+
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * The shortage of pins becomes apparent.
+   * Worst case you may have to give up the LCD
+   * RX pins need to be interrupt capable
+   */
   #define X_SERIAL_TX_PIN  P1_22   // J8-2
   #define X_SERIAL_RX_PIN  P2_12   // J8-4 Interrupt Capable
   #define Y_SERIAL_TX_PIN  P1_23   // J8-3
@@ -344,7 +349,7 @@
  *  PWM1.6   P2_05   RAMPS_D10_PIN
  */
 
- /**
+/**
  * Special pins
  *   P1_30 - not 5V tolerant - EXP1
  *   P1_31 - not 5V tolerant - EXP1
@@ -353,7 +358,7 @@
  *
  */
 
- /**
+/**
  * Serial Ports
  *   P0_00 - Port  3
  *   P0_01 - SD Card (Onboard)

Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h

@@ -110,7 +110,7 @@
 
 #if HAS_TMC220x
   /**
-   * TMC2208 stepper drivers
+   * TMC2208/TMC2209 stepper drivers
    *
    * Hardware serial communication ports.
    * If undefined software serial is used according to the pins below

Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h

@@ -121,9 +121,9 @@
    * If undefined software serial is used according to the pins below
    */
 
-  /**
-   * Software serial
-   */
+  //
+  // Software serial
+  //
 
   // P2_08 E1-Step
   // P2_13 E1-Dir

Marlin/src/pins/lpc1769/pins_MKS_SGEN.h

@@ -44,9 +44,13 @@
 //#define BTN_EN2            P1_22   // EXP2.3
 
 #if HAS_TMC220x
-  // The shortage of pins becomes apparent.
-  // In the worst case you may have to give up the LCD.
-  // RX pins must be interrupt-capable.
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * The shortage of pins becomes apparent.
+   * In the worst case you may have to give up the LCD.
+   * RX pins must be interrupt-capable.
+   */
   #define X_SERIAL_TX_PIN  P4_29   // J8-2
   #define X_SERIAL_RX_PIN  P4_29   // J8-2
 

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -118,8 +118,12 @@
 //
 
 #if HAS_TMC220x
-  // Software serial
-  // At the moment, F6 rx pins are not pc interrupt pins
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * Software serial communication pins.
+   * At the moment, F6 rx pins are not pc interrupt pins
+   */
   #define X_SERIAL_RX_PIN  -1   // 71
   #define X_SERIAL_TX_PIN  72
   #define Y_SERIAL_RX_PIN  -1   // 73

Marlin/src/pins/ramps/pins_TT_OSCAR.h

@@ -1,9 +1,9 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  *
  * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -99,9 +99,9 @@
 #define E4_ENABLE_PIN      47
 #define E4_CS_PIN          E0_CS_PIN
 
-#if ENABLED(HAVE_TMC2208)
+#if HAS_TMC220x
   /**
-   * TMC2208 stepper drivers
+   * TMC2208/TMC2209 stepper drivers
    *
    * Hardware serial communication ports.
    * If undefined software serial is used according to the pins below