Browse Source

Smaller I2CPositionEncoder strings

pull/1/head
Scott Lahteine 6 years ago
parent
commit
a0dadc8c62
  1. 22
      Marlin/src/feature/I2CPositionEncoder.cpp

22
Marlin/src/feature/I2CPositionEncoder.cpp

@ -155,7 +155,7 @@ void I2CPositionEncoder::update() {
#ifdef I2CPE_ERR_THRESH_ABORT
if (ABS(error) > I2CPE_ERR_THRESH_ABORT * planner.settings.axis_steps_per_mm[encoderAxis]) {
//kill(PSTR("Significant Error"));
SERIAL_ECHOLNPAIR("Axis error greater than set threshold, aborting!", error);
SERIAL_ECHOLNPAIR("Axis error over threshold, aborting!", error);
safe_delay(5000);
}
#endif
@ -379,12 +379,12 @@ bool I2CPositionEncoder::test_axis() {
void I2CPositionEncoder::calibrate_steps_mm(const uint8_t iter) {
if (type != I2CPE_ENC_TYPE_LINEAR) {
SERIAL_ECHOLNPGM("Steps per mm calibration is only available using linear encoders.");
SERIAL_ECHOLNPGM("Steps/mm calibration requires linear encoder.");
return;
}
if (!(encoderAxis == X_AXIS || encoderAxis == Y_AXIS || encoderAxis == Z_AXIS)) {
SERIAL_ECHOLNPGM("Automatic steps / mm calibration not supported for this axis.");
SERIAL_ECHOLNPGM("Steps/mm calibration not supported for this axis.");
return;
}
@ -436,18 +436,18 @@ void I2CPositionEncoder::calibrate_steps_mm(const uint8_t iter) {
travelledDistance = mm_from_count(ABS(stopCount - startCount));
SERIAL_ECHOPAIR("Attempted to travel: ", travelDistance);
SERIAL_ECHOLNPGM("mm.");
SERIAL_ECHOPAIR("Attempted travel: ", travelDistance);
SERIAL_ECHOLNPGM("mm");
SERIAL_ECHOPAIR("Actually travelled: ", travelledDistance);
SERIAL_ECHOLNPGM("mm.");
SERIAL_ECHOPAIR(" Actual travel: ", travelledDistance);
SERIAL_ECHOLNPGM("mm");
//Calculate new axis steps per unit
old_steps_mm = planner.settings.axis_steps_per_mm[encoderAxis];
new_steps_mm = (old_steps_mm * travelDistance) / travelledDistance;
SERIAL_ECHOLNPAIR("Old steps per mm: ", old_steps_mm);
SERIAL_ECHOLNPAIR("New steps per mm: ", new_steps_mm);
SERIAL_ECHOLNPAIR("Old steps/mm: ", old_steps_mm);
SERIAL_ECHOLNPAIR("New steps/mm: ", new_steps_mm);
//Save new value
planner.settings.axis_steps_per_mm[encoderAxis] = new_steps_mm;
@ -464,12 +464,12 @@ void I2CPositionEncoder::calibrate_steps_mm(const uint8_t iter) {
if (iter > 1) {
total /= (float)iter;
SERIAL_ECHOLNPAIR("Average steps per mm: ", total);
SERIAL_ECHOLNPAIR("Average steps/mm: ", total);
}
ec = oldec;
SERIAL_ECHOLNPGM("Calculated steps per mm has been set. Please save to EEPROM (M500) if you wish to keep these values.");
SERIAL_ECHOLNPGM("Calculated steps/mm set. Use M500 to save to EEPROM.");
}
void I2CPositionEncoder::reset() {

Loading…
Cancel
Save